MV900 User Manual
Table of Contents Table of Contents 1 1. Introduction 2 2. Function Modes and Compatibility 2 3. Charging 3 4. Turning on the MV900 3 5. Basic operations 3 6. Headset mode (Privacy mode) 3 7. Using as a USB Speakerphone 3 8. Using with Desktop Phones 3 9. Using as a Bluetooth Speakerphone with Cell Phones 4 1) Pair with a Bluetooth Cell phone 4 2) Connect MV900 to your Cell Phone 4 5 10.
1. Introduction Thank you for purchasing the mVox MV900 Bluetooth speakerphone. The MV900 is a true hands-free speakerphone with built-in DSP voice processing technology, user independent voice dialing, and Bluetooth connectivity.
3. Charging To charge the MV900, use the included AC adapter or connect to a USB port on a computer. While the MV900 is charging, the charging indicator will show red. The indicator will turn green when the MV900 is fully charged. Note: A bus-powered USB hub cannot supply enough current for charging. We recommend plugging the MV900 directly into the computer’s USB port or using a self-powered USB hub.
9. Using as a Bluetooth Speakerphone with Cell Phones You will need to first pair the MV900 to your Cell phone before you can use the MV900 as a Bluetooth speakerphone. 1) Pair with a Bluetooth Cell phone Note: After MV900 is turned on, the MV900 will voice prompt “Connecting” then try to connect to the last Cell phone paired. If the previous paired Cell phone cannot be found or MV900 has not been paired before, the MV900 will voice prompt “Cell phone not available”.
10.
11. Using the Voice Command Recognition and Voice Keypad (VKP) To get into the voice command recognition mode, press and release the Talk Button, wait for the voice prompt “Please Say Command.” Proceed by saying one of the following commands.
Tips for using the Voice Recognition and Voice Keypad • Say the command after you have heard the beep • Say command or the numbers by speaking naturally. Avoid speaking too loud, too close to the microphone, or speaking too slow. • Always say “zero” for 0. Do not use “oh”. • You can press the Talk Button to cancel any commands to start things over. 1) Using Home, Work, Voicemail, Memory Press and release the Talk Button and say the command you would like to call.
2) Voice Keypad Dialing You can use the MV900 to dial the phone number. To use the Voice Keypad press and release the Talk Button wait for the voice prompt and say “Dial Number”, now say the phone number you would like to dial. 3) Cell Phone Name Dialing Follow your Cell Phone’s user manual to set up names or phone numbers on your Cell Phone. Press and release the Talk Button and say “Cell phone Name Dialing” and now say the name you want to call.
4) Speed Dial To use Speed Dial press and release the Talk Button say “Speed Dial X”, X being 1-9. Note: Speed Dial only works when you have setup Speed Dial on your Cell Phone. 5) Last Call You can redial the last phone number. Press and release the Talk Button on the MV900 and say “Last Call”, you will hear the voice prompt say “Last Call”.
6) Group Number Dialing Group number dialing will allow you to break up the telephone number into several groups to enter into the MV900. This is especially useful when using a calling card, or making long distance or international calls. After each group of numbers entered, the MV900 will voice prompt “Finish?” If the user replies “Yes”, the MV900 will dial the number that was confirmed. If the user replies “No”, the MV900 will beep, and then the user can say the next group of numbers.
7) Entering Touch Tone Numbers After your call is connected or during an active call, you may need to dial extension, first press and hold the Talk button and make sure that you hold the talk button until you hear the voice prompt “Say Extension Number”, release the talk button and say the extension numbers.
12. Setup Menu The MV900 provides memory slots to use the Voice Command Dialing.
Below are the steps to the ‘Caller ID’ setting. The same procedures are used for ‘Prompt’ and ‘Power-Save’. Press and release the Talk Button, say “Setup Menu”, then say “Caller ID”. MV900 will prompt the current mode (ON or OFF). If you say “Yes”, the MV900 will keep the current settings and the voice prompt will repeat “Set Up”. If you say “No”, the MV900 will toggle and prompt next option. When you have heard the one you want, say “Yes” to save.
13. Regulatory Information This product was tested and complies with the limits for a Class B digital device under Part 15 of the U.S. Federal Communications Commission (FCC) rules, and is subject to these conditions: It may not cause harmful interference and must accept any interference received, including any that causes undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
http://www.mvox.com For Tech Support 1-866-811-3830 ©2005, mVox Electronics, Inc.
