Information
myAVR
myAVR myAVR
myAVR
www.myAVR.de © Laser & Co. Solutions GmbH – 07/2007 www.myAVR.com
Produktbeschreibung
product description
mySmartControl
mySmartControl ist ein kompaktes Prozessorboard mit einem
AVR RISC Mikrocontroller von Atmel und standardisiertem
USB-Interface. Die Programmierung erfolgt über einen
vorinstallierten Bootloader oder per ISP. Es ist mit einem
ATmega8 (8 KB FLASH und 3,6864 MHz) oder einem
ATmega168 (16 KB FLASH und 20 MHz) erhältlich. Die
Spannungsversorgung erfolgt per USB oder optional mit
separatem Anschluss. Es kann in 5 V oder in 3,3 V Ziel-
umgebungen eingebettet werden. Für die Steuerungsaufgaben
verfügt das Modul über eine 20polige Buchsenleiste nach dem
myAVR Standard. Es ist ein anschlussfertiges Modul. Eine
Kommunikation mit dem PC kann völlig transparent über einen
virtuellen COM-Port geführt werden.
Das Board wird per USB-Schnittstelle mit dem PC verbunden
und mit Spannung versorgt. Es ist kein Parallel- oder COM-Port
nötig, was gerade für Notebookbesitzer von Vorteil ist.
Es sind zwei Versionen des mySmartControl verfügbar. Eine mit
dem ATmega8 und eine dem ATmega168 Mikrocontroller. Die
Versorgungsspannung kann wahlweise 3,3 V oder 5 V
betragen. Das mySmartControl Board stellt eine Alternative zu
dem Lern- und Experimentierboard myAVR Board 2 USB dar.
Es ist von den Abmessungen und der Auslegung vielseitig
anwendbar und sowohl für den Hobbyanwender als auch dem
professionellen Einsatz konzipiert. Es ist je nach Einsatz-
variante mit einer Vielzahl Bestückungsoptionen versehen.
mySmartControl is a compact microcontroller-board with a AVR
RISC controller from Atmel and a standardized USB interface.
The programming is possible via a pre-installed Boot loader or
over ISP. mySmartControl is available with an ATmega8 (8 KB
FLASH and 3,6.864 MHz) or an ATmega168 (16 KB FLASH
and 20 MHz). The power supply takes place over USB or a
separate connection. mySmartControl can be embedded in
target-systems with 5 V or 3.3 V. In order to perform control
tasks the module uses a 20-pin female header as myAVR
standard connection. mySmartControl is ready to be used as it
is. The communication with the PC runs completely transparent
over a virtual COM-Port.
The board is connexted with the PC over an USB interface
which is also responsible for the power supply. An parallel port
is not necessary, what is particularly an advantage for notebook
users. mySmartControl is available in two different versions –
either with the microcontroller ATmega8 or with the
microcontroller ATmega168. For power supply you can choose
between 3,3 V or 5 V.
Our board mySmartControl is an alternative solution to our
educational board myAVR Board 2 USB. It is small in size and
yet multifunctional. It can be used in small-sized systems as
well as in professional applications. mySmartUSB provides
many possibilities for use and different options for equipping.
Eigenschaften
• AVR RISC Prozessor-Board mit ATmega8 / ATmega168
• einfache Kommunikation des Mikrocontrollers mit dem PC
oder Notebook über die USB-Schnittstelle, stellt einen
virtuellen COM-Port im PC zur Verfügung
• Industriestandard-Controller (CP2102) USB 2.0 zu seriell
Konverter von SiLabs
• Spannungsversorgung über USB-Anschluss 5 V oder 3,3 V
• schnelle Programmierung „in System“ wahlweise über USB
und Bootloader oder ISP
• Quarz für exaktes Timing
• Reset-Taster, Power-LED
• 20 poliger Standard myAVR-Boardverbinder
• betriebsbereit bestückt
• optional bestückbare Spannungsversorgung für mehr Leistung
bzw. autonomen Betrieb
• optionaler ISP-Anschluß mit 10 PIN Atmel Standardbelegung
• vorbereitete spezielle PINs (Port D0, D1, B6, B7, C6, C7)
• Leiterplatte gebohrt, verzinnt, Industriefertigung, robust,
bedruckt
Properties
• AVR RISC controller board with ATmega8 or ATmega168
• simple communication between microcontroller and PC or
notebook over the USB interface, which provides a virtual
COM-Port to the PC
• industrial standard-controller (CP2102) USB 2.0 to serial
bridge from SiLabs
• power supply via USB connection, 5 V or 3.3 V
• fast "in system"-programming, alternatively over USB and
Bootloader or ISP
• quartz for accurate timing
• reset button, power LED
• 20-pin female header as standard myAVR board connector
• fully equipped
• optional equipped with external power supply connector (for
more power resp. stand-alone use)
• optional equipped with standard Atmel ISP connector
• special connections prepered (Port D0, D1, B6, B7, C6, C7)
• Printed circuit board pre-drilled, tin-plated, industrial
production, solid, printed