Instructions for 1000DX-200,1001DX-200, 1003DX, 1005DX Speedster ® Please read before use. Register your product at http://www.mytee. com/support/register Model # 1000DX-200 p.3 1001DX-200 p.9 1003DX p.15 1005DX p.21 General information p.
1000DX-200 SPEEDSTER 1000DX-200 SPEEDSTER® FRONT 1000DX-200 SPEEDSTER® BACK 11 10 1 2 12 9 3 8 13 4 7 14 5 6 1. Switch plate 2. Easy faucet fill 3. Solution tank lid 4. Front handle 5. Front vent 16 6. 5” locking casters 7. Solution tank 8. Female quick disconnect 9. 2” Male Cuff-Lynx™ 10. Recovery lid 11. Recovery tank 12. Push handle 13. Drain valve 14. Power cord 15. Back vent 1000DX-200 SPEEDSTER® ITEMS INCLUDED H110 Cuff-Lynx™ 2” Hose Adapter H375 - Hose Hanger (4) screws 15 16.
1000DX-200 SPEEDSTER 1000DX-200 SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1000DX-200 SPEEDSTER® SWITCHES Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® Cuff-Lynx™ vacuum hose port. Turn on Vac 1, Vac 2 and Pump switches.
1000DX-200 SPEEDSTER 1000DX-200 SPEEDSTER® DUMP VALVE 1000DX-200 SPEEDSTER® FILTER MAINTENANCE VACUUM STACK FILTER INTAKE FILTER Attach the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank. Check and clean the vacuum stack filters and solution tank filter daily by twisting off, rinsing with clean water and replacing. 1000DX-200 SPEEDSTER® LOCKING CASTERS MYTEE® SYSTEM MAINTAINER Locking casters help keep the machine remain stationary during use.
Order parts at: www.mytee.com/products/product.php?id=1000DX 6 A B C D E F H343 H296 2 3 G018 P732 H768 B107 H484 H256 B142 B135 B102 B656 43 44 45 46 47 48 49 50 51 52 Part prices are subject to change.
A B C D E F 8 14 17 8 13 16 15 59 to sol tank filter thru B216 12 11 21 22 18 23 24 10 7 20 26 27 25 7 9 28 8 7 6 8 6 29 4 1 3 6 2 37 38 19 37 34 35 40 31 42 19 43 5 23 34 32 to pump "IN" thru B186 35 33 32 5 41 7 44 45 35 55 34 20 46 47 48 49 27 59 58 57 8 56 19 8 4 40 46 53 24 to pump "OUT" thru AH120 54 52 50 51 3 64 60 63 64 65 66 67 3 46 4 68 36 5 to female qd thru B107 30 6 61 69 89 40 8 90 91
G 8 1/24/2014 Ground to Metal Plate L2 L1 115V Float Switch #E-370 relays N/O L2 L1 L2 L1 L1 L2 Pump C-322D G VAC 2 C-302LA G VAC 1 C-302LA G Cooling Fan C-317 1000DX-200 115 Volt System E-515 E-515 E-515 1000DX-200 SPEEDSTER WIRING SCHEMATIC
1001DX-200 SPEEDSTER 1001DX-200 SPEEDSTER® FRONT 1001DX-200 SPEEDSTER® BACK 1 2 12 11 10 9 3 8 13 4 7 14 5 16 6 1. Switch plate 2. Easy faucet fill 3. Solution tank lid 4. Front handle 5. Front vent 6. 5” locking casters 7. Solution tank 8. Female quick disconnect 9. 2” Male Cuff-Lynx™ 10. Recovery lid 11. Recovery tank 12. Push handle 13. Drain valve 14. Dual power cords 15. Back vent 1001DX-200 SPEEDSTER® ITEMS INCLUDED 15 16.
01DX-200 SPEEDSTER 1001DX-200 SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1001DX-200 SPEEDSTER® SWITCHES Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® Cuff-Lynx™ vacuum hose port. “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch.
1001DX-200 SPEEDSTER 1001DX-200 SPEEDSTER® FLOAT SWITCH 1001DX-200 SPEEDSTER® DUMP VALVE The Speedster® is equipped with an electronic float switch inside the recovery tank. The recovery float switch is activated by rising water to prevent suction into the vacuum stacks damaging the motors. Attach the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank.
Order parts at: www.mytee.com/products/product.php?id=1001DX 12 A B C D E F Part prices are subject to change.
A B C D E F 20 21 24 24 26 19 25 27 8 23 6 22 8 59 to female QD thru B107 28 18 17 16 7 7 31 35 to pump "OUT" thru B136 15 30 73 to sol tank filter thru B216 13 14 29 12 33 34 11 10 35 6 32 36 16 9 37 to heater "IN" thru AH156 6 7 8 6 38 6 8 41 5 40 39 4 48 1 49 5 5 3 2 46 47 50 45 51 43 34 53 46 to pump "IN" thru B186 44 43 45 52 42 73 37 55 72 4 4 71 70 8 56 54 7 69 57 68 8 58 52 67 46 45 28 66 59 1
Power In 2 C322D L2 C302LA Vacuum 1 C302LA L2 Vacuum 2 GND L1 L2 Pump 115 Volt Thermal Switch Thermal Switch Heater 1 1000W L2 L1 A901 GND GND L1 SW E-515 SW E-516 Thermal Switch Speedster 1001DX-200 Heater 2 1000W GND L1 SW E-515 14 SW E-515 115V Thermal Switch L2 L1 A901 GND Power In 1 E-370 Cooling Fan C317 L1B L2B Float Switch Service Light E-564 Ground to Metal Plate L1A L2A 1001DX-200 SPEEDSTER WIRING SCHEMATIC
1003DX SPEEDSTER 1003DX SPEEDSTER® BACK 1003DX SPEEDSTER® FRONT 10 1 11 9 2 12 8 3 13 4 7 14 5 1. Switch plate 2. Easy Faucet Fill 3. Solution lid 4. Front handle 5. Front cooling fan 17 6 6. Pressure Regulator 7. Solution tank 8. Female QD with Prime Valve 9. 2” Male Cuff-Lynx™ 10.Recovery lid 16 11. Push handle 12. Recovery tank 13. Drain valve 14. Dual Power cords 15. 12” Rear wheels 15 16. Back vent 17.
1003DX SPEEDSTER 1003DX SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1003DX SPEEDSTER® SWITCHES Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® Cuff-Lynx™ vacuum hose port. “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch. To activate heat, use lower right switch.
1003DX SPEEDSTER 1003DX SPEEDSTER® FILTER MAINTENANCE 1003DX SPEEDSTER® FLOAT SWITCH VACUUM STACK FILTER INTAKE FILTER Check and clean the vacuum stack filters and solution tank filter daily by twisting off, rinsing with clean water and replacing. The Speedster® is equipped with an electronic float switch inside the recovery tank. The recovery float switch is activated by rising water to prevent suction into the vacuum stacks damaging the motors.
Order parts at: www.mytee.com/products/product.
A B C D E F 15 18 8 17 8 16 14 23 24 25 37 21 22 26 to pump "OUT" thru AH184 13 12 20 27 4 6 28 10 11 29 6 7 19 30 29 to female QD thru B107 29 to heater "IN" thru B107 7 31 31 9 36 8 8 7 6 35 29 32 37 38 5 34 9 39 7 40 4 33 31 12 29 12 49 1 6 113 2 3 58 42 38 47 48 57 to pressure gauge thru AH203 41 6 56 45 40 38 44 8 60 54 42 61 50 to sol tank filter thru B186 46 55 59 39 40 43 39 53 5 47 to pump "IN"
Power In 2 L2 C313 Pump L2 C302LA Vacuum 1 115 Volt C302LA L2 Vacuum 2 Thermal Switch Thermal Switch Thermal Switch Heater 1 600W L2 L1 A905A GND Speedster 1003DX GND L1 GND L1 SW E-515 SW E-516 L2 Heater 2 1000W GND L1 SW E-515 20 SW E-515 GND A901 115V Thermal Switch L1 Power In 1 E-370 Cooling Fan C317 L1B L2B Float Switch Service Light E-564 Ground to Metal Plate L1A L2A 1003DX SPEEDSTER WIRING SCHEMATIC
1005DX SPEEDSTER 1005DX SPEEDSTER® FRONT 1 1005DX SPEEDSTER® BACK 10 11 9 2 12 8 3 18 7 4 13 5 14 6 17 1. Switch plate 2. Easy faucet fill 3. Solution lid 4. Female quick disconnect 5. Front handle 6. Front vent 7. Pressure Regulator 8. Prime Valve 9. 2” Male Cuff-Lynx™ 10.Recovery lid 15 16 11. Push handle 12. Recovery tank 13. Drain valve 14. Dual Power cords 15. 12” Rear wheels 16. Back vent 17. 5” locking casters 18.
1005DX SPEEDSTER 1005DX SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1005DX SPEEDSTER® SWITCHES Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® Cuff-Lynx™ vacuum hose port. “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch. Bottom right switch has no use.
1005DX SPEEDSTER 1005DX SPEEDSTER® FILTER MAINTENANCE 1005DX SPEEDSTER® FLOAT SWITCH VACUUM STACK FILTER INTAKE FILTER Check and clean the vacuum stack filters and solution tank filter daily by twisting off, rinsing with clean water and replacing. The Speedster® is equipped with an electronic float switch inside the recovery tank. The recovery float switch is activated by rising water to prevent suction into the vacuum stacks damaging the motors.
Order parts at: www.mytee.com/products/product.php?id=1005DX 24 A B C D E F H378 H210 H213 H201 H216 H316 H342 H666 7 8 9 10 11 12 13 14 B105 B260A B259A B644 PH615-37 H347 B160 B652 B107 B643 29 30 31 32 33 34 35 36 37 38 Part prices are subject to change.
A B C D E F 8 to sol tank 10 9 7 6 32 33 28 4 8 11 5 30 31 34 35 filter thru B186 8 8 3 27 29 12 2 28 36 1 30 31 37 8 11 11 13 8 26 40 37 7 41 38 14 39 67 to pressure gauge thru AH120 7 15 25 24 57 16 to female QD thru AH203 17 23 22 6 21 6 18 20 19 45 44 5 5 43 46 42 66 64 65 64 64 64 63 28 47 48 62 54 61 4 35 to pump "IN" thru B160 4 59 54 38 to pump "OUT" thru B643 60 53 49 50 58 55 51 56 52 37 71 72
E-564 G 26 L2 L1 G L2b L1b light L1a L2a L2 L1 L2 Ground to Metal Plate L1 L2 115V L2 relays #E-370 Float Switch L1 N/O L2 Pump VAC 2 VAC 1 L1 C-313A G C-302A G C-302A G Cooling Fan C-317 1005DX 115 Volt System E-515 E-515 E-515 1/27/2014 1005DX SPEEDSTER WIRING SCHEMATIC
GENERAL INFORMATION Dear Customer: specify the Model and Serial Number when discussing your machine. Congratulations on the purchase of your new Speedster® Extractor. As you are already aware, the scene of the equipment world is becoming more high tech, and we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality and technology. Name Plate The Model and Serial Number of your machine are shown on the name plate located on the inside of the machine.
GENERAL INFORMATION 17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage. 18. When cleaning and servicing the machine, local or national regulations may apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids. 19. Do not leave operating unattended. Please note: Your pump features a pressure switch, to protect vital components.
GENERAL INFORMATION PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE. 4. If electronic switch is shut off, empty vacuum tank of all wastewater. 5. If water is coming out of the vacuum motor, use a low foaming detergent. 6. Clean upholstery tool or floor wand jets.
Mytee Products, Inc. 3. When Warranty is approved, the Distributor’s account will be credited for the replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s) to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be credited for any parts sent for this claim.
NOTES 31
NOTES 32
