Datasheet
Technische Beschreibung mySmartControl 1.09 Seite: 3/12
www.myAVR.de © Laser & Co. Solutions GmbH - 12/2007 www.myAVR.com
Allgemeine Beschreibung
mySmartControl ist ein kompaktes Prozessorboard mit
einem AVR RISC Mikrocontroller von Atmel und standardi-
siertem USB-Interface. Die Programmierung erfolgt über
einen vorinstallierten Bootloader oder per ISP. Es ist mit
einem ATmega8 (8 KB FLASH und 3,6864 MHz) oder
einem ATmega168 (16 KB FLASH und 20 MHz) erhältlich.
Die Spannungsversorgung erfolgt per USB oder optional
onBoard. Es kann in 5 V oder in 3,3 V Zielumgebungen
eingebettet werden. Für die Steuerungsaufgaben verfügt
das Modul über eine 20polige Buchsenleiste nach dem
myAVR Standard. Es ist ein anschlussfertiges Modul. Die
Kommunikation mit dem PC läuft völlig transparent über
einen virtuellen COM-Port.
Das Board wird über die USB-Schnittstelle mit dem PC
verbunden und mit Spannung versorgt. Es ist kein Parallel-
oder COM-Port nötig, was vor allem für Notebookbesitzer
von Vorteil ist.
Die Versorgungsspannung kann wahlweise 3,3 V oder
5 V betragen (Datenblatt zum Controller beachten).
Das Board mySmartControl stellt eine kompakte Alternati-
ve zu dem Lern- und Experimentiersystem myAVR Board
2 USB dar.
General description
mySmartControl is a compact microcontroller-board with
an AVR RISC controller from Atmel and a standardized
USB interface. The programming is possible via a pre-
installed bootloader or over ISP. mySmartControl is avail-
able with an ATmega8 (8 KB FLASH and 3,6.864 MHz) or
an ATmega168 (16 KB FLASH and 20 MHz). The power
supply takes place over USB or a separate connection.
mySmartControl can be embedded in target-systems with
5 V or 3.3 V. In order to perform control tasks the module
uses a 20-pin female header as myAVR standard con-
nection. mySmartControl is ready to be used as it is. The
communication with the PC runs completely transparent
over a virtual COM-Port.
The board is connected with the PC over an USB inter-
face which is also responsible for the power supply. An
parallel port is not necessary, what is particularly an ad-
vantage for notebook owners.
For power supply you can choose between 3,3 V or 5 V
(attend the controller datasheet).
Our board mySmartControl is an alternative solution to
our educational board myAVR Board 2 USB.
Eigenschaften
• AVR-ATMEL-Prozessor-Board mit ATmega8 bzw.
Atmega168
• einfache Kommunikation des Mikrocontrollers mit
dem PC oder Notebook über die USB-Schnittstelle,
stellt einen virtuellen COM-Port im PC zur Verfügung
• Spannungsversorgung über USB-Anschluss 5 V oder
3,3 V
• schnelle Programmierung „in System“ wahlweise ü-
ber USB und Bootloader oder ISP
• Quarz für exaktes Timing
• Reset-Taster
• Power-LED
• 20 poliger Standard myAVR-Boardverbinder
• betriebsbereit bestückt
• optional bestückbare Spannungsversorgung für mehr
Leistung bzw. autonomen Betrieb
• optionaler ISP-Anschluß mit 10 PIN Atmel Standard-
belegung
• Industriestandard-Controller (CP2102) USB 2.0 zu
seriell Konverter
• vorbereitete spezielle Anschlüsse (Port D0, D1, B6,
B7, C6, C7)
• Leiterplatte gebohrt, verzinnt, Industriefertigung, ro-
bust, bedruckt
Properties
• AVR RISC controller board with ATmega8 or
ATmega168
• simple communication between microcontroller and
PC or notebook over the USB interface, which pro-
vides a virtual COM-Port to the PC
• power supply via USB connection, 5 V or 3.3 V
• fast "in system"-programming, alternatively over USB
and bootloader or ISP
• quarz for accurate timing
• reset button,
• power LED
• 20 pin female header as standard myAVR board
connector
• fully equipped
• optional equipped with external power supply connec-
tor (for more power resp. stand-alone use)
• optional equipped with standard Atmel ISP connector
• industrial standard-controller (CP2102) USB 2.0 to
serial bridge from SiLabs
• special connections prepared (Port D0, D1, B6, B7,
C6, C7)
• Printed circuit board pre-drilled, tin-plated, industrial
production, solid, printed
Stromstecker
external power supply
Spannungsversorgung
power supply unit
USB-Anschluss
USB Interface
ISP-Anschluss
ISP-interface
RESET
Power LED
Spannungskonfiguration
voltage selection
myAVR-Boardverbinder
myAVR Board connector