Wireless G Router User Manual ME1004-R Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
Table of Contents 1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Benefits of a Home Network . . . . . . . . . . . . . . . . . . . . . . . . . 1 Advantages of a Wireless Network . . . . . . . . . . . . . . . . . . . . 1 Placement of your Router for Optimal Performance . . . . . . . 2 2. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.
Downloaded from www.Manualslib.
Introduction 1 2 3 Benefits of a Home Network • Share one high-speed Internet connection with all the computers in your home 4 • Share resources, such as files, and hard drives among all the connected computers in your home 5 • Share a single printer with the entire family 6 • Share documents, music, video, and digital pictures • Store, retrieve, and copy files from one computer to another • Simultaneously play games online, check Internet email, and chat 7 8 Advantages of a Wireless Network • Mobi
Introduction Placement of your Router for Optimal Performance Important Factors for Placement and Setup Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases. This may or may not be noticeable to you.
Introduction Avoid placing your Router near devices that may emit radio “noise,” such as microwave ovens. Dense objects that can inhibit wireless communication include: • Refrigerators 1 2 3 • Washers and/or dryers • Metal cabinets • Large aquariums • Metallic-based, UV-tinted windows If your wireless signal seems weak in some spots, make sure that objects such as these are not blocking the signal’s path (between your computers and Router). 3.
Introduction 4. Choose the “Quietest” Channel for your Wireless Network In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours.
Introduction If you continue to have difficulty with secure connections, VPNs, and AOL, please review the steps above to be sure you have addressed these issues. For more information regarding our networking products, visit our website at www.MyEssentialssupport.com or call MyEssentials Technical Support at: 1 2 3 4 5 US: 1-866-761-4608 6 7 8 9 10 5 Downloaded from www.Manualslib.
Product Overview Product Features In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Wireless G Router from MyEssentials an ideal solution for your home or small office network. Works with Both PCs and Mac ® Computers The Router supports a variety of networking environments including Mac OS ®, 9.x, X v10.x, AppleTalk ®, Linux ®, Windows ® 98, Me, NT ®, 2000, and XP, and others.
Product Overview SPI Firewall Integrated 10/100 4-Port Switch The Router has a built-in, 4-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more. The switch features automatic detection so it will adjust to the speed of connected devices. The switch will transfer data between computers and the Internet simultaneously without interrupting or consuming resources.
Product Overview Quick Installation Software The Quick Installation Software takes the guesswork out of setting up your Router. This automatic software determines your network settings for you and sets up the Router for connection to your Internet Service Provider (ISP). In a matter of minutes, your Wireless Router will be up and running on the Internet. NOTE: Quick Installation Software is compatible with Windows 98SE, Me, 2000, XP, and Mac OS X.
Knowing your Router Package Contents 1 • Wireless G Router • Quick Installation Guide • MyEssentials Quick Installation Software CD with User Manual • Power Supply 4 System Requirements • Broadband Internet connection such as a DSL or cable modem with RJ45 (Ethernet) connection • At least one computer with an installed network interface adapter • TCP/IP networking protocol installed on each computer • RJ45 Ethernet networking cable • Internet browser 5 6 7 Quick Installation Software System Requiremen
Knowing your Router The Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The LED indicators are easily visible on the front of the Router to provide you with information about network activity and status. (1) (2) (5) ����� �������� �������� ��������������� ����� (4) (3) 1. When you apply power to the Router or restart it, a short period of time elapses while the Router boots up.
Knowing your Router 3. OFF No Device is Linked to the Port Green 10/100Base-T Device Connected Blinking (Orange or Green) Port Activity 2 3 4 5 6 4. This LED lights in GREEN to indicate that your modem is connected properly to the Router. It blinks rapidly when information is being sent over the port between the Router and the modem. OFF No WAN Link Solid Green Good WAN Link Blinking Green WAN Activity 5. This unique LED shows you when the Router is connected to the Internet.
Knowing your Router (8) (7) (9) (6) ����� ����� � � � ��������������� � ������ ������������ 6. Power Jack Connect the included 5V DC power supply to this jack. 7. Wired Computers Connect your wired (non-wireless) computers to these ports. These ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable. The ports are labeled 1 through 4. These ports correspond to the numbered LEDs on the front of the Router. 8.
Knowing your Router 9. Reset 1 2 3 4 a. Resetting the Router Push and release the “Reset” button. The lights on the Router will momentarily flash. The Power/Ready light will begin to blink. When the Power/Ready light becomes solid again, the reset is complete. b. Restoring the Factory Defaults Press and hold the “Reset” button for at least 10 seconds, then release it. The lights on the Router will momentarily flash. The “Power/Ready” light will begin to blink.
Connecting and Configuring your Router Verify the contents of your box. You should have the following: • Wireless G Router • Quick Installation Guide • MyEssentials Quick Installation Software CD with User Manual • RJ45 Ethernet Networking Cable (for connection of the Router to the computer) • Power Supply Modem Requirements Your DSL or cable modem must be equipped with an RJ45 Ethernet port. Many modems have both an RJ45 Ethernet port and a USB connection.
Connecting and Configuring your Router Step 1 Run the Quick Installation Software 1 Shut down any programs that are running on your computer at this time. 2 1.2 Make sure you have the following items at the computer that is now directly connected to the DSL or cable modem. DO NOT CONNECT THE ROUTER AT THIS TIME. 3 • Quick Installation Guide • The Quick Installation Software CD with User Manual • The Router • The Router’s Power Supply • RJ45 Ethernet Networking Cable 1.
Connecting and Configuring your Router Welcome Screen After you insert the CD into your CD-ROM drive, the Wizard’s welcome screen will appear. Make sure you have not connected the Router at this point. If you have connected your Router, please reconnect your computer directly to the modem. Click “Run the Quick Installation Software” when you are ready to move on. Progress Screen The Quick Installation Software will show you a progress screen each time a step in the setup has been completed.
Connecting and Configuring your Router Step 2 1 Set up the Hardware The Wizard will walk you through connecting your Router to your computer and modem. Follow the steps on the screen using the pictures as a guide. This step instructs you to locate the cable connected between your modem and the networking port on your computer. Unplug this cable from the computer and plug it into the GREEN port on the Router. Click “Next” to continue. 3 4 5 6 7 2.2 17 Downloaded from www.Manualslib.
Connecting and Configuring your Router 2.3 This step instructs you to locate the power supply that is included with your Router. Plug the power supply’s small connector into the power port on the Router. Plug the power supply into an empty power outlet. Click “Next” to continue. 2.4 This step instructs you to look at the lights on the front of your Router. Make sure the appropriate lights are ON. Refer to the Quick Installation Software on your computer’s screen for more details.
Connecting and Configuring your Router Step 3 1 Check the Connection 3.1 3.3 19 Downloaded from www.Manualslib.com manuals search engine User Name and Password Needed If you have a connection type that requires a user name and a password, the Wizard will ask you to type in your user name and password. If your connection type does not require a user name and password, you will not see this screen. Your user name and password is provided to you by your Internet Service Provider.
Connecting and Configuring your Router Step 4 Secure your Network 4.1 After connection has been established, you will be prompted by the Quick Installation Software to select your desired security level. 4.2 WEP and WPA are the two security options. If you do not want security or would prefer to install at a later time, click the radio button next to “NONE” and click “Next.” 4.3 The Wi-Fi Protected Access (WPA) security option features a two-password setup.
Connecting and Configuring your Router Step 5 1 Configure the Router 2 3 4 5 5.1 5.2 Checking Internet The Wizard will now check for an Internet connection. This can take a few minutes. The Wizard may not detect a connection right away. If not, it will retry a number of times. The “Connected” light on the front panel of the Router will flash during this time. Please be patient through this process. Finished When the Internet connection is complete, the Wizard will tell you that you are finished.
Alternate Setup Method The Web-Based Advanced User Interface is a web-based tool that you can use to set up the Router if you don’t want to use the Quick Installation Software. You can also use it to manage advanced functions of the Router.
Alternate Setup Method Step 1 1 Connect your Router 1.1 Turn off the power to your modem by unplugging the power supply from the modem. 1.2 Locate the network cable that is connected between your modem and your computer and unplug it from your computer, leaving the other end connected to your modem. 1.3 Plug the loose end of the cable you just unplugged into the port 1.4 Connect a new network cable (not included) from the back of the computer to one of the wired computer ports labeled “1–4”.
Alternate Setup Method Step 3 Configure the Router Using the Web-Based Advanced User Interface Using your Internet browser, you can access the Router’s Web-Based Advanced User Interface. In your browser, type “192.168.2.1” (you do not need to type in anything else such as “http://” or “www”). Then press the “Enter” key. PLEASE NOTE: If you have difficulty accessing the Router’s Web-Based Advanced User Interface, go to the section entitled “Manually Configuring Network Settings”.
Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface The home page is the first page you will see when you access the Web-Based Advanced User Interface (UI). The home page shows you a quick view of the Router’s status and settings. All advanced setup pages can be reached from this page. 1 2 3 4 5 7 1. Quick-Navigation Links You can go directly to any of the Router’s UI pages by clicking directly on these links.
Using the Web-Based Advanced User Interface 3. Internet Status Indicator This indicator is visible in all pages of the UI, indicating the connection status of the Router. When the indicator says “connection OK” in GREEN, the Router is connected to the Internet. When the Router is not connected to the Internet, the indicator will read “no connection” in RED. The indicator is automatically updated when you make changes to the settings of the Router. 4.
Using the Web-Based Advanced User Interface Step 4 Configure your Router for Connection to your Internet Service Provider (ISP) 2 3 4 5 6 7 8 9 (A) (B) (C) (1) 10 (2) Setting your Connection Type From the “Connection Type” page, you can select the type of connection you use. Select the type of connection you use by clicking the button (1) next to your connection type and then clicking “Next” (2). 27 Downloaded from www.Manualslib.
Using the Web-Based Advanced User Interface Setting your Internet Service Provider (ISP) Connection Type to Dynamic IP A dynamic connection type is the most common connection type used with cable modems. Setting the connection type to “dynamic” in many cases is enough to complete the connection to your ISP. Some dynamic connection types may require a host name. You can enter your host name in the space provided if you were assigned one. Your host name is assigned by your ISP.
Using the Web-Based Advanced User Interface Setting your Internet Service Provider (ISP) Connection Type to Static IP A static IP address connection type is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This information is available from your ISP or on the paperwork that your ISP left with you. Type in your information, then click “Apply Changes” (5).
Using the Web-Based Advanced User Interface Setting your ISP Connection Type to PPPoE Most DSL providers use PPPoE as the connection type. If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service. If you have an Internet connection in your home or small office that doesn’t require a modem, you may also use PPPoE.
Using the Web-Based Advanced User Interface 3. Service Name A service name is rarely required by an ISP. If you are not sure if your ISP requires a service name, leave this blank. 4. MTU 1 2 The MTU setting should never be changed unless your ISP gives you a specific MTU setting. Making changes to the MTU setting can cause problems with your Internet connection including disconnection from the Internet, slow Internet access, and problems with Internet applications working properly. 3 5.
Using the Web-Based Advanced User Interface Setting Custom Domain Name Server (DNS) Settings A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locators (URLs) like “www.MyEssentialssupport.com” into IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router. The “Automatic from ISP” box (1) should be checked if your ISP did not give you a specific DNS address.
Using the Web-Based Advanced User Interface Configuring your WAN Media Access Controller (MAC) Address All network components including cards, adapters, and routers, have a unique “serial number” called a MAC address. Your Internet Service Provider may record the MAC address of your computer’s adapter and only let that particular computer connect to the Internet service. When you install the Router, its own MAC address will be “seen” by the ISP and may cause the connection not to work.
Using the Web-Based Advanced User Interface Cloning your MAC Address To clone your MAC address, make sure that you are using the computer that was ORIGINALLY CONNECTED to your modem before the Router was installed. Click the “Clone” button (1). Click “Apply Changes” (3). Your MAC address is now cloned to the Router. Entering a Specific MAC Address In certain circumstances you may need a specific WAN MAC address. You can manually enter one in the “MAC Address” page.
Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Using your Internet browser, you can access the Router’s Web-Based Advanced User Interface. In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”), then press the “Enter” key. You will see the Router’s home page in your browser window. 1 2 3 4 (1) 5 6 7 8 (2) (3) 9 10 35 Downloaded from www.Manualslib.
Using the Web-Based Advanced User Interface Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed and changed here. (1) (2) (3) (4) (5) (6) 1. IP Address The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the Web-Based Advanced User Interface, type this IP address into the address bar of your browser. This address can be changed if needed.
Using the Web-Based Advanced User Interface 3. DHCP Server The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is “On”. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network. To turn off the DHCP server, select “Off” and click “Apply Changes”. 1 2 3 4.
Using the Web-Based Advanced User Interface Viewing the DHCP Client List Page You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computer’s network interface card (NIC). Pressing the “Refresh” (4) button will update the list. If there have been any changes, the list will be updated.
Using the Web-Based Advanced User Interface Configuring the Wireless Network Settings Clicking on the header of the “Wireless” tab will take you to the “Wireless” header page. Under the “Wireless” tab, there are links that allow you to make changes to the wireless network settings. 1 2 3 4 5 7 8 9 10 39 Downloaded from www.Manualslib.
Using the Web-Based Advanced User Interface Changing the Wireless Network Name (SSID) To identify your wireless network, a name called the SSID (Service Set Identifier) is used. The default SSID of the Router is “MyEssentials”. You can change this to anything you want to or you can leave it unchanged. If there are other wireless networks operating in your area, you will want to make sure that your SSID is unique (does not match that of another wireless network in the area).
Using the Web-Based Advanced User Interface Using the Wireless Mode Switch Your Router can operate in three different wireless modes: “g and b”, “g only”, and “b only”. The different modes are explained below. 1 2 3 4 5 7 g and b Mode In this mode, the Router is compatible with 802.11b and 802.11g wireless clients simultaneously. This is the factory default mode and ensures successful operation with all Wi-Fi-compatible devices. If you have a mix of 802.11b and 802.
Using the Web-Based Advanced User Interface QoS (Quality of Service) Configuration QoS prioritizes important data on your network such as multimedia content and Voice over IP (VoIP) so it will not be interfered with by other data being sent over the network. Based on 802.11e, you can turn this feature on or off by selecting it from the drop-down menu and choosing the acknowledgement mode you want to use.
Using the Web-Based Advanced User Interface Using the Broadcast SSID Feature Note: This advanced feature should be employed by advanced users only. For security, you can choose not to broadcast your network’s SSID. Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks. To turn off the broadcast of the SSID, remove the check mark from the box next to “Broadcast SSID”, and then click “Apply Changes”. The change is immediate.
Using the Web-Based Advanced User Interface Securing your Wi-Fi ® Network Here are a few different ways you can maximize the security of your wireless network and protect your data from prying eyes and ears. This section is intended for the home, home office, and small office user. At the time of this User Manual’s publication, there are four encryption methods available.
Using the Web-Based Advanced User Interface 128-Bit WEP As a result of 64-bit WEP’s potential security weaknesses, a more secure method of 128-bit encryption was developed. 128-bit encryption includes a key length of 104 bits plus 24 additional bits of system-generated data (128 bits total). Some hardware manufacturers refer to 128-bit as 104-bit encryption.
Using the Web-Based Advanced User Interface Wi-Fi Protected Access (WPA) WPA is a new Wi-Fi standard that was designed to improve upon the security features of WEP. To use WPA security, the drivers and software of your wireless equipment must be upgraded to support WPA. These updates will be found on the wireless vendor’s website. There are three types of WPA security: WPA-PSK (no server), WPA (with radius server), and WPA2. WPA-PSK (no server) uses what is known as a pre-shared key as the network key.
Using the Web-Based Advanced User Interface Sharing the Same Network Keys Most Wi-Fi products ship with security turned off. So once you have your network working, you need to activate WEP or WPA and make sure your wireless networking devices are sharing the same network key. 1 2 3 4 5 7 8 9 10 47 Downloaded from www.Manualslib.
Using the Web-Based Advanced User Interface Using a Hexadecimal Key A hexadecimal key is a combination of numbers and letters from A–F and 0–9. 64-bit keys are five two-digit numbers. 128-bit keys are 13 two-digit numbers. For instance: AF 0F 4B C3 D4 = 64-bit key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key In the boxes below, make up your key by writing in two characters between A–F and 0–9 in each box.
Using the Web-Based Advanced User Interface WEP Setup 64-Bit WEP Encryption 1 1. Select “64-bit WEP” from the “Security” menu’s “Security Mode”. 2. After selecting your WEP encryption mode, you can enter your key by typing in the hex key manually, or you can put a check mark in “Passphrase”, then type in your passphrase. Click “Generate” to generate four different hex keys. A hex (hexadecimal) key is a combination of numbers and letters from A–F and 0–9. For 64-bit WEP, you need to enter 10 hex keys.
Using the Web-Based Advanced User Interface 128-Bit WEP Encryption Note to Mac users: The passphrase option will not operate with Apple AirPort. To configure encryption for your Mac computer, set the encryption using the manual method described in the next section. 1. Select “128-bit WEP” from the “Security” menu’s “Security Mode”. 2. After selecting your WEP encryption mode, you can enter your key by typing in the hex key manually, or you can put a check mark in “Passphrase”, then type in your passphrase.
Using the Web-Based Advanced User Interface Changing the Wireless Security Settings Your Router is equipped with WPA (Wi-Fi Protected Access), the latest wireless security standard. It also supports the legacy security standard, WEP (Wired Equivalent Privacy). By default, wireless security is disabled. To enable security, you must first determine which standard you want to use. To access the security settings, click “Security” on the “Wireless” tab. WPA uses a so-called pre-shared key as the security key.
Using the Web-Based Advanced User Interface Guest Access (Optional) The guest pre-shared key allows guest users an Internet-only access to restrict them from entering your network and having access to files on your PCs. Enter your pre-shared key for guest access. This can be from eight to 63 characters and can be letters, numbers, or symbols. Click “Apply Changes” to finish.
Using the Web-Based Advanced User Interface Setting up Windows XP Wireless Network Utility to use WPA-PSK In order to use WPA-PSK, ensure you are using the Windows Wireless Network Utility by doing the following: 1. Under Windows XP, click “Start > Control Panel > Network Connections”. 2. Right-click on “Wireless Network Connection Properties” and select “Properties”. 3. Clicking on the “Wireless Networks” tab will display the following screen.
Using the Web-Based Advanced User Interface 4. Under the “Wireless Networks” tab, click the “Configure” button and you will see the following screen. 5. For a home or small business user, select “WPA-PSK” under “Network Authentication”. Note: Select “WPA” if you are using this computer to connect to a corporate network that supports an authentication server such as a radius server. Please consult your network administrator for further information. 6. Select “TKIP” or “AES” under “Data Encryption”.
Using the Web-Based Advanced User Interface Using the Access Point Mode Note: This advanced feature should be employed by advanced users only. The Router can be configured to work as a wireless network access point. Using this mode will defeat the NAT IP sharing feature and DHCP server. In Access Point (AP) mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network that you will bridge to. The default IP address is 192.168.2.
Using the Web-Based Advanced User Interface Configuring the Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including: • IP Spoofing • SYN flood • Land Attack • UDP flooding • Ping of Death (PoD) • Tear Drop Attack • Denial of Service (DoS) • ICMP defect • IP with zero length • RIP defect • Smurf Attack • Fragment flooding • TCP Null Scan The firewall also masks common ports that are frequently used to attack networks.
Using the Web-Based Advanced User Interface Configuring Internal Forwarding Settings The “Virtual Servers” function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network. Since your internal computers are protected by a firewall, computers outside your network (over the Internet) cannot get to them because they cannot be “seen.
Using the Web-Based Advanced User Interface Setting Client IP Filters The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers. To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP fields (1). Next, enter “80” in both the port fields (2). Select “Both” (3).
Using the Web-Based Advanced User Interface Setting MAC Address Filtering The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client (computer) on your network to allow network access to each.
Using the Web-Based Advanced User Interface Enabling the Demilitarized Zone (DMZ) The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is NOT protected from hacker attacks.
Using the Web-Based Advanced User Interface WAN Ping Blocking Computer hackers use what is known as “pinging” to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. The Router can be set up so it will not respond to an ICMP ping from the outside. This heightens the level of security of your Router.
Using the Web-Based Advanced User Interface Utilities Tab This screen lets you manage different parameters of the Router and perform certain administrative functions. 62 Downloaded from www.Manualslib.
Using the Web-Based Advanced User Interface Restarting the Router Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings. Restarting the Router to Restore Normal Operation 1. Click the “Restart Router” button. 3. The following message will appear. Restarting the Router can take up to 25 seconds. It is important not to turn off the power to the Router during the restart. 4.
Using the Web-Based Advanced User Interface Restoring Factory Default Settings Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults. 1. Click the “Restore Defaults” button. 2. The following message will appear. Click “OK”. 3. The following message will appear. Restoring the defaults includes restarting the Router. It can take up to 25 seconds.
Using the Web-Based Advanced User Interface Saving a Current Configuration You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. 1. Click “Save”. A window called “File Download” will open. Click “Save”. 1 2 3 4 5 2.
Using the Web-Based Advanced User Interface Restoring a Previous Configuration This option will allow you to restore a previously saved configuration. 1. Click “Browse”. A window will open that allows you to select the location of the configuration file. All configuration files end with a “.bin”. Locate the configuration file you want to restore and double-click on it. 2. You will be asked if you want to continue. Click “OK”. 3. A reminder window will appear.
Using the Web-Based Advanced User Interface Updating the Firmware From time to time, MyEssentials may release new versions of the Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may exist. When MyEssentials releases new firmware, you can download the firmware from the MyEssentials update website and update your Router’s firmware to the latest version.
Using the Web-Based Advanced User Interface Changing the Login Time-Out Setting The login time-out option allows you to set the period of time that you can be logged into the Router’s Web-Based Advanced User Interface. The timer starts when there has been no activity. For example, you have made some changes in the Web-Based Advanced User Interface, then left your computer alone without clicking “Logout”.
Using the Web-Based Advanced User Interface 1 2 3 4 5 6 7 8 9 10 Enabling/Disabling Network Address Translation (NAT) Note: This advanced feature should be modified by advanced users only. NAT is the method by which the Router shares the single IP address assigned by your ISP with the other computers on your network and is enabled by default. NAT should only be disabled if your ISP assigns you multiple IP addresses or you need NAT disabled for an advanced system configuration.
Using the Web-Based Advanced User Interface Enabling/Disabling UPnP UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your MyEssentials Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Some applications require the Router’s firewall to be configured in a specific way to operate properly. This usually requires opening TCP and UDP ports.
Manually Configuring Network Settings In order for your computer to properly communicate with your Router, you will need to change your PC’s TCP/IP settings to DHCP. Manually Configuring Network Adapters in Windows 2000, NT, or XP 1. Click “Start”, “Settings”, then “Control Panel”. 2. Double-click on the “Network and dial-up connections” icon (Windows 2000) or the “Network” icon (Windows XP). 3.
Manually Configuring Network Settings Manually Configuring Network Adapters in Windows 98SE or Me 1. Right-click on “My Network Neighborhood” and select “Properties” from the drop-down menu. 2. Select “TCP/IP -> settings” for your installed network adapter. You will see the following window. (1) (3) (2) 3. If “Specify an IP address” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below.
Manually Configuring Network Settings 4. Write in the IP address and subnet mask from the “IP Address” tab (3). 5. Click the “Gateway” tab (2). Write the gateway address down in the chart. 6. Click the “DNS Configuration” tab (1). Write the DNS address(es) in the chart. 7. If not already selected, select “Obtain IP address automatically” in the “IP Address” tab. Click “OK”. Restart the computer. When the computer restarts, your network adapter(s) are now configured for use with the Router.
Manually Configuring Network Settings Manually Configuring Network Adapters in Mac OS X 1. Click on the “System Preferences” icon. 2. Select “Network” (1) from the “System Preferences” menu. (1) 3. Select “Built-in Ethernet” (2) next to “Show” in the Network menu. (2) (5) (3) (4) 74 Downloaded from www.Manualslib.
Recommended Web Browser Settings 4. 5. Select the “TCP/IP” tab (3). Next to “Configure:” (4), you should see “Manually” or “Using DHCP”. If you do not, check the PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT selected. If it is, you will need to configure your Router for a PPPoE connection type using your user name and password. If “Manually” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below.
Recommended Web Browser Settings In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browser’s settings to the recommended settings in this section. Internet Explorer 4.0 or Higher 1. Start your web browser. Select “Tools” then “Internet Options”. 2.
Recommended Web Browser Settings 4. Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page. 1 2 3 4 5 6 7 Netscape Navigator 4.0 or Higher ® 1. Start Netscape. Click on “Edit” then “Preferences”. 2. In the “Preferences” window, click on “Advanced” then select “Proxies”.
Troubleshooting Problem: Installation CD does not automatically start. Solution: If the CD-ROM does not start the Quick Installation Software automatically, it could be that the computer is running other applications that are interfering with the CD drive. 1. If the Quick Installation Software screen does not appear within 15–20 seconds, open up your CD-ROM drive by double-clicking on the “My Computer” icon that is located on your desktop. 2.
Troubleshooting Problem: The Quick Installation Software cannot find my Router. Solution: If the Quick Installation Software is not able to find the Router during the installation process, please check the following items: 1. If the Quick Installation Software is not able to find the Router 2. Unplug power to the Router for 10 seconds, and then plug the power back into the Router. Ensure that the Router’s Power light is on; it should be solid green.
Troubleshooting Problem: The Quick Installation Software cannot connect my Router to the Internet. Solution: If the Quick Installation Software is not able to connect the Router to the Internet, please check the following items: 1. Use the troubleshooting suggestions within the Quick Installation Software. If the troubleshooting screen does not open automatically, click on the “Troubleshoot” button in the lower, right-hand corner of the Quick Installation Software window. 2.
Troubleshooting Problem: • The Quick Installation Software completed installation, but my web browser doesn’t work. • I am unable to connect to the Internet. The Router’s “WAN” light is off and the “Connected” light is blinking. Solution: If you cannot connect to the Internet, the “WAN” light is off, and the “Connected” light is blinking, the problem may be that your modem and Router are not connected properly. 1. Make sure the network cable between the modem and the Router is connected.
Troubleshooting Problem: • The Quick Installation Software completed installation, but my web browser doesn’t work. • I am unable to connect to the Internet. The Router’s “WAN” light is on and the “Connected” light is blinking. Solution: If you cannot connect to the Internet, the “WAN” light is on, and the “Connected” light is blinking, the problem may be that your connection type may not match the ISP’s connection.
Troubleshooting Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access. If you are still unable to access the Internet after disabling any firewall software, please contact MyEssentials Technical Support at 866-761-4608. Problem: I can’t connect to the Internet wirelessly. 1 2 3 4 Solution: If you are unable to connect to the Internet from a wireless computer, please do the following: 1.
Troubleshooting Problem: I can’t connect to the Internet wirelessly, but my network name is listed. Solution: If the name of your network is listed in the “Available Networks” list, please follow the steps below to connect wirelessly: 1. Click on the correct network name in the “Available Networks” list. 2. If the network has security (encryption) enabled, you will need to enter the network key.
Troubleshooting Problem: My wireless network performance is inconsistent. Data transfer is sometimes slow. 1 2 Signal strength is poor. I am having difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection. 3 Solution: 4 Wireless technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases.
Troubleshooting Problem: I am having difficulty setting up Wired Equivalent Privacy (WEP) security on the Router. Solution: 1. Log into your Wireless Router. Open your web browser and type in the IP address of the Wireless Router (the Router’s default is 192.168.2.1). Log into your Router by clicking on the “Login” button in the top, right-hand corner of the screen. You will be asked to enter your password. If you never set a password, leave the password field blank and click “Submit”.
Troubleshooting Problem: I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a client card from MyEssentials (Wireless Network Card or Adapter). Solution: The client card must use the same key as the Wireless G Router or access point. For instance, if your Wireless Router or access point uses the key 00112233445566778899AABBCC, then the client card must be set to the exact same key. 1. Double-click the “Signal Indicator” icon to bring up the “Wireless Networking Utility” screen.
Troubleshooting Problem: Do MyEssentials products support WPA? Solution: Note: To use WPA security, all your clients must be upgraded to drivers and software that support it. At the time of this publication, a security patch download is available, for free, from Microsoft. This patch works only with the Windows XP operating system. Download the patch here: http://www.microsoft.com/downloads/details.
Troubleshooting Problem: I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a client card from MyEssentials (Wireless Network Card or Adapter) for a home network. Solution: Clients must use the same key that the Wireless G Router or access point uses. For instance, if the key is “Smith Family Network Key” in the Wireless G Router or access point, the clients must also use that same key. 1.
Troubleshooting Problem: I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a client card from MyEssentials (Wireless Network Card or Adapter) for a business. Solution: 1. Double-click the “Signal Indicator” icon to bring up the “Wireless Networking Utility” screen. The “Advanced” button will allow you to view and configure more options of your client card. 2. Once the “Advanced” button is clicked, the WNU will appear.
Troubleshooting Enabling WPA-PSK (no server) 1. In systems running Windows XP, click “Start > Control Panel > Network Connections”. 2. Right-click on the “Wireless Networks” tab. The “Wireless Network Connection Properties” screen appears. Ensure the “Use Windows to configure my wireless network settings” box is checked. 3. Under the “Wireless Networks” tab, click the “Configure” button, and you will see the client card properties screen. 4.
Information FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, MyEssentials, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product, ME1004-R to which this declaration relates, complies with Part 15 of the FCC Rules.
Information Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by MyEssentials may void the user’s authority to operate the equipment. MyEssentials 1-Year Limited Product Warranty MyEssentials warrants this product against defects in materials and workmanship for one year.
Wireless G Router www.MyEssentialssupport.com MyEssentials Tech Support: US: 1-866-761-4608 © 2006 Belkin Corporation. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Mac OS and AppleTalk are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. Windows, NT, and Microsoft are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. P75284 Downloaded from www.Manualslib.
