Specifications

ManualsBrandsMyalarm ManualsHome building and DecorD420

C-0636-020-01 0

D636A

Command

Features

Displays complete system

status in English text

Used with the

D4112

and

D6112

Control/

Communicators

Programmable custom text

for each zone

Easy to understand backlit

LCD Display

Illuminated

touchpad

Red Armed Status LED

Programmable “idle display”

text

Three programmable

one-

touch function keys

User friendly system status

sounder

Initiate local system test

and perimeter Watch from

the keypad

Multiple arming options and

special alarm options

Slim-line designer styling

compliments any decor.

Three expansion zones

Four-wire connection to

control/communicator

the

Center Specifications Sheet

75-05506-000-C 6/90

Command Control

The

D636A

Command Center does

more than just arm and disarm the

D4112/D6112 security system.

When you use the Command Bar

with one or two other keys, the D636

gives you control over the entire

security system.

The

D4112

and

D6112

Control/

Communicators can be program-

med for a wide variety of command

functions executed from the

D636A

Command Center.

Programmable Function

Keys

The

D636A

has three function keys,

and when used with the D6112, can

be programmed to perform most

system command functions (other

than arming commands) with the

touch of one key. When used with

the D4112, the function keys are

preprogrammed. Function key “A”

is Command 44 (local system test),

function key “B” is Command 47

(reset detectors), and function key

“C” is Command 5 (passcode

change).

English Language Display

The

D636A

display consists of 2

lines, each containing 16 characters

of English-language text. The first

line is the idle text display. This line

can be programmed to display your

company name when the Command

Center is in the idle state.

The second line displays all system

events, giving the end user instant

identification of system status. No

guesswork is involved. Program-

mable displays for each protective

zone give your company’s installa-

tions that special customized touch.

1989-1990 Radionics, Inc.

Summary of content (10 pages)

PAGE 1
C-0636-020-01 0 A R I D 0 N I C S D636A Command Center Specifications Sheet Features . Displays complete system status in English text Used with the D4112 and D6112 Control/ Communicators l . Programmable custom text for each zone . Easy to understand backlit LCD Display . Illuminated touchpad . Red Armed Status LED . Programmable “idle display” text l User friendly system status sounder . Initiate local system test and perimeter Watch from the keypad l l .
PAGE 2
C-0636-020-020 Zone Expansion The D636A provides the security system with three additional end-ofline resistor supervised hardwire protective zones (for use with the D6112 only). The protective zones report to the D6112 individually, and can be controlled from any Command Center assigned to the same account as the zone. User Programmable Passcodes Code Programmer. Basic programming for the security system is accomplished using the 6112:MAIN or D4 112:MAIN Product Handler.
PAGE 3
C-0636-030-01 0 R A D I 0 N I S C D636A Command Center Installation Instructions 1. General Description ENGLISH TEXT DISPLAY ARMED STATUS INDICATOR DIGITAL KEYPAD The D636A Command Center is a low profile surface mount, four-wire unit designedforuse with the Radionics D4112 and D6112 Control/Communicators.
PAGE 4
C-0636-030-020 4. Response Tones All command centers contain a sounder used to annunciate several system conditions and account conditions. The response tones for the D636A are as follows: Entrance Warning - The command center emits a pulsating beep during the entry delay period to remind the user to disarm the security system. This is a programmable function of the D4112 and D6112.
PAGE 5
PAGE 6
C-0636-030-040 D636A COMMAND CENTER BLACK I RED Figure 5: INSTALLING THE D636A COMMAND CENTER TO THE D6112 D636A COMMAND CENTER & / WHITE WHITE RED BLACK Figure 6: INSTALLING THE D636A COMMAND CENTER TO THE D4112 9.1 Remove the Front Cover - Remove the front cover from the enclosure base. Use a small flatbladed screwdriver to gently push the two bottom cover tabs back. As the tabs are pushed back, lift the bottom of the cover away from the base. Remove the cover. 9.
PAGE 7
C-0636-030-050 9.3 Mount the Enclosure Base- Place the enclosure base on the wall in the desired location. Use a centerpunchorapenciltomarkthelocationsofthe mounting holes. (The enclosure base can be mounted to a single-gang wall box if desired. Two mounting screw holes on the base are positioned for standard single-gang compatibility.) Secure the enclosure base to the wall or gang box. 9.4 Adjust the Display Contrast - Adjust the Potentiometer (see Figure 2) for optimum display contrast. 9.
PAGE 8
C-0636-030-060 10.4 Access the Handier as shown in Figure 8. a. Starting at OmegaWand 2.6, scan the ADVANCE bar code until 636 Keypad ##.## appears. Scan ENTER. b. 636M: New File appears, scan ENTER. C. When 636M : appears, enter a file name. ADVANCE 6 3 6 Other Handheld New Flh ADVANCE Other 636 Files 1 ENTER 4 Enter New File Name 636M: ADVANCE ENTER Zone 1 Display ADVANCE ENTER Enter the Custom Text for each zone , ADVANCE 7 ENTER Zone 2 Display ADVANCE ENTER l ADVANCE g.
PAGE 9
PAGE 10
C-0636-030-080 14. D636A Command Center Specifications Operating Voltage: Nominal 12 VDC supplied by the Control/ Communicator auxiliary power supply. Current Requirements: Jumper Intact: 34mA keypad on, LCD off, disarmed. Idle: 40mA keypad off, LCD off, LED on, armed. 75mA keypad on, LCD on, LED on, armed, alarm memory Maximum: 96mA keypad on, LCD on, LED on, tone on. Jumper Cut: Idle: 24mA keypad off, LCD off, disarmed. 30mA keypad off, LCD off, LED on, armed. Enclosure Dimensions: Height 4.