Instruction Manual

1
OPERATING INSTRUCTIONS
The following are basic instructions for operating the PTBT2 ULTRAPEN &App. To
accessafullOperationsManual:
1. InsidetheApptapthePreferencesbuttonontheFeature
NavigationBar.
2. SelectHelpfromtheSettingsMenuscreen.
3. ThebrowserofyourmobiledeviceswillopenandlinktotheMyronL
®
Company
websitepagewherethePTBTxOperationsManualcanbeaccessed.
I. Connecting the ULTRAPEN to the Mobile Device
TopairandconnectthePTBT2toyourmobiledevice:
1. InsidetheApptaptheConnectbuttonintheFeatureNavigationBar.
2. PushandreleasethebuttononthePTBT2toturnitON.
3. WhenthePTBT2’snameappearsontheConnectScreen,selectthatline.
4. AcheckmarkwillappearnexttoPTBT2’sname.
NOTE:The default namefor all PTBT2’s is, “MLC-PTBTx”. To edit the name, Tap the
Preferences button and go to ULTRAPEN Settings section. See the PTBTx
OperationsManualforfullinstructiions.
TounpairfromaPTBT2:
1. TaptheredUnpairbuttonnexttothePTBT2’sname.
2. AnUnpairInstrumentdialogueboxwillappear.
3. TaptheDisconnectbuttoninthedialoguebox.
II. Temperature Unit Selection
ThePTBT2allowsyoutoselecteitherCentigrade(°C)orFarenheit(°F)whendisplaying
temperatureontheiOSscreens.
ToselecttheTemperatureUnits:
1. InsidetheApptapthe PreferencesbuttonontheFeatureNavigationBar.
2. SelectApplication Preferencesfromthelistofsettingstopics.
3. SlidetheTemperatureUnitsswitchleftorrighttodisplay
temperaturevaluesaseither°Cor°F.
III. pH Mode Selection
ThePT2allowsyoutoselectbetweentwopHmeasurementmodes:
Hold(Default):Oncestabilized,thereadingiscapturedthendisplayed.
LIVE:Real-timereadingsaredisplayedcontinuouslyduringmeasurementuntilthe
ULTRAPENtimesout.
ToselectthepHMode:
1. InsidetheApptap the PreferencesbuttonontheFeature
NavigationBar.
2. SelectULTRAPEN Settingsfromthelistofsettingstopics
3. PushandreleasethebuttononthePTBT2toturnitON.
4 When the PTBT2 LED begins to ash, TheApp will display, “Press and hold the
button on the ULTRAPEN to enter Preferences”
5. PressandholdthePTBT2’spushbutton.
6. WhentheLEDgoestosolidONtheULTRAPENSettingsscreenwillappear.
7. SelectPen ModefromtheULTRAPENSettingsscreen.ThePenModescreenwill
appear.
8. TapthePen Modefieldonthescreen.
9. Choosethedesiredmode(HoldorLive)fromthelistthatappears.
10. Tapthe Applybutton.
IV. pH Measurement
ThefollowingtableexplainstheLEDIndicatorsignalsandtypicaldurations.
LED Indicator Signal Meaning Duration
RapidFlashing Dippeninsolution 6sec
SlowFlashing SwirlPen.Measurementinprocess
InLIVEmode,thereadingsare
dispayed.
10-30secinHoldmode
5minutesinLivemode
SolidONLight Measurementiscomplete
Finalreadingisdisplayed.
≤6sec
To measure solution at the extremes of the specified temperature range,
allowthepen toequilibratebysubmerging thecell inthesamplesolution ofthesame
temperaturefor1minutepriortotakingameasurement.
NOTE:Ifyoucannotdipthepeninthesamplesolution,pourthesampleintoaclean
container.Ifyoudon’thaveasamplecontainerorneedtotestaverticalstreamof
solution,usethescoop.
2
CAUTION: