Instructions for 8070 Mytee-Lite™ Please read before use. Register your product at http://www.mytee.com/ support/register Model # Set up p. 2 General information p. 6 Parts & pricing p. 9 Wiring diagram p. 11 Notes p.12 Serial # Form # ADP-8070 5-14 13655 Stowe Dr., Poway, Ca.
8070 MYTEE-LITE™ FRONT BACK 1 8 2 3 9 4 10 11 7 5 14 6 13 12 8. Basket 9. Recovery tank drain 10. Service latch 11. Switch plate 12. 25’ single power cord 13. 6” wheels 14. 2” casters 1. Hose hanger 2. Recovery tank lid 3. Cuff-Lynx™ vacuum hose connector 4. Open fill for solution tank 5. Solution hose connector 6. Solution tank drain 7.
8070 MYTEE-LITE™ FILL SOLUTION TANK EMPTY SOLUTION TANK To fill the solution tank, use a bucket to pour water into the tank’s opening located at the front of the unit. You can also use the easy faucet fill also located at the front of the unit. For best results, fill with warm water (140o F). To empty any remaining water in the solution tank, remove cap which is located at the front of the solution tank.
8070 MYTEE-LITE™ VACUUM SWITCH HEATER SWITCH Turn on vacuum motor and begin cleaning. For best results make two dry passes for every wet pass. Release tool trigger. Turn on heater. Wait 8 – 10 minutes for unit to pre-heat. Once heated, re-key upholstery tool until hot water begins flowing. Once hot water is flowing, release trigger and pre-heat an additional 4 – 5 minutes. RECOVERY TANK DRAIN VACUUM STACK FILTER Located at the rear of the Mytee-Lite™ is a bucket high drain valve.
8070 MYTEE-LITE™ SYSTEM MAINTAINER SERVICE LATCH Weekly flushing of the solution system with Mytee System Maintainer helps keep lines clean and prevents chemical build-up, improving pump life, performance and pressure. To open lower housing flip-up latch that is located in the back of the unit. Twist counter clockwise for release. To close unit, place latch, twist clockwise and press latch to secure.
GENERAL INFORMATION Dear Customer: Unpacking the Machine Keep in mind that the 8070 Mytee -Lite™ is a machine, so neglect or abuse will cause unnecessary damage and void the warranty. However with simple maintenance the 8070 will give quality performance for many years to come. Caution and Warnings Congratulations on the purchase of your new 8070 Mytee -Lite™. As you are already aware, the scene of the equipment world is becoming more high tech, and we at Mytee Products Inc.
GENERAL INFORMATION Maintenance Schedule Setup 1. Fill solution tank with water or approved cleaning agent. For best results, fill with warm water (140o). Replace vacuum tank. Flammable materials can cause an explosion or fire. Do not use flammable solutions or materials in tank(s). FOR SAFETY: When using machine, follow mixing and handling instructions on chemical containers. ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
GENERAL INFORMATION Q: Are the pumps re-buildable for the 8070? A: Yes, both the seals and the pistons have repair kits available. Please see the pump manual that shipped with your machine for the maintenance schedule. If any provision or portion of this limited warranty policy is found to be unenforceable, then the remaining provisions and portions shall remain valid and enforceable.
Order parts at: www.mytee.com/products/8070-mytee-lite-ii-automotive-detail-extractor/#.UtltKv16ho5 9 A B C D E F H203 H210 H216 H213 13 14 15 16 H427 H279 H042 29 30 31 32 Part prices are subject to change.
A B C D E F 8 8 7 6 5 7 7 4 4 3 12 11 10 9 8 2 6 6 1 3 4 5 5 21 22 23 22 50 to pump "IN" thru B106A 20 17 19 29 24 36 4 16 20 15 18 to sol tank thru B119 25 4 14 13 35 37 32 33 38 29 27 43 28 27 14 46 53 to heater "IN" thru 41 44 3 30 4 31 40 34 39 45 3 27 42 47 4 45 to pump "OUT" thru AH157 53 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC.
1/15/2014 L2 L1 G Primary Cord 11 E-515 E-515 E-515 1000 Watt Heat G L1 L2 Pump VAC L2 C-305 C-302P L1 G G 8070 115 Volt System To Metal Plate 8070 MYTEE-LITE™ WIRING DIAGRAM
NOTES 12
