Operation Manual

without pressing the mentioned but-
ton.
Adjusting the footrest (m)
· If you wish to adjust the foot rest, move
the plastic knobs (L+R) under the foot
rest towards you simultaneously and
move the foot rest to the desired posi-
tion.
Adjusting the seat depth (m)
· To be able to adjust the seat depth,
you must first remove the cap from the
buggy.
· In order to adjust the seating depth,
it is best to first undo the velcro at the
back of the pushchair seat and tem-
porarily remove the rubber bands from
around the knobs.
· Then push the knobs (L+R) inwards and
turn through 180º. Move the back of
the seat forwards to increase the seat-
ing depth.
! Do not allow fabric to become jammed
in the adjustment mechanism, this may
block the mechanism.
Placing your child in the Deluxe Seat
! Use a harness as soon as your child
can sit unaided.
· Place your child in the seat and make
sure that the legs of your child are on
both sides of the crotch strap.
· Take care that the seat as well as the
footrest is adjusted correctly to the
length of your child.
· The pushchair has a 5-point safety har-
ness. You operate the safety harness by
fixing all the plastic parts.
· The safety harness can be adjusted by
moving the plastic parts over the belts
and placing them in the desired posi-
tion.
Maxi Cosi Car Seat (0-9 months)
Placing the Maxi Cosi on the frame (n)
· Place the Maxi Cosi adapter set in the
universal fixation points of the frame.
! Place the adapter with R on the right
side and place the adapter with L on
the left side.
· Push the Maxi Cosi down until it firmly
clicks. Make sure that the Maxi Cosi is
fixed properly and that the red surfaces
in the universal fixation points are fully
covered.
Removing the Maxi Cosi from the frame
· Push the light blue buttons that are on
the sides of the Maxi Cosi and lift the
Maxi Cosi off from the adapters.
· Remove both adapters by performing the
same actions as when removing the
Deluxe seat (see “Removing the seat”).
Traveller Car Seat (0-9 months)
Placing the Traveller on the frame(o)
· Place the adapter set in the universal
fixation points of the frame.
! Place the adapter with R on the right
side and place the adapter with L on
the left side.
· Place the Traveller backwards on the
frame. Lock the Traveller by moving the
carrying handle backward. Ensure that the
Traveller is fixed correctly by trying if the
car seat can be removed from the frame.
Removing the Traveller from the frame
· Turn the lever to adjust the carrying han-
dle of the traveller and push the carry-
ing handle in the vertical position.
· Lift the Traveller by the carrying handle
of from the adapters.
· Remove both adapters by performing the
same actions as when removing the
Deluxe seat (see “Removing the seat”).
Graco Autobaby (2,3-10 kg and < 73 cm)
Graco Snugride (5-22 lbs and < 29 in)
Graco Logico S (2,3-13 kg and < 80 cm)
Graco Safeseat (5-30 lbs and < 32 in)
Placing the Graco on the frame (p)
· Place the adapter in the universal fixa-
tion points of the frame.
· Place the Graco on the adapter and push
it down until it firmly clicks. Pull up on
the Graco to be sure it is latched firmly
onto the adapter.
Removing the Graco from the frame
· Squeeze the release handle at the back
of the Graco and lift it off the
adapter.
· Remove the adapter by performing the
same actions as when removing the
Deluxe seat (see “Removing the
seat”).
English
20