Operation Instructions Rockhopper 3 Extreme English
Operation Instructions Rockhopper 3 Extreme English 2 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme English COPYRIGHT NOTICE COPYRIGHT © 2009 Mutoh Europe N.V. All rights reserved. This document may not be reproduced by any means, in whole or in part, without written permission of the copyright owner. This document is furnished to support the Mutoh Rockhopper 3 Extreme series Printer.
Operation Instructions Rockhopper 3 Extreme English 4 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme English TABLE OF CONTENTS 1 Safety Instructions ................................................................................ 7 1.1 1.2 1.3 1.4 1.5 1.6 2 Product Overview ................................................................................ 13 2.1 2.2 3 Done by end user ................................................................................................ 29 Done by authorised Mutoh technician .........................................
Operation Instructions Rockhopper 3 Extreme English This page is intentionally left blank 6 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 1 : SAFETY INSTRUCTIONS 1 SAFETY INSTRUCTIONS 1.1 REGULATIONS The CE marking is a mandatory European marking for certain product groups to indicate conformity with the essential health and safety requirements set out in European Directives.
Operation Instructions Rockhopper 3 Extreme CHAPTER 1 : SAFETY INSTRUCTIONS 1.2 MANAGING VOC’S When Mutoh printers with (low)-Solvent inks are used, volatile organic compounds (VOCs) will be released. In order to protect human health and the environment, VOCs must be managed. This means VOCs need to be controlled and compliance with all local, state and federal environmental, occupational health and safety regulations on VOCs in the atmosphere and in the workplace is needed.
Operation Instructions Rockhopper 3 Extreme CHAPTER 1 : SAFETY INSTRUCTIONS 1.4 WARNING, CAUTIONS AND NOTES Safety terms in this manual and the contents of warning labels attached to the printer are categorized into the following three types, depending on the degree of risk (or the scale of accident). Read the following explanations carefully and follow the instructions in this manual. Safety terms Important Caution Notes Details Must be followed carefully to avoid death or serious bodily injury.
Operation Instructions Rockhopper 3 Extreme CHAPTER 1 : SAFETY INSTRUCTIONS • Do not cover the ventilation hole of your machine with cloth, such as a blanket or table cloth. Doing so could obstruct ventilation and cause fire. • Do not insert or drop metal or inflammable objects into openings, such as ventilation outlets. Doing so may result in electrical shock and fire. • Do not touch the media guide during printing. It is hot and may cause a burn.
Operation Instructions Rockhopper 3 Extreme CHAPTER 1 : SAFETY INSTRUCTIONS 1.6 WARNING LABELS The handling, attachment locations, and types of warning labels are explained below. Warning labels are attached on areas which require attention. Read and understand the positions and contents thoroughly before performing your work. 1.6.1 Handling the warning labels Be sure to note the following when handling the labels. • • • Notes Make sure that all labels can be recognized.
Operation Instructions Rockhopper 3 Extreme CHAPTER 1 : SAFETY INSTRUCTIONS 1 2 4-10 5 6-9 7 3 8 1.6.2.2 Location and types of warning labels on back part. No. Type 3 CAUTION THISUNITHASTWOPOWERSUPPLYCORDS, WHENWiNDING UNITISPROVIDED. TOREDUCETHERISKOFELECTRICAL SHOCK, DISCONNECTALLPOWERSUPPLYCORDS BEFORESERVICING. 4 12 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 2 : PRODUCT OVERVIEW 2 PRODUCT OVERVIEW 2.1 PART NAMES AND FUNCTIONS Part names and functions are explained below. 2.1.1 Front No Name Function Heater plate Supports and heats the media during printing. 2 Front cover Keeps the operator safe from the drive parts of the printer while it is operating.
Operation Instructions Rockhopper 3 Extreme CHAPTER 2 : PRODUCT OVERVIEW 2.1.2 Rear No 1 2 3 4 5 6 7 8 9 10 Connection Ethernet connector Card reader slot SmartChip label HardDisk bracket cover Centronics connector Foot switch connector Power inlet Environmental label DB-25 connector ID label 14 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 2 : PRODUCT OVERVIEW 2.1.3 Heater system Under the print platforms, heater strips are attached. Each heater can be set separately. Please refer to the table below to know the function of each heater.
Operation Instructions Rockhopper 3 Extreme CHAPTER 2 : PRODUCT OVERVIEW 2.1.4 Operation panel 2.1.4.1 Keys No 1 2 3 4 5 6 Name [POWER] key [F1] key [F2] key [F3] key [F4] key [MENU ↑] key 7 [MENU ↓] key 8 [ENTER] key Normal Switch the printer ON and OFF Executes the function assigned to F1. Executes the function assigned to F2. Executes the function assigned to F3. Executes the function assigned to F4. Changes the LCD monitor display to the setup menu status.
Operation Instructions Rockhopper 3 Extreme CHAPTER 2 : PRODUCT OVERVIEW 2.1.4.2 LCD and LED’s No 10 Name LCD monitor Colour - Status - 11 POWER lamp Green 12 ERROR lamp Red ON OFF Flashing 13 DATA lamp Orange 14 MEDIA SET lamp Orange OFF ON Flashing OFF ON OFF 15 ROLL lamp Orange 16 SHEET lamp Orange 17 HEATER lamp Orange ON OFF ON OFF ON Flashing OFF Function The monitor displays the operation status and error messages of the printer. The printer is on. The printer is off.
Operation Instructions Rockhopper 3 Extreme CHAPTER 2 : PRODUCT OVERVIEW 2.2 INSTALLATION REQUIREMENTS An Authorized Mutoh technician will install your unit and will make the printer ready for its first job. A room which meets the environmental and space conditions should be foreseen by the user. Area 12.7m² (144ft²) or larger. Frontage of 4.7m (15.7ft) or greater.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 3 BASICS 3.1 POWERING ON CYCLE Caution BEFORE POWERING ON THE PRINTER, MAKE SURE THAT THE WASTE BOTTLE IS INSTALLED AND THAT THE WASTE TUBES ARE CONNECTED TO THE WASTE BOTTLE. Power ON the printer according to the procedure below: Step 1 : Press the [POWER] key of the operation panel. The POWER lamp of the operation panel will light (green). Step 2 : The printer will ask if you want to clean the wipers.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS Step 6 : Make the correct settings and press the [F4]-key to start the media initialization. Step 7 : If everything is done correctly, the following screen should appear.. Notes IF THERE ARE ANY PROBLEMS DURING THE INITIAL START-UP OPERATION, THE PRINTER WILL DISPLAY A MESSAGE ON IF THE OPERATION STOPS, REFER TO THE OPERATION PANEL, AND THE OPERATION MAY STOP. "TROUBLESHOOTING", AND TAKE THE APPROPRIATE ACTIONS.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 3.3 LOADING MEDIA 3.3.1 Loading roll media Please refer to the User’s Guide of the Unwinder/Winder 100 or the T- winder to know how to load roll media. 3.3.2 Loading sheet media To load sheet media, follow the steps below. Step 1 : Power ON the printer. Step 2 : Unload media if necessary. Step 3 : Be sure that the pressure rollers are raised before loading sheet media.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS Step 7 : Make measurement settings in following menu: SetupMenu (1/7) ► MediaSet [F4] ► SheetSize Menu Choice F1 Auto Description Media measurement sequence ► REAR – RIGHT – LEFT – TOP Media measurement sequence ► RIGHT – LEFT – TOP Media orientation F2 Length Media measurement sequence ► RIGHT – LEFT – TOP Media orientation F3 Width Step 8 : Close the front cover. Step 9 : Start media initialisation.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 3.4 REPLACING INK CASSETTES 3.4.1 Ink cassette behaviour Please read this chapter thoroughly to know the behaviour of a Mutoh ink cassette used with the Rockhopper 3 series printers. An ink cassette contains 220 or 440 ml of ink. The amount of ink left in the cassette is monitored by the smart chip installed on the cassette.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 3.4.2 Types This printer is designed to use Mutoh Eco-Solvent Ultra Ink cassettes. If using other ink cassettes ► ► ► ► Warranty will be void. Prints may not reach the expected quality level. Heads can be damaged. Printer will not recognize these cassettes when inserting (smart chip) Please refer to the latest price list to know the available ink and cleaning cassettes for the Rockhopper 3 Extreme, and for the latest price and part numbers.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 3.5 REPLACING CUTTING BLADE Read following information on when and how to replace the cutting blade. 3.5.1 Replacement time Replace the cutting blade under the following conditions: ► ► Media cannot be cut clearly. When the cut edge is blurred. 3.5.2 Replacement procedure Follow the steps below to replace the cutting blade. Step 1 : If the printer is powered ON, verify following items: Printing or other operations are not performed.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 3.6 REPLACING THE WASTE BOTTLE 3.6.1 Replacement Time Replace the waste liquid tank when following message is displayed. 3.6.2 Replacement Procedures Follow the steps below to empty the waste bottle. Step 1 : Open the lid and remove the waste bottle. Step 2 : As soon as the waste bottle has been removed, the following message appears: Step 3 : Pour the waste liquid in another bottle and dispose it according to the local regulations.
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 3.7 TRANSFER AND TRANSPORTATION This section explains transferring and transporting the printer. 3.7.1 Transferring the printer Following are instructions for transferring the printer. (1) Before the transfer If you are using the stand, follow the steps below to transfer the printer. Step 1 : Make sure the printer is turned off. Step 2 : Make sure the head is in the right edge position (capping position).
Operation Instructions Rockhopper 3 Extreme CHAPTER 3 : BASICS 28 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4 PERIODICAL MAINTENANCE 4.1 DONE BY END USER This section describes the periodical services required for this machine. The periodical services ensure stable printout quality of the machine. In the periodical services, some service parts may be checked, cleaned, or replaced. Perform periodical inspections according to the table below.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.1 Weekly Maintenance 4.1.1.1 Step 1 : Clean the edges of the caps and the area around the caps Power ON the printer and go to the “WiperClean-Menu”, DON’T press enter when in it. This will cause the unlocking of the carriage. Step 2 : Clean the edges of the caps with the cleaning swab, if necessary use some Eco solvent cleaning liquid. Step 3 : Clean the area around the caps with a polyknit wiper.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.1.2 Cleaning around the bottom of heads Step 1 : Open the left maintenance covers by removing the four screws. Step 2 : Power ON the printer and go to the “WiperClean-Menu” DON’T press enter when in it. This will cause the unlocking of the carriage. Step 3 : Slide the carriage into the left maintenance area.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.1.3 Step 1 : Cleaning the wipers Power ON the printer and go to the “WiperClean-Menu”, DON’T press enter when in it. This will cause the unlocking of the carriage. Step 2 : • Clean the wipers (3) with a polyknit wiper (2), use some Eco solvent cleaning liquid to remove drops of ink. Caution It is recommended to wear gloves as shown on the picture below.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE Monthly maintenance 4.1.2.1 Replacing the wipers Step 1 : Power ON the printer and go to the “WiperClean-Menu”. This will cause the unlocking of the carriage. Step 2 : Slide the carriage to the left side of the machine. Step 3 : Remove the old wipers with a pair of tweezers Step 4 : Before inserting a new wiper, moisten the wiper with Eco-Solvent Ultra Cleaning Liquid.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.2.2 • Replacing the sponge in the spitting box. Notes Use gloves and tweezers to change the absorbent in the flushing box. Step 1 : Go to the WiperClean menu and DON’T press enter when in it. Going to the WiperClean menu will unlock the head Step 2 : The carriage moves to the waiting position for replacing the flushing sponge. Step 3 : Remove the old absorbents with tweezers.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.3 Every 6 months maintenance 4.1.3.1 Step 1 : Change upper sponge at back of the capping station. Go to the WiperClean menu and DON’T press enter when in it. Going to the WiperClean menu will unlock the head Step 2 : Remove the two screws fixing the sponge (1). 1 = Screws fixing the sponge (1) Step 3 : Replace the sponge and tighten it again to the plate with the two screws.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.4 Cleaning You need to clean the printer periodically to keep it in best working condition. • • • • • Important Do not insert or drop metal or inflammable objects into openings, such as ventilation outlets. Doing so may result in electrical shock and fire. Stop using your printer if a liquid is spilled into it. This may cause electrical shock or fire.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.4.2 Cleaning the inside of the printer (1) Cleaning frequency Clean once a month. (2) Cleaning procedure The following are instructions for cleaning the inside of the printer. Follow the steps below. Step 1 : Open the front cover. 1 Step 2 : Front Cover Use a soft brush to carefully clean away any dust or dirt on the pressure rollers. Notes Do not blow off media dust inside the printer using an air dusting machine.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.1.4.3 Head cleaning If printouts become faint or partially missed, perform head cleaning to clean the surface of the head and the nozzles. Follow the steps below to perform head cleaning. Step 1 : Make sure that the state of the product is normal. Step 2 : Refer to "TestPrinting" to perform nozzle check printing. Step 3 : Check if the print head, referring to the diagram below.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE 4.2 DONE BY AUTHORISED MUTOH TECHNICIAN An Authorized Mutoh technician should check and replace some components of your printer on frequent base (every 6 and 12 months). Be sure to remind your distributor when the replacements should be done. It is very important not to skip a maintenance intervention in order to maintain constant print quality and to keep your warranty.
Operation Instructions Rockhopper 3 Extreme CHAPTER 4 : PERIODICAL MAINTENANCE This page is intentionally left blank 40 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 5 PREPARATIONS BEFORE PRINTING 5.1 USING MEDIA This section describes details on available media for the printer. 5.1.1 Media range Please refer to Mutoh’s website (www.mutoh.eu or www.mutoh.be) for the media compatibility lists for all our products.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 5.1.2 Cautions on handling media When you handle media, please pay attention to the following: • Use recommended media in an appropriate environment. Following are the appropriate temperature and humidity ranges for printing. Recommended working environment Rate of change Temperature 20-30°C Within 2°C per hour Humidity 40% to 65% Within 5% per hour • Do not use creased, damaged, torn, curled, or wrapped media.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 5.1.4 The printing area The printing area is shown below. (1) Roll media (2) Sheet media 43 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 5.2 SET THE CORRECT DISTANCE ADJUST (STEP) Obtaining constant printing quality on a wide-format Piezo inkjet printer is not only determined by the working environment, the RIP, the profiles, the inks and the media which are used. One of the key factors for obtaining constant output quality is the correct distance adjustment, also called “step”, on your Mutoh inkjet printer. 5.2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 5.2.2 How to determine and change the step Step 1 : Power ON the printer. Step 2 : Load the media to print on. Notes BE SURE TO TIGHTEN THE MEDIA TO THE WINDER 100 BEFORE SETTING THE STEP. THIS BECAUSE THE STEP WILL BE DIFFERENT WHEN PRINTING ROLL-TO-SHEET THAN WHEN PRINTING ROLL-TO-ROLL. Step 3 : Perform a NozzleCheck to be sure all nozzles are present. If not, perform the necessary cleanings.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING Step 7 : Step is too small ► overlap visible between passes Step is too big ► gap visible between passes Step 8 : Change the step if necessary. ▼ ▼ Step 9 : Print the test pattern again until no gap or overlap is visible anymore. 5.2.3 How to change the step on the fly. Step 1 : Press while printing. Step 2 : Press or to change the step. 46 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 5.3 I² TECHNOLOGY Without weaving ON, an image is completed (formed) by printing a series of complementary rectangular shaped stripes (bands, swaths, passes). Inherent to classic inkjet printing is that ink drying effects, stepping mismatch, miss firing nozzles show up in the printed image via ink bleeding and various types of banding.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING Weaving method Sign / Quality User Tip Preferred setting for signage/poster applications containing big areas with solid colours or critical gradients and for photo quality output on coated media. (small loss of speed in 2 pass modes) Print Modes Supported 720x720 540x720 Picture / Speed Stitch Creates a fine print swath overlap. Mildly improves print quality versus “Off” setting.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 5.4 PRINTING FLOW The following flowchart gives you a view on which steps should be taken to make a print. This is a very short summary of what should be done. SELECT MEDIA (Refer to the media compatibility lists on www.mutoh.
Operation Instructions Rockhopper 3 Extreme CHAPTER 5: PREPARATIONS BEFORE PRINTING 50 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6 PRINTER MENU 6.1 HOW TO WORK IN THE MENU Please find below all necessary information on how to switch, select and cancel menu items. 6.1.1 Main screen When powering ON the printer, it will (when no errors occur) start up in its main screen. The function of each key is explained below.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.1.3 Changing between the screens To change the printer status, follow the steps below. 6.1.3.1 From main screen to menu screen Press either screen 1/7 – 7/7 6.1.3.2 or on the operation panel when the printer is in the main screen to go to menu From menu screen to main screen To switch from a menu screen to the main screen, following actions can be taken: • • Press the [CANCEL] key on the operation panel.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.2 OPERATION PANEL IN STANDBY MODE This section describes functions operated on the operational panel when the printer is in the normal status. 6.2.1 [F1] – Feeding, Cutting media and Step Adjust When you want to feed media forward or backward, follow the steps below: Step 1 : Verify the following regarding the condition of the printer. I) It is not currently printing Step 2 : Press the [F1] key of the operation panel.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU Step 2 : Press the [F2] key of the operation panel. I) To shift to the cleaning menu. Step 3 : Press the [F1] key or the [F2] key on the operation panel.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.2.3.2 Activate/ deactivate heaters. In the second menu, press the [F1] key to activate or deactivate all heating elements. In case the heating elements are activated, the display will mention “SET OFF”. By pressing the [F4] key you can deactivate the heating elements. The display will mention “SET ON”. In case the heating elements are deactivated, the display will mention “SET ON”.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.3 OPERATION PANEL DURING PRINTING When sending a file to your printer, following messages can be displayed. 6.3.1 When heaters are not ready When the heaters are not reached their target temperature, the following screen will be displayed. Still, it is possible to start the print. However, the heater will continue to warm up in order to reach the requested temperature. Step 1 : Press the F3 key to ENTER the HeaterStatus menu.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.3.2.2 [F2] - Cleaning While printing, it could be possible that some nozzles drop out, in that case, perform a little, normal or powerful cleaning. Please follow the steps below to perform a cleaning. When there are some missing nozzles, a cleaning should be done. Depending on the quantity of missing nozzles and which head, a little, normal or powerful cleaning on head 1-2, head 3-4 or ALL could be done.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.3.2.4 [F4] - Loading ink volume during printing It is possible to load ink volume to the printer during printing. There are two possible scenarios: • SmartChip management system is not empty yet and the printer keeps printing. Press the F4 key to load ink volume. • SmartChip management system is empty and the printer stops printing but does NOT cancel the print. The following message will appear Press the F4 key to load ink volume.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.3.2.5 Menu ▼ and ▲ During printing, extra information about the current job is available. Use the menu UP and DOWN keys to browse through these menus. 1) Menu 1/4 Standard menu during printing. It is only possible to cancel a print in this menu! 2) Menu 2/4 and 3/4 Two situations are possible: • Length information is not provided with the job. The printer cannot know progress and remaining time.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.4 OPERATION PANEL AFTER PRINTING The operations performed after printing, are described here. 6.4.1 Cut off media with the printer knife The media cutting procedure is described below. Roll media is automatically cut after printing when "Auto" is set on the cut media menu and roll media has been set.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.4.2 Manually cut off media This section explains how to cut the media manually. When "Manual" is set in the media cut menu, the media can be cut manually. Cut the media according to the following procedure. Step 1 : Feed media to the desired position using the [F3] and [F4] key. Step 2 : Cut the roll media following the cutting groove. 61 AP-77150 – Rev. 2.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU 6.5 MENU OVERVIEW (1/7 – 7/7) SetupMenu 1/7 Ink Status/ Chipstatus Origin Set (1/1) Top Bottom Left Right Test Print (1/2) Setup Nozzle Check Adj. Uni-D Adj. Bi-D Palette Maintenance Dist.
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU (4/5) (2/2) Direction (5/5) (1/1) Repeat Prn (1/1) HeadSpeed (1/1) Weaving (1/2) (2/2) ScanWidth Command (1/1) Step (1/1) Resolution (1/2) (2/2) Layout Function (1/1) (1/1) OnlineTimer Joint (1/1) CutPosition (1/1) CMY > K (1/1) (1/1) 1080 x 2160 Diag 2160 2880 x 1440 1440 x 2880 Diag 2880 UniDir BiDir Count IntervalTime Normal Fine Sign/Quality Picture/Speed Stitch Classic OFF DataWidth MediaWidth FullWidth 4
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU SetupMenu 4/7 Utility (1/3) (2/3) (3/3) Initial (1/3) (2/3) (3/3) ErrorDisp (1/1) MediaDet, (1/2) OnCleaning (2/2) (1/1) MediaWidth Prn + Wipe Smart Top (1/1) AutoCleaning (1/1) CapCycle SlantCheck (1/1) RemPanel (1/1) RemoteConn (1/1) All (1/1) MediaSet (1/1) PrintMode (1/1) Command (1/1) LayOut (1/1) Function (1/1) RollSetup (1/1) Centro (1/1) Network (1/1) Utility (1/1) OFF ON Normal OFF TakeU
Operation Instructions Rockhopper 3 Extreme CHAPTER 6: PRINTER MENU SetupMenu 5/7 DataDump (1/1) InkManager (1/2) (2/2) Start/End All HeadWash (1/1) Discharge (1/1) InkLoad (1/1) InkChange (1/1) LongStore (1/1) InkSupply (1/1) ChipMgr (1/1) ColorMode** (1/1) NO YES Pump1 Pump2 ALL Pump1 Pump2 ALL NO YES NO YES ON OFF Printer* Cassette 2*4_symm 1*6 1*8 2*4_1C1H (*) For future use only. (**) Only visible when printer mode is activated in the ChipMgr. menu. SetupMenu 6/7 H.
