Use and Care Manual

GEM Series Wall Models
Installation and Operating Instructions
4 mounting supports
1 Allen wrench (6mm)
4 wall mounts
4 screws
4 wall plugs
1 Allen wrench (3mm)
6.0mm
The maximum temperature on an exposed surface is 135º F.
In accordance with our policy of continual product improvement, we reserve the right to amend
specifications without prior notification.
ELECTRICAL SPECIFICATIONS
The Towel Warmer requires 120VAC, 60Hz power supply.
The Towel Warmer is to be protected by a separate 15 amp circuit breaker or equal.
BOX CONTENTS
• Towel Warmer • Installation & Operating Instructions
• Fixing Kit • Warranty Information Sheet
Unpack the Towel Warmer carefully to avoid any damage or loss of any part. When opening the box, care
should be taken not to discard packet of mounting screws. It is your responsibility to immediately inspect
for any damage. Shipping damage should be reported immediately to your place of purchase.
Follow instructions to make certain your Towel Warmer is properly attached to the wall.
FAILURE TO FOLLOW THESE STEPS COULD RESULT IN HAZARDOUS CONDITIONS.
To avoid possible fire hazard, the Towel Warmer must be mounted as intended. MOUNT THIS
UNIT ONLY AS SHOWN IN THESE INSTRUCTIONS. Mounting the Towel Warmer in a manner
other than shown on the front page may cause it to overheat.
The Towel Warmer must be used in accordance with any prevailing code and relevant electrical wiring rules
and regulations, in particular regulations that cover the use of products and accessories in damp situations
such as bathrooms, showers, laundries and other areas with fixed water containers.
• Towel Warmer must be mounted on a vertical wall with the cord in position as shown on the front page.
No other position is safe or acceptable.
• To provide continued protection against risk of electric shock, connect to properly grounded outlet only.
• The Towel Warmer must be securely mounted to the wall. When possible, the Towel Warmer should be
attached to adequate blocking or framing.
• Installations where blocking or framing is not available must use appropriate wall anchors for mounting
directly to sheetrock.
1 Check all parts have
been supplied before
assembling the
Towel Warmer.
2 Place the Towel Warmer
face down on a suitable
surface. Secure mounting
supports onto the Towel
Warmer using the 6mm
Allen wrench supplied.
3 Position the Towel
Warmer to the wall in the
required final position and
mark around each of the
mounting supports.
4 Drill a 6mm hole x 40mm
deep at the center of each
of the marked mounting
support positions. Insert
a wall plug into each of
the holes and fix the wall
mounts as shown.
5 Secure the assembly
by tightening the Allen
screws on each of the
mounting supports
with the 3mm Allen
wrench supplied.
6 Plug in the Towel Warmer
and switch it on.
7 Depending on room
temperature, it may take
up to 60 minutes for the
Towel Warmer to reach
optimum temperature.
1 2
3
4
5
Installation Instructions
MYSON
Code A B C Voltage Watts Weight
WRBY04 24” 46” 4-1/4” 120V 45W 7 lbs
WRBY10 24” 15-1/2” 4-1/4” 120V 120W 25 lbs
WSPH14 24” 44” 5” 120V 140W 12 lbs
WSPH19 24” 44” 5” 120V 190W 14 lbs
WSPH26 24” 59-1/2” 5” 120V 250W 18 lbs
WDIA05 20” 16-1/2” 5-1/4” 120V 40W 6 lbs
WDIA08 20” 30” 5-1/4” 120V 100W 7 lbs
WDIA12 20” 45-1/8” 5-1/4” 120V 150W 12 lbs
WPRL08 24” 30” 4-1/4” 120V 110W 7 lbs
WPRL10 24” 36-5/8” 4-1/4” 120V 140W 9 lbs