Technical data

Continent
Europa
USA & Canada
Australien
Mains voltage (V)
and frequency (Hz)
220V - 230V, 50Hz
115V, 60Hz
240V, 50Hz
Mains fuse
230V
115V
230V
SAFETY INSTRUCTIONS
General safety instructions
Do not remove the cover or back. No user serviceable parts inside; refer servicing to qualified
personnel. To reduce the risk of fire or electrical shock, do not expose this appliance to rain or
moisture, direct sunlight or excessive heat from sources such as radiators or spotlights. The free
flow of air inside and around the unit must always be ensured.
Initial operation
Prior to the initial operation of the unit, the appliance, its accessories and packaging must be
inspected for any signs of physical damage that may have occurred during transit. If the unit has
been damaged mechanically or if liquids have been spilled inside the enclosure, the appliance may
not be connected to the mains or must be disconnected from the mains immediately!
If the unit is damaged, please do NOT return it to MUTEC GmbH, but notify your dealer and the
shipping company immediately, otherwise claims for damage or replacement may not be granted.
The unit has been designed for operation in a standard household environment. Before you at-
tempt to operate the unit, please make sure that your local voltage matches the voltage required
by the unit! The fuse holder can be found on the rear of the unit, just below the compartment
marked 230 V (115 V). Use the fuse holder to adjust the required mains voltage.
Ex factory, the unit is equipped with a 230-V mains fuse. If the unit needs to be adjusted to 115 V, the
fuse must be replaced as described in the appendix, section Replacing the mains fuse.
Please use the enclosed power cord (see packaging) to connect the unit to the mains. Switch the
unit off before you attempt to connect it to the mains. Connect the power cord to the unit, then
to a standard 3-pin mains outlet. To draw the power cord, never pull on the cable but on the mains
plug!
The unit must be grounded during operation!
The mains socket wiring is described in the appendix, section Wiring of connectors.
Declaration of Conformity
We herewith confirm that the product complies with the European Commissions standards on
electromagnetic compatibility.
Interference emission: EN 50081-1, 1992
Resistance to interference: EN 50082-1, 1992
Presupposed as operation condition is that all outputs are connected with high-quality and good
shielded cables.
WARRANTY REGULATIONS
§1 Warranty
MUTEC GmbH warrants the flawless performance of this product to the original buyer for a period of two (2) years from the date of purchase. If any failure occurs
within the specified warranty period that is caused by defects in material and/or workmanship, MUTEC GmbH shall either repair or replace the product free of charge
within 30 days. If the warranty claim proves to be justified, the product will be returned freight prepaid by MUTEC GmbH within Germany. Outside Germany, the
product will be returned with the additional international freight charges payable by the customer. Warranty claims other than those indicated above are expressly
excluded.
§2 Warranty transferability
This warranty is extended exclusively to the original buyer who bought the product from a MUTEC GmbH specialized dealer or distributor, and is not transferable
to anyone who may subsequently purchase this product. No other person (retail dealer, distributor, etc.) shall be entitled to give any warranty promise on behalf of
MUTEC GmbH.
§3 Warranty regulations
To be protected by this warranty, the buyer must complete and return the warranty registration card to MUTEC GmbH within four (4) weeks of the date of pur-
chase. Failure to return the card in due time (date as per postmark) will void any extended warranty claims.
The serial number indicated on both the returned product and warranty registration card must be identical, otherwise the product will be returned freight col-
lect to the consignor.
The product/warranty registration card must be accompanied by a copy of the original invoice issued by the MUTEC specialized dealer or distributor.
The product must be returned in its original shipping carton or a packaging of similar design and quality. MUTEC GmbH assumes no liability for any damage to or
loss of the product during transit.
§4 Limitation of warranty
Damages caused by the following conditions are not covered by this warranty:
Damage caused by normal wear and tear (e.g. potentiometers, faders, switches, buttons, connecting elements, printed labels, cover glasses and similar parts).
Functional failure of the product caused by improper installation (please observe CMOS components handling instructions!), neglect or misuse of the product
(e.g. failure to operate the unit in compliance with the instructions given in the user or service manuals).
Damage caused by any form of external mechanical impact or modification.
Damage caused by the users failure to connect and operate the unit in compliance with local safety regulations.
Damage caused by force majeure (fire, explosion, flood, lightning, war, etc.).
Consequential damages or defects in products from other manufacturers as well as any costs resulting from a loss of production.
Repairs carried out by unauthorized personnel will void the warranty. Always ensure proper ventilation of the product. When installing the product in a rack, leave
one unit of rack space free both above and below the unit for ventilation!
§5 Repairs
To obtain warranty service, the buyer must call or write to MUTEC GmbH before returning the unit. All inquiries must be accompanied by a description of the prob-
lem. In case of a functional failure please contact:
MUTEC Gesellschaft für Systementwicklung und Komponentenvertrieb mbH
Siekeweg 6/8  12309 Berlin  Fon 030-746880-0  Fax [phone]  [e-mail]  www.mutec-net.de
MUTEC GmbH assumes no liabilit y for any incorrect information given in this manual. Please note that
all software/hardware product names are registered trademarks of their respective owners. No part of
this manual may be reproduced, copied or converted to a machine-readable form or electronical media
without a written permission of MUTEC GmbH. We reserve the right to change or improve our products
without notice. © MUTEC GmbH 2000
This symbol, an exclamation mark inside a triangle,
alerts you to important operating or safety instruc-
tions in this manual.
This symbol, a flash of lightning inside a triangle,
alerts you to the presence of uninsulated dangerous
voltage inside the enclosure - voltage that may be
sufficient to constitute a risk of shock.
R I S K O F
ELECTRICAL SHOCK!
C A U T I O N