SL & Jiva EL EL Jiva SL (TP-5700 / TP-5800) SERIES TECHNICAL MANUAL WORK STATION Rev.
SOME IMPORTANT NOTES FCC NOTES This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment.
TABLE OF CONTENTS OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 OPTIONAL ITEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3 GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 SYSTEM . . . .
DELUXE UPGRADE KIT KP100 . . . . . . . . . . . . . . . . . . . MAGNETIC STRIPE READER . . . . . . . . . . . . . . . . . . . . SMART CARD READER . . . . . . . . . . . . . . . . . . . . . . . . . FINGER PRINT SENSOR . . . . . . . . . . . . . . . . . . . . . . . . iBUTTON READER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UPS BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INTERNAL CD ROM DRIVE . . . . . . . . . . . . . . . . . . . . . . ELOTOUCH TOUCH PANEL . . . . . .
PARALLEL PORT LPT1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LAN PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS/2 KEYBOARD CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . PS/2 MOUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUDIO OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MIC IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER SWITCH MANAGER . . . . . . . . . . . . . . . . . . . . POWER CONTROL FUNCTIONS . . . . . . . . . . . . . . . . . POWER SWITCH SETTING . . . . . . . . . . . . . . . . . . . . . UPS BATTERY STATUS . . . . . . . . . . . . . . . . . . . . . . . POWER OFF DELAY TIME . . . . . . . . . . . . . . . . . . . . . SAVE AND EXIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . CANCEL AND EXIT . . . . . . . . . . . . . . . . . . . . . . . . . . PROGRAMMABLE KEYBOARD . . . . . . . . . . . . . . . . . .
SOLDER SIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . JUMPERS AND CONNECTORS . . . . . . . . . . . . . . . . . . On component side . . . . . . . . . . . . . . . . . . . . . . . . . . . . On solder side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . JUMPER SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . CMOS data control . . . . . . . . . . . . . . . . . . . . . . . . . . . COM1/COM2 DC supply select . . . . . . . . . . . . . . . . . . .
OVERVIEW SCOPE The Jiva SL (TP5700) & Jiva EL (TP5800) series is a series of fully integrated PC based Point-Of-Sale terminals. This series provides the best performance and the most user-friendly interface for Point-Of-Sale, Hospitality and Kiosk systems. This series also provides an industrial-use touch control panel over the 12” or 15” LCD integrated on the front surface of the system.
e. f. g. h. i. l l l l l l l l l l l l 2 USB 2.0 ports 1 LAN port 10/100 base T Ethernet 1 Compact Flash memory card connector (for Jiva SL systems only) 1 external VGA monitor port 1 cash drawer connector for control over 2 cash drawers with drawer open detection j. 1 UPS battery connector (for optional UPS battery in base) k. 1 external CD ROM drive connector (for Jiva EL systems only) l. 1 DC 12 V input connector m.
l l l Integrated structure for optional security devices (incl. top mount LCD customer display and side mount security device with 40 keys programmable keypad, smart card reader, finger print sensor, MSR) Software programmable MSR parameters in KP100 for Win 98 or Win XP VGA memory size programmable by software up to (8 – 64 MB) OPTIONAL ITEMS Note: The “∗” marked items in the following list means that option must be set prior to shipment from the factory. The rest items can be set by the dealers.
l Fanless design on Jiva SL (TP5700) series reduces dust/grease accumulation, makes the machine the most reliable one and provides an easy replacement of the memory storage device without opening the system.
GENERAL SPECIFICATION SYSTEM l l l l CPU speed : Celeron compatible Eden series 400MHz up for TP5700; C3 800MHz up for TP5800 DRAM : DDR266 128 MB (expandable to 1GB) CF card 16 – 512 MB for TP5700 only Built-in 3.5” HDD 20 GB above in IDE interface for TP5800 only POWER SOURCE Item Specification Voltage range of adaptor input 100 ~ 240 V AC Load limit of adaptor input 1.8 A max. Input frequency 50 / 60 Hz Total Power Consumption Display used TP5700 TP5800 12.
UPS SUPPORT (battery option) l l l l Supports system operation for 3~8 min. depending on loading condition Green LED turned on when adaptor power stand-by Blue LED flashes and system beeps when UPS battery starts working and discharging, and Green LED flashes when UPS near to end Working on UPS battery status can be detected through COM1 status port 12VDC POWER SUPPLY INTO Jiva SL (TP5700) & Jiva EL (TP5800) l l O / P : 12 +/- 1 V DC 6.67 Amp min. for TP5800; 5 Amp min. for TP5700 I / P : 110 VAC/1.
TOUCH PANEL l l l l l Touch control interface: PS/2 mouse emulation Sensor type: resistive Resolution: 1024 x 1024 Calibration: initial calibration at setup only, no re-calibration required for day to day power on/off Driver support: DOS, Win98, Win CE, Win 2000, Win XP & Linux.
OPERATOR DISPLAY Display Type COLOR TFT 12” LCD COLOR TFT 15” LCD View area 246 X 184.5 mm 304.1 X 228.1 mm Internal Interface TTL TTL 2 250 cd/m2 min Luminance 150 cd/m Contrast Ratio 200:1 250:1 Resolution 1024 X 768 1024 X 768 Memory size 8 MB up to 64 MB share memory Tilt angle 18° ~ 87° AUDIO PORT l l l l l Output 2.83 Vp-p with max. output impedance 500 Ohm 20 dB gain for Microphone input Input impedance 20 KOhm Speaker load impedance 8 Ohm Output audio power 1.
l WEIGHT: NET WEIGHT GROSS WEIGHT TP5712 6.8 kgs (15.0lbs) 10.0 kgs (22.0 lbs) TP5715 7.0 kgs (15.4 lbs) 10.5 kg (23.1 lbs) TP5812 7.6 kgs (16.8lbs) 10.7 kgs (23.6lbs) TP5815 7.8 kgs (17.2 lbs) 11.2 kg (24.6 lbs) MECHANICAL NOISE LEVEL l l Max. 65 dB measured at 30 cm distance for TP5800 series Less than 30 dB for TP5700 series ENVIRONMENTAL l TEMPERATURE RANGE: (excl.
SAFETY APPROVALS l l Whole system meet CE, FCC class A standard (meet IEC1000-4-2/-3/-4/-5/-6/-8/-11) Power supply is UL, VDE & T-mark approved OPTIONS CUSTOMER DISPLAY MODEL Number PD302 PD2500 PD7200 Display Media LCD VFD LCD Number of rows 2 2 2/4/2 Characters per row 20 20 20 / 26 / 10 Character width (mm) 6 7.2 17.2 / 8.0 / 17.2 Character height (mm) 9.66 11.25 7.79 / 5.55 / 16.
GENERAL UPGRADE KIT SD100 l Functions include: MSR / smart card reader, finger print sensor / iButton reader DELUXE UPGRADE KIT KP100 l Functions include: MSR, keypad, smart card reader, finger print sensor MAGNETIC STRIPE READER l l l l l USB interface in SD100; PS/2 KB interface in KP100 ISO 2 tracks ((track 1 + track 2) or (track 2 + track 3)) ISO 3 tracks (track 1 + track 2 + track 3) Characteristic parameters of ISO readers can be set via software in KP100 or via hardware jumper setting in SD100 A
EXTERNAL CD ROM DRIVE l l l 24 x speed USB or ATA IDE interface Set as slave IDE device CASH DRAWER CONTROL CABLE l 2 in 1 cash drawer control cable 20863023800 for independent control over two cash drawers of CR3100 or CR3200 or CR4000 WIRELESS LAN l IEEE 802.11b with USB interface WALL MOUNT l Can be achieved by use of wall mount bracket EXTERNAL FLOPPY DISK DRIVE l l 3.5” 2HD/2DD Only USB interface model of this item is available in the market PRINTER: l PP-1000 1. Dot matrix 7 pin 2.
5. l Auto-detect between RS232 and EPP interface PP-3000 1. Dot matrix 9 pin 2. Bi-directional printing 3. Friction type 4. 40 columns for 15.4 CPI 5. Accepts paper width 2.25/3/3.25 inches with adjustable paper guide 6. Prints on ordinary or up to 3-fold carbonless copy paper l PP-5600 1. 2. 3. 4. 5. 6. l Dot matrix 9 pin Bi-directional printing with logic seeking Friction type 40 columns for 16.9 CPI Accepts paper width 3 inches Prints on ordinary or up to 3-fold carbonless copy paper PP-6000 1. 2.
3. 4. 5. 6. 7. 8. High resolution 8 dots/mm by 512 dots/line Epson TM-T88 II compatible command set Low noise high reliability Auto guillotine type cutter provides single point left partial cut Thermal sensitive paper roll at width 80 mm Supports UPC-A, EAN(JAN)13/8, ITF, CODE39, CODABAR printing 9. Supports printing on label with marker on the other side 10.
RELIABILITY SPECIFICATION l POWER ADAPTOR MTBF: 150,000 HRS l TOUCH PANEL LIFE EXPECTANCY: 10,000,000 UP TOUCHES AT SAME SPOT l LCD BACK LIGHT LIFE EXPECTANCY: 10,000 HRS FOR 12"; 40,000 HRS FOR 15" l HDD MTBF: 50,000 HRS l CUSTOMER DISPLAY LIFE EXPECTANCY: PD2500: 30,000 HRS PD302: 100,000 HRS (for BACK LIGHT) l BCCR / MSR LIFE EXPECTANCY: 300,000 PASSES l POWER SWITCH LIFE EXPECTANCY: 50,000 STROKES l MOTHER BOARD MTBF: 50,000 HOURS l EXTERNAL FDD MTBF: 80,000 HRS TP-5700/5800 series Tec
l EXTERNAL CD ROM DRIVE MTBF: 120,000 HRS l TP-5700/5800 series Technical Manual 3 - 2
SYSTEM DEFINITIONS BLOCK DIAGRAM UPS Battery UPS Circuit PWR MNGR 12 V DC Adaptor VGA Monitor PSU Circuit DDR 266 DRAM Module LCD Panel CPU Eden 400 or C3 800 in EBGA PS/2 Mouse Port Touch Panel Touch Controller LCD CCFL CCFL Inverter Riser Card CRT Port CLE266 (NB) VT8235 (SB) CR COM1 LPC I/O Chip W836970F NVSRAM COM2 Audio CODEC COM3 COM4 LPT Audio Line out PS/2 KB Port KB USB 0~1 USB Device LAN Chip BIOS CR3X00 CR4X00 PS/2 Mouse HDD Mic.
12 V DC IN CONNECTOR PIN ASSIGNMENT OF 4 PIN PLUG: PIN # 1 2 3 4 CASE DEFINITION +12 V +12 V GND GND CHASSIS GND 1 2 CASE 3 4 VGA CONNECTOR l This port is a standard 3 x 5 D-sub VGA connector PIN # 1 2 3 4 5 DEFINITION RED GREEN BLUE NCID2 GND PIN # 6 7 8 9 10 DEFINITION PIN # DEFINITION GND 11 NCID0 GND 12 NCID1 GND 13 HSYNC NC/+12VKEY 14 VSYNC GND 15 NCID3 CASH DRAWER CONTROLLER l This is a RJ11 jack for cash drawer control providing control ability over two cash drawers.
USB0 / USB1 PIN ASSIGNMENT OF EACH 4 PIN JACK: PIN # 1 2 3 4 DEFINITION VCC -DATA +DATA GND PIN 1 SERIAL PORT COM1 PIN ASSIGNMENT OF 9 PIN D SUB MALE CONNECTOR: DEFAULT SETTING PIN # DEFINITION ALTERNATIVE 1 DCD BATTWK DCD 2 RX 3 TX 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI CR OPEN / +5 VDC RI • IRQ 4 is assigned to this port. Can be changed in CMOS setup under “Super IO Controller” • Please refer to section “UPS DETECTION FUNCTION” in “APPLICATION GUIDE” for BATTWK signal.
SERIAL PORT COM2/3/4 PIN ASSIGNMENT OF 9 PIN D SUB MALE CONNECTOR: PIN # DEFINITION ALTERNATIVE DEFAULT SETTING 1 DCD 2 RX 3 TX 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI +5 VDC RI • IRQ 3 is assigned for COM2, IRQ9 is assigned for COM3, IRQ5 is assigned for COM4. All can be changed in CMOS setup. • Port COM2 is mostly suggested when a modem is to be connected. • DC supply to these ports is UPS supported. • Jumper selection: please refer to the description in Hardware details of this manual.
PARALLEL PORT LPT1 PIN ASSIGNMENT OF 25 PIN D SUB FEMALE CONNECTOR: EPP MODE PIN # SPP MODE 1 - STROBE -WRITE 2 D0 D0 3 D1 D1 4 D2 D2 5 D3 D3 6 D4 D4 7 D5 D5 8 D6 D6 9 D7 D7 10 - ACK INTR 11 BUSY -WAIT 12 PE NU 13 SLCT NU 14 - AUTO FEED -Datastb 15 - ERROR NU 16 - INIT NU 17 - SLCT IN NU 18 GND GND 19 GND GND 20 GND GND 21 GND GND 22 GND GND 23 GND GND 24 GND GND 25 GND GND • IRQ 7 is assigned for this port.
LAN PORT PIN ASSIGNMENT OF 8 PIN TELEPHONE JACK: PIN # DEFINITION 1 TD + 2 TD 3 RD + 4 NC 5 NC 6 RD 7 NC 8 NC • This port is defined as 100 base T or 10 base T LAN port. • This port is utilized by the system in pnp (Plug-N-Play) way, IRQ assigned is not fixed for this port. Most usual observation is IRQ 11.
PS/2 MOUSE PIN ASSIGNMENT OF 6 PIN MINI DIN JACK: PIN # 1 2 3 4 5 6 DEFINITION PMDAT NC GND VCC PMCLK NC AUDIO OUT PIN ASSIGNMENT OF 3.5 Ø STEREO JACK: CONTACT ON PLUG: TIP RING OUTER DEFINITION: R L GND MIC. IN PIN ASSIGNMENT OF 3.
CF CARD CONNECTOR l Accepts Compact Flash Memory Card type II TP-5700/5800 series Technical Manual 4 - 8
APPLICATION GUIDES POWER SUPPLY TO COM PORTS On the solder side of the main board, jumpers on JP13 and JP14 determine the +5V DC supplies to the devices connected to COM1/COM2 and COM3/COM4 separately. Refer to the hardware details for jumper settings. The total load supplied from the Jiva SL (TP5700) & Jiva EL (TP5800) series to all USB devices on 5 V DC is limited to be within 1 Ampere, and power to all other peripherals including keyboard, COM ports etc. on 5 V DC is also limited to be within 1 Ampere.
1 stop bit should be avoided. An index summary of such commands is tabulated at end of this chapter. CASH DRAWER The software command to open the cash drawer or the first cash drawer with the optional 2 in 1 cash drawer control cable is a hexadecimal code of <07> sent to COM1 port under the protocol of 9600bps, none parity, 8 data bits, 1 stop bit.
application program to COM1 under the protocol: 9600 bps, parity none, 8 data bits, 1 stop bit. • Change to power on only switch – the command string is <1B> <19> <01> or alternatively <1B> <00> <00> <00> <00> <00> <00> <18> in hexadecimal format. • Change to power on/off switch -- the command string is <1B> <19> <00> or alternatively <1B> <00> <00> <00> <00> <00> <18> <00> in hexadecimal format.
FORCED POWER OFF In case of serious system halt due to system resources conflict or any reason, the system could fail to power off through normal means. The Forced Power Off method is designed for such occasions. With the external power switch defined as power ON/OFF switch (default status), push down and hold this Power ON/OFF Switch. The system will be powered off within 10 seconds in this way.
to last for more than few minutes, it is advisable to turn off the system instead of using the battery up while repeatedly using it up reduces the battery life dramatically. The battery will undergo self-discharging over time even when not in use. A useful advice to preserve the battery at best condition is to regularly recharge the battery if the battery or the TP system with the battery is put in storage for a period of time.
Ÿ Ÿ To enable UPS function: <06> <16> <19> <1F> <05> or <1B> <00> <00> <00> <00> <18> <00> <18> To disable UPS function: <06> <16> <19> <1F> <04> or <1B> <00> <00> <00> <00> <18> <18> <00> UPS DETECTION FUNCTION In the Jiva SL (TP5700) & Jiva EL (TP5800) series products, when the system is working on UPS battery power, the status is indicated by LED and is detectable by software.
10 seconds after sending the query command and to send the other query command only after first response checked to avoid any possible ambiguity. POSIFLEX TOOLS In the preinstalled OS there will be a program group named Posiflex Tools if any of the PS2 interface touch panel, UPS battery is installed and the deluxe security device KP100. There will be a “Posiflex Touch Calibrator” and a “Posiflex Touch Manager” in this group for the PS2 interface touch panel.
TOUCH MANAGER This function allows the user to define the touch response as beep sound control and double click speed. Once executed, there will be several controller items as below. ENABLE TOUCH BEEP Clicking on this item alters the check status in the check box. When it is checked, every time the panel is touched, there will be a beep sound determined by parameters below this item.
at the very edge of screen display and making a movement to go outward from the screen like a real mouse does. EXIT Clicking on this item saves all the parameters and exits the program. POWER SWITCH MANAGER POWER SWITCH SETTING The function of the power switch that is at the lower part of the right side as viewed in desktop application can be defined here.
off command. However, this command must be engaged to turn the power off when the power switch is set to “ON Only”. SAVE AND EXIT Clicking on this item saves all parameter and exits the program. CANCEL AND EXIT Clicking on this item discards all parameter changes and exits the program. PROGRAMMABLE KEYBOARD STARTING THE PROGRAM This program applies only to the KP100 upgrade kit side mounted to a TP5700/TP5800 series.
bar turns into yellow to indicate that you are now editing the content of this particular key. COMMAND MENU Please remember that if the keyboard programming utility ends without any “Save” (to file) or “Write” (to keyboard) operation, every effort done in this utility will be washed away leaving no slightest trace. Please always “Write” to keyboard in order to “program” the KP100. Materials below help mastering this programming utility.
programmed to KP100, in application of KP100 when that key is pressed, it works as if those special keys on a standard keyboard were pressed as predefined. BREAK CODE – For programming function keys like “Shifts”, “Controls” or “Alts” in content for a key, its corresponding “break code” must be also programmed into the key content afterwards. Otherwise these function keys will act as if they are kept pressed for any other contents transmitted to host after it.
“Alt-num” approach. This means that, for example, when “A” is read, the scan codes for pressing and holding “Alt” key while pressing “6” and “5” keys of the numerical keypad consecutively are sent to the keyboard controller. Therefore, the data will not be misinterpreted regardless of the keyboard layout. ENABLE MSR TRACK 1 A tick in the check box enables the reading of track 1 data. Without this check, the data of track 1 on the MSR will be ignored.
default track 1 leading code is “%”; the default track 2 and track 3 leading code is “;”; the default ending code is “?”. INTERCHARACTER TRANSMISSION DELAY Usually, the processing algorithm and the keyboard data input buffer in an operating system are arranged in such a way that the system resources are preserved as much as possible while data input from the keyboard port presents no problem.
Usage of the Command Page Chapter Section / Subsection Open CR1 5-2 Application Guide Cash Drawer Open CR2 5-2 Application Guide Cash Drawer Drawer open sense 5-2 Application Guide Cash Drawer Main switch ON only 5-3 Application Guide Power On/Off Control External Power Switch / Main switch ON/OFF 5-3 Application Guide Power On/Off Control External Power Switch / Software power off 5-3 Application Guide Power On/Off Control Software Switch Off / Enhance forced power off 5-4 Appl
software control in the application program in consideration of the hardware upgrading. One easiest way to utilize the NVSRAM of a Jiva SL (TP5700) & Jiva EL (TP5800) system is through the use of appropriate software driver to simulate a disk drive. To have the NVSRAM work as a simulated disk drive, the user should first simply download from web page http://www.posiflex.com.tw/english/download.htm the file NDISK.
HARDWARE DETAILS MAIN BOARD COMPONENT SIDE JP18 JP22 JP24 JP23 KBMS1 AUDIO1 JP25 JP8 LAN1 U1 JP21 JP26 JP19 LPT1 D I M 1 D I M 2 VGA1 U2 PCI1 COM3 JP12 COM1 U11 L C D 1 U3 A1 CF1 B2 JP34 JP15 JP7 JP2 JP3 IDE2 IDE1 JP4 TP-5700/5800 series Technical Manual 6 - 1
SOLDER SIDE JP6 BAT JP9 JP16 +5V2 2 +5V JP13 TP-5700/5800 series Technical Manual 6 - 2 JP11 JP14
JUMPERS AND CONNECTORS ON COMPONENT SIDE Position AUDIO1 CF1 COM1 COM3 DIM1 DIM2 IDE1 IDE2 JP2 JP4 JP7 JP12 JP15 JP18 JP19 JP21 JP22 JP23 JP24 JP25 JP26 JP34 KBMS1 LAN1 LCD1 LPT1 PCI1 VGA1 Part Spec 3.5Ø Jacks CF Slot 2x D Sub 9M 2x D Sub 9M DDR Socket 184p DDR Socket 184p Slot 40p Slot 40p HDR 2x3 HDR 1x4 HDR 1x2 HDR 1x2 HDR 1x8 +L Switch HDR 1x3 Rt RJ11 Jack HDR 1x3 +L Socket 4p Socket 1x4 HDR 1x4 +L HDR 1x4 +L HDR 2x2 2x mini DIN 6p Composite Conn.
ON SOLDER SIDE Position BAT1 JP6 JP9 JP11 JP13 JP14 JP16 Part Spec Round Socket Mini HDR 1x2 Mini HDR 1x2 Mini HDR 1x3 Mini HDR 2x3 Mini HDR 2x3 Mini HDR 1x3 Usage CMOS BATTERY SOCKET VGA DC SUPPLY LAN Enable/Disable Control CMOS Data Control COM1/COM2 DC Supply Select COM3/COM4 DC Supply Select UPS Status JUMPER SETTINGS The “«” marks in the following tables denote the factory default settings.
COM3/COM4 DC SUPPLY SELECT STATUS OF JP14 ON SOLDER SIDE PIN 9 STATUS 1 – 3 short COM3 Pin9 connected to 5 V DC 3 - 5 short COM3 Pin9 connected as RI 2 – 4 short COM4 Pin9 connected to 5 V DC 4 - 6 short COM4 Pin9 connected as RI « « Please note that the 5 V DC supply should be selected only for supporting the Posiflex serial devices that are designed to be powered from this source. Whenever such Posiflex device is to be removed from this port, the 5 V DC supply must be deselected.
VGA PORT DC POWER ENABLE/DISABLE STATUS OF JP6 ON SOLDER SIDE VGA PORT Short 12 V DC ENABLED (For LM6001 or TM6001) Open 12 V DC DISABLED PS2 MOUSE SIGNAL LOOP STATUS OF JP4 MOUSE SIGNAL « Through Touch Controller Li BATTERY CURRENT MEASUREMENT STATUS OF JP12 Li BATTERY Short Connected Open Disconnected « TOUCH SIGNAL SETTING STATUS OF JP2 TOUCH SIGNAL 1 – 3, 2 – 4 Short COM4 PORT 3 – 5, 4 – 6 Short N.A.
USB MSR CONTROL BOARD (UMSRCPU) JUMPER SETTING IN JP1 2 12 1 11 CN2 CN3 CN1 JP1 AT43301 U3 U5 UMSRCPU-D T1 Enable -> 1&2 = Short ；T1 Disable -> 1&2 = Open T2 Enable -> 3&4 = Short ；T2 Disable -> 3&4 = Open T3 Enable -> 5&6 = Short ；T3 Disable -> 5&6 = Open ISO MSR -> 7&8 = OPEN；JIS2 MSR-> 7&8 = Short ALT+NUM ON -> 9&10 = Open；ALT+NUM OFF -> 9&10 = Short Leading Code Enable -> 11&12 = Open；Disable -> 11&12 = Short TP-5700/5800 series Technical Manual 6 - 7
SERVICE AND SPARE PARTS SERVICE GUIDE Reference to the Posiflex Jiva Instructional Assembly & Disassembly Video CD could help instant comprehension on operations below. SIDE MOUNT UPGRADE KIT The available side mount upgrade kits include KP100 and SD100. The KP100 is a larger unit with always a 40 key programmable keypad. The SD100 is a smaller unit without this keypad. Various function kits besides the keypad can be applied in the upgrade kit.
edge of the main unit and fasten the two screws with washer as indicated in the picture. Route the cable with or without an extension cable through the side of the cable cover to proper port. Break the obstructing sidewall of the cable cover at the cable entrance to the connector area. Side Mount Screw REAR TOP MOUNT UPGRADE KIT The upgrade kit that can be mounted on rear top of the whole Jiva series (all TP series) is PD302, a 2 by 20 LCD customer display. Separate the main unit from its stand assembly.
4. Guidance for future un-installation: Please always use a screw driver to release the metal hook before removing PD302 from the ventilation holes. OPEN THE MAIN UNIT Opening the main unit is a tricky and difficult job. The first and the easiest step is to disconnect power and every cable (including the LED cable) and separate the main unit from the paddle assembly. Unlock and open the cable cover.
cover plate, remove the cover plate, and remove the riser card from the opening before completely removing the LCD panel assembly. 4 screws on riser card plate 3 screws each side Riser card However, if the mechanical structure of the system is already of a newer version that we call it as snap-on structure and utilizes minimal number of screws in assembly as in pictures below a lot of unscrewing operations are eliminated.
Unscrew totally 9 screws (2 on top, 4 on Don’t touch circled screws! bottom, 2 each on either side) on the cover plate of the steel box revealed after removal of LCD panel assembly. Do not loosen any of the 3 screws on each side that the screw heads are within the small circular openings of the cover plate. Just as in the previous section, for the snap 1. Remove on structure version the operation is also greatly this screw simplified. Remove the only screw as indicated and 2.
rubber sleeve. Then insert the copper sleeve from the bottom of the bracket so that the screw and washer can fix the bracket from top. REPLACE MAINBOARD After removal of HDD or HDD and the CD ROM adaptor card PST069 for system since revision D, please remove the 4 (round head) screws at the bottom of the connector panel and the 8 screws holding the mainboard to the back cover assembly. Disconnect the exhaust fan and raise the mainboard up along the HDD support posts.
SPARE PARTS LIST The column “Pos.” in the list below refers basically to the ID numbers indicated in the Assembly Drawing. However, if this column is not available, it refers to a packaging item. The column “S.” indicates the alternative selections available for that position. Please pay particular attention in making selection among the alternatives when there are some clues given in the column “Description” to indicate its relation with other items in the system.
2 20953002011 Pos. S. Part Number 105 1 36202006000 DTP6KHDDKITASY 106 1 16200112000 MTP6M-112 107 1 1 108 2 109 1 1 2 110 3 4 3628200010 46280244200 46280254200 20833200000 HCT-50TC-8 36282002001 36282002002 HDD IBM 20GB or up for TP-5800 series only Description HDD Suspension Kit (incl.
113 1 16200011300 MRUBFT19*5 Pos. S.
3 46281214100 TP076-CPT Pos. S. Part Number 124 20862033400 CCBLA-334 7 Wire Touch Panel Extension Cable for F touch 1 20862029000 CCBLA-290 Inverter Cable for single backlight LVDS LCD 12.1” LG (LP121X04) 2 20862031600 CCBLA-316 Inverter Cable for 15” LCD of source AU/CPT (M15DXN05/CLAA150XG01) 20811156201 LCD Panel 15” source AU (model: M15DXN05) 20811157201 LCD Panel 15” source CPT (model: CLAA150XG01) 20811121101 LCD Panel 12.
Pos. S. Part Number (128) 4 36282022000 Description Touch Panel & Support Frame Assembly 12.1”, Snap on Structure source Touch: F w/TP068A; for LCD: LG (single back light) (model: LP121X04) LVDS 1024 x 768 1 46209202000 TP069 External CDROM Adaptor Card (TP069) for TP-5800 series only 131 1 36201005000 16200110020+2X MSCRW#6-8+P Cable Exit Cover Plate w/ 2x Screws 132 1 20901302032 CBT3.0VLI Li-Battery CR2032 129 S.
S. Part Number 8 9 10 11 12 1 1 1 20868200500 20868300500 20868400500 20868500500 20868600500 16200511160 16200541050 16280900010 Description Power Cord for Europe for TP5800 series Power Cord for Japan for TP5800 series Power Cord for S.A. for TP5800 series Power Cord for U.K. for TP5800 series Power Cord for U.S.A.
108 101 102 103 104 105 106 132 109 110 111 107 112 131 113 116 118 133 119 129 120 135 121 134 136 128 127 126 125 124 123 122 TP-5700/5800 series Technical Manual 7 - 13
