8X96 ADC and DAC User Manual Page 1 of 54 MYTEK DIGITAL 8X96 Series ADC and DAC User Manual Rev. 9/2004 © 2004 Mytek Inc. for current literature, manuals and online email support check http://www.mytekdigital.
8X96 ADC and DAC User Manual Page 2 of 54 This manual may be updated Download the newest version at: http://www.mytekdigital.com/8x96manual.pdf For technical support, technical tips and support check: http://www.mytekdigital.com or contact Mytek Inc. tech support at: techsupport@mytekdigital.com or at: tel. (646)-613 1822 fax. (212)-202 5331 Mytek 151 Lafayette Street 3rd Fl New York NY 10013 USA for current literature, manuals and online email support check http://www.mytekdigital.
8X96 ADC and DAC User Manual Page 3 of 54 Contents: General description………………………………………………………… 6 8X96 ADC Quick Start…………………………………………………………. 6 Analog input alignment…………………………………………… 7 Signal Flow………………………………………………………… 8 Features…..………………………………………………………… 9 Sampling frequencies and External synchronization ..…….. 9 Digital Inputs, Outputs and Synchronization………………. 10 SuperShaper-HR ™ Noise shaping and dithering………….. 12 Digital format conversion……..……………………………..
8X96 ADC and DAC User Manual Page 4 of 54 Bit splitting (MRX ™) and sample splitting (S/MUX ™)….. 29 Special DIP Switch Options…………..…………………….. 30 Specifications…………..……..…………………………….. 33 Digital Inputs, Outputs and Daughter cards….…………………………….. 34 Hi-Speed AES/EBU interface (Standard)…… ……..……………… 36 Optional “MDM” DIO Interface Daughter Cards…………………..
8X96 ADC and DAC User Manual Page 5 of 54 8X96 Series Converters – General description The MYTEK 8X96 series consists of two 2U units- the 8X96 ADC and the 8X96 DAC. They provide very high performance 24 bit 96 kHz conversion comparable to the most expensive mastering converters ( DR=120 dB, audiophile signal path). These units can be used as stand-alone devices for variety of studio applications such as 5.1 DVD mastering, multitrack recording and whenever high quality conversion is required.
8X96 ADC and DAC User Manual Page 6 of 54 8X96 ADC – Quick Start High performance SuperShaper HR ™ noise shaping algorithm provides extremely transparent and ADC sync clock can be either internal (preffered for effective wordlenght reduction preserving practically sound quality) or external wordclock. The 75 Ohm all 24 bit resolution on 20 bit output and most of it on termination resistor ( default=off) can be switched 16 bit out. See “Noiseshaping”. on by internal jumpers next to the BNC jack.
8X96 ADC and DAC User Manual Page 7 of 54 8X96 Converters are microprocessor controlled and as such are subject to static interference. If unusual circumstances such as a lightning storm cause any malfunctions, reboot the unit. For further questions regarding setup and features contact your dealer or Mytek technical support. 8X96 ADC – Analog Input Alingment Before using the 8X96ADC you need to align its analog inputs. The alignment generally does not affect audio quality, only input sensitivity.
X96 ADC and DAC User Manual Page 8 of 54 8X96 ADC – Signal Flow W RD C K IN PU T EX T.
8X96 ADC and DAC User Manual Page 9 of 54 8X96 ADC - Features Sampling Frequencies and External Synchronization The Analog-Digital converters are implemented as 4 stereo pairs. They operate synchronously , i.e. all 4 converters always receive the same clock. As a result, all 8 digital outputs (or 4 stereo pairs of digital signals) are in sync and in phase. The converters need a sampling clock of any frequency btwn. 25-100 kHz.
8X96 ADC and DAC User Manual Page 10 of 54 8X96 ADC – Features Digital Inputs, Outputs and synchronization 8X96ADC comes equipped with hi-speed AES/EBU digital output and input standard. Additionally up to two daughter interface (MDM) cards can be installed. There are several different MDM cards available for Mytek 8X96. They are the same for both ADC and DAC: ADAT – Features 2 ADAT lightpipe inputs (2x 8chan@48k) and 2 ADAT lightpipe outputs.
8X96 ADC and DAC User Manual Page 11 of 54 and cleaned up from jitter. The data path is 24 bit. No noise shaping can be performed on digital input data. If a bit splitting method is used , a bit-split signal arriving at the digital input can be decoded and output digitally at the proper wordlength (see the next chapter). During normal operation, when the analog input (ADC) is selected as the signal source, the digital signal is present at both the AES outputs and the output of one the optional DIO card.
8X96 ADC and DAC User Manual Page 12 of 54 8X96 ADC – Features Mytek “SuperShaper-HR” ™ Noise Shaping & Dither The 8X96 A/D converter employs SuperShaper-HR ™ - a sophisticated psychoacoustically optimized noise shaping and dithering algorithm. SuperShaper-HR ™ th uses 9 order high resolution noise shaping filters with proprietary filter coefficients developed by Mytek Inc. The appropriate noiseshaping curve is programmed into noiseshaping filters for each selected sampling frequency.
8X96 ADC and DAC User Manual Page 13 of 54 effective. A noise shaped 20 bit, 96k signal sounds virtually as good as 24 bit, 96k. Thus using a 20 bit ADAT for 4 channel 20 bit, 96k recording (see S/MUX) can be very effective. The noise-shaping filters are automatically engaged at appropriate levels when either 16 or 20 bit output wordlenght is selected. If 24 bit output is selected, the noise-shaping filter is off.
8X96 ADC and DAC User Manual Page 14 of 54 “Optimal Noise Shaping and Dither of Digital Signals” Preprint Number: 2822 Convention: 87 1989-10 Author: Michael Gerzon Author: Peter G. Craven This paper discusses optimizing noise shaping, with or without dither, using filtered error-feedback round a quantizer. “Psychoacoustically Optimal Noise Shaping” Preprint Number: 2965 Convention: 89 1990-09 AES Journal Vol:Issue: 40:7/8 Page: 611 Year: 1992 Author: Robert A.
8X96 ADC and DAC User Manual Page 15 of 54 8X96 ADC – Features Digital Inputs, Outputs and synchronization Both ADC and DAC 8X96 Converters can perform digital format conversion between any installed format (MDM Daughter cards), including standard AES/EBU DIO. See “Digital Inputs, Outputs and Daughter cards) for current literature, manuals and online email support check http://www.mytekdigital.
8X96 ADC and DAC User Manual Page 16 of 54 8X96 ADC – Features S/MUX ™ sample splitting and Prism MRX™ bit splitting 8X96 Converters bridge the advantages of 24 bit and 24/96 technology with the technical abilities of older digital equipment. S/MUX ™ and MRX ™ sample and bit splitting techniques allow for use of 16, 20 and 24 machines to record larger bit depth and higher sampling rates.
8X96 ADC and DAC User Manual Page 17 of 54 8X96 ADC – Features 8X96 ADC - Special DIP Switch Options Both ADC and DAC units are equipped with a dip switch mounted on the main motherboard next to BNC wordclock jack. This switch allows tailoring certain features of the A/D converters to the actual system setup.
8X96 ADC and DAC User Manual Page 18 of 54 Truncate bits 17-24 on TDIF in (default OFF, default pass 24 bit) – This setting truncates lowest 8 bit on TDIF input, allowing only for 16 bit input resolution. We have implemented this setting after discovering that Tascam DA88 machine outputs “rubbish” on bits 17-24. Cloning MDM Connectors (default disabled) – This setting is active in S/MUX or MRX mode and with ADAT and TDIF cards only.
8X96 ADC and DAC User Manual Page 19 of 54 Machine A/B select switch can select the source to be either connector A or B. Cloning enabled, (88/96k, MRX MODE2–96 =3x20@88/96): Channels 1-3 are bit-split (MRX) . Channels 1-3 are output/input in MRX pairs on connector A and B simultaneously. Channels 4-8 are not used. Machine A/B select switch can select the source to be either connector A or B. Cloning enabled, (44/48k, MRX MODE1 =4x24@44/48): Channels 1-4 are bit-split (MRX) .
8X96 ADC and DAC User Manual Page 20 of 54 8X96 ADC – Specifications Conversion: Linear, 128x oversampling at 44.1/48kHz 64x oversampling at 88.2/96kHz Resolution: 24 bit Sample rates: 44.1kHz, 48kHz, 88.2kHz, 96kHz or wordclock 25-100kHz Dynamic Range: 120dB A-weighted, 117dB Total THD+Noise: -105dB (<0.
8X96 ADC and DAC User Manual Page 21 of 54 8X96 DAC – Quick Start Dual function leds. Normally leds display the wordlenght of the signal. If MRX is selected led display detected mode of MRX encoding and its compatibility with MRX switch setting. (see “Bitsplitting”) DAC sync source. Normally “DIG IN” . See “DAC - internal sync” if you need a completely jitter immune D/A conversion Input selector switch Some DIO interface cards such as ADAT and TDIF have 2 sets of 8 chan DIO - A and B.
8X96 ADC and DAC User Manual Page 22 of 54 house clock is used, make sure that the clocks are properly fed and terminated (75 Ohm) if necessary, especially for long cable runs. 8X96 Converters are microprocessor controlled and as such are subject to static interference. If unusual circumstances such as lightning storm cause a malfunction, try rebooting the unit. For further questions regarding setup and features contact your dealer or Mytek technical support.
8X96 ADC and DAC User Manual Page 23 of 54 8X96 DAC – Signal Flow W R DC K O U T PU T 4 S T ER EO 4 S TE R E O A E S O U T S AE S IN S W RD C K EX TR A C T C R Y S TA L O SC IL L ATO R OR 8 C H A N H I-SP EE D (U P TO 96K ) A E S/E B U D IG I/O (4 X L R PA IR S) (STA N D AR D ) IN T ER N A L / D IG IN SY N C SW ITC H CLOC K G EN E R ATO R AN ALO G OU T #7/ 8 S TE R E O 24 B IT D /A # 7/8 AN ALO G OU T #5/ 6 S T E RE O 24 B ITD /A # 5/6 AN ALO G OU T #3/ 4 S TE R E O 24 B ITD /A # 3/4 IN PU T S
8X96 ADC and DAC User Manual Page 24 of 54 8X96 ADC – Features Digital Inputs, Outputs and synchronization 8X96DAC comes equipped with hi-speed AES/EBU digital input and output standard. Additionally up to two daughter interface (MDM) cards can be installed. There are several different MDM cards available for Mytek 8X96. They are the same for both ADC and DAC: ADAT – Features 2 ADAT lightpipe inputs (2x 8chan@48k) and 2 ADAT lightpipe outputs.
8X96 ADC and DAC User Manual Page 25 of 54 and cleaned up from jitter. The data path is 24 bit. If a bit splitting method is used , a bitsplit signal arriving at the digital input can be decoded and output digitally at the proper wordlength (see the next chapter). During normal operation, the digital signal is present at both the AES outputs and the output of the optional DIO cards. The AES/EBU interface will pass through (from its inputs to outputs) even 4 asynchronous signals.
8X96 ADC and DAC User Manual Page 26 of 54 8X96 DAC – Features Jitter Immune Operation, Internal Sync, Wordclock Out In the normal mode DACs are always slaved to incoming digital input. Incoming clock is run through two PLL circuits for jitter reduction. The incoming data is present on all outputs with certain limitations regarding the AES/EBU asynchronous mode. (See “Asynchronous operations as 4 independent stereo DACs” below).
8X96 ADC and DAC User Manual Page 27 of 54 8X96 DAC – Features Asynchronous operations as 4 independent stereo DACs Digital to analog converters are implemented as 4 stereo pairs. They can operate synchronously or asynchronously. During synchronous operation all 4 converters always receive the same clock, meaning that all four data streams are in phase. This is always the case when the Daughter Card input is selected.
8X96 ADC and DAC User Manual Page 28 of 54 8X96 DAC – Features Digital Format Conversion Both ADC and DAC 8X96 Converters can perform digital format conversion between any installed format (MDM Daughter cards), including standard AES/EBU DIO. See “Digital Inputs, Outputs and Daughter cards) for current literature, manuals and online email support check http://www.mytekdigital.
8X96 ADC and DAC User Manual Page 29 of 54 8X96 DAC – Features Bit Splitting (Prism MRX™) and Sample Splitting (S/MUX™) The 8X96DAC bit splitting and sample splitting operates exactly as in the 8X96ADC (See: “Digital Inputs, Outputs and Daughter Cards- S/MUX, MRX”). for current literature, manuals and online email support check http://www.mytekdigital.
8X96 ADC and DAC User Manual Page 30 of 54 8X96 DAC - Special DIP Switch Options Both ADC and DAC units are equipped with a dip switch mounted on the main motherboard next to BNC wordclock jack. This switch allows tailoring certain features of the D/A converters to the actual system setup.
8X96 ADC and DAC User Manual Page 31 of 54 implemented this setting after discovering that Tascam DA88 machine outputs “rubbish” on bits 17-24. Cloning MDM Connectors (default disabled) – This setting is active in S/MUX or MRX mode and with ADAT and TDIF cards only. The cloning function is primarily intended for output to a backup machine and for easy A/B’ing of two sources.
8X96 ADC and DAC User Manual Page 32 of 54 Cloning enabled, (88/96k, MRX MODE2–96 =3x20@88/96): Channels 1-3 are bit-split (MRX) . Channels 1-3 are output/input in MRX pairs on connector A and B simultaneously. Channels 4-8 are not used. Machine A/B select switch can select the source to be either connector A or B. Cloning enabled, (44/48k, MRX MODE1 =4x24@44/48): Channels 1-4 are bit-split (MRX) . Channels 1-4 are output/input in MRX pairs on connector A and B simultaneously. Channels 5-8 are not used.
8X96 ADC and DAC User Manual Page 33 of 54 8X96 DAC – Specifications Conversion: Linear, 128x oversampling at 44.1/48kHz 64x oversampling at 88.2/96kHz Resolution: 24 bit Sample rates: 25-100kHz (dig. in sync), 44.1k, 48k, 88.2k, 96k (int. sync) Internal Clock Jitter: 10 ps Dynamic Range: 120dB A-weighted, 117dB Total THD+Noise: -100dB (<0.
8X96 ADC and DAC User Manual Page 34 of 54 Digital Inputs, Outputs and Daughter cards 8X96DAC comes equipped with hi-speed AES/EBU digital input and output standard. Additionally up to two daughter interface (MDM) cards can be installed. There are several different MDM cards available for Mytek 8X96. They are the same for both ADC and DAC: ADAT – Features 2 ADAT lightpipe inputs (2x 8chan@48k) and 2 ADAT lightpipe outputs.
8X96 ADC and DAC User Manual Page 35 of 54 During normal operation, the digital signal is present at both the AES outputs and the output of the optional DIO cards. The AES/EBU interface will pass through (from its inputs to outputs) even 4 asynchronous signals. The format conversion, however, requires pairs to be synchronous as only the clock of pair #1/2 is used for format conversion. If less than 4 pairs are used, at least one pair should be feeding channels #1/2.
8X96 ADC and DAC User Manual Page 36 of 54 Hi-Speed AES/EBU interface (Standard) Hi-speed AES/EBU interface is standard for both ADC and DAC converters. The interface is capable of transferring of signals up to 24 bit and sampling rates of 25100kHz. It is also possible to select either AES/EBU or optional MDM DIO as inputs. The digital signal is looped through to the AES outputs as well as the outputs of the optional interface. Any interface specific flags except emphasis are dropped.
8X96 ADC and DAC User Manual Page 37 of 54 TDIF Interface (with MRX ™ and S/MUX ™) TDIF MDM interface is equipped with two TDIF ports, A an B which allow to operate with either one or two Tascam MDM machines or interface to other Tascam equipment for up to 8 channels of I/O and signals up to 24/96. When Tascam MDM machines are used with the 8X96ADC, the ADC wordclock output has to be fed to the machine wordclock input and the machine has to be set to accept external wordclock and TDIF digital input.
8X96 ADC and DAC User Manual Page 38 of 54 8 TRACKS @ 24/96 USING 24 BIT TASCAM MDM M A C H IN E A TA S C A M DA88 OR DA78 1 6 B IT M D M M A C H IN E B TA S C A M DA88 OR DA78 1 6 B IT M D M TD IF A IN T D IF IN T E R FA C E W / M R X O FF (S A M P L =X 2 ) TD IF A OUT CHA N 1-4 8X96 ADC OR 8X96 DAC 8 TR A C K S @ 2 4 /9 6 CHA N 1-4 (O N E U N IT ) TD IF B IN C L O N IN G O F F SAM PL=X2 M RX M O DE1 TD IF B OUT CHA N 5-8 CHA N 5-8 1 2 3 4 5 6 7 A N A LO G O R D IG ITA L I/O Our fa
Page 39 of 54 8 TRACKS @ 24/48 USING 24 BIT TASCAM MDM M A C H IN E A TA S C A M DA88 OR DA78 1 6 B IT M D M O P T IO N A L SE CO ND BACKUP M A C H IN E TD IF A IN T D IF IN T E R FA C E W / M R X O FF (S A M P L =X 1 ) TD IF A OUT CHA N 1-8 8X96 ADC OR 8X96 DAC 8 TR A C K S @ 1 6 /4 8 CHA N 1-8 (O N E U N IT ) TD IF B IN C L O N IN G O N SAM PL=X1 M R X 0 FF TD IF B OUT 1 2 3 4 5 6 7 A N A LOG O R D IG ITA L I/O 8X96 ADC and DAC User Manual 8 RECOMMENDED DIP-SWITCH SETTINGS (DOUBLE
Page 40 of 54 6 TRACKS @ 20/96 USING 16 BIT TASCAM MDM W/MRX M A C H IN E A TA S C A M DA88 OR DA78 1 6 B IT M D M M A C H IN E B TA S C A M DA88 OR DA78 1 6 B IT M D M TD IF A IN T D IF IN T E R FA C E W / M RX M O DE1 (6X 2 0,S A M P L= X 2 ) CHA N 1-3 TD IF A OUT 8X96 ADC OR 8X96 DAC 6 TR A C K S @ 2 0 /9 6 CHA N 1-3 (O N E U N IT ) TD IF B IN C L O N IN G O F F SAM PL=X2 M RX M O DE2 TD IF B OUT CHA N 5-7 CHA N 5-7 1 2 3 4 5 6 7 A N A LO G O R D IG ITA L I/O 8X96 ADC and DAC User
8X96 ADC and DAC User Manual Page 41 of 54 M A C H IN E A TA S C A M DA88 OR DA78 1 6 B IT M D M O P T IO N A L SE CO ND BACKUP M A C H IN E TD IF A IN T D IF IN T E R FA C E W / M RX M O DE2 (4X 2 4,S A M P L= X 1 ) CHA N 1-4 TD IF A OUT 8X96 ADC OR 8X96 DAC 4 TR A C K S @ 2 4 /4 8 CHA N 1-4 (O N E U N IT ) TD IF B IN C L O N IN G O N SAM PL=X1 M RX M O DE1 TD IF B OUT 1 2 3 5 4 6 A N A LO G O R D IG ITA L I/O 4 TRACKS @ 24/48 USING 16 BIT TASCAM MDM W/MRX 8 7 RECOMMENDED DIP-SWITC
8X96 ADC and DAC User Manual Page 42 of 54 ADAT Interface (with S/MUX ™) ADAT MDM interface is equipped with two ADAT ports, A an B which allow to operate with either one or two ADAT MDM machines or interface to other ADAT compatible equipment for up to 8 channels of I/O and signals up to 24/96. ADAT interface uses clock embedded in the optical signal and no wordclock is required to operate the interface although it can be used when appropriate.
8X96 ADC and DAC User Manual Page 43 of 54 8 TRACKS @ 20/96 USING 20 BIT ADAT MDM A D AT IN T E R FA C E 8X96 ADC OR 8X96 DAC (S A M P L =X 2 ) ADAT A OUT M A C H IN E B A D AT 2 0 B IT M D M CHA N 1-4 8 TR A C K S @ 2 0 /9 6 CHA N 1-4 (O N E U N IT ) ADAT B IN C L O N IN G O F F SAM PL=X2 N S = 2 0 B IT ADAT B OUT CHA N 5-8 CHA N 5-8 1 2 3 4 5 6 7 8 RECOMMENDED DIP-SWITCH SETTINGS (DOUBLE POSITION MEANS IRRELEVANT) OFF ON 4 TRACKS @ 20/96 USING 20 BIT ADAT MDM M A C H IN E A A D AT
Page 44 of 54 8 TRACKS @ 16/48 USING 16 BIT ADAT MDM ADAT A IN A D AT IN T E R FA C E (S A M P L =X 1 ) ADAT A OUT O P T IO N A L SE CO ND BACKUP M A C H IN E CHA N 1-8 8X96 ADC OR 8X96 DAC 8 TR A C K S @ 1 6 /4 8 CHA N 1-8 (O N E U N IT ) ADAT B IN C L O N IN G O N SAM PL=X1 N S = 1 6 B IT ADAT B OUT 1 2 3 4 5 6 7 8 RECOMMENDED DIP-SWITCH SETTINGS (DOUBLE POSITION MEANS IRRELEVANT) OFF ON 8 TRACKS @ 24/48/96 USING MYTEK DAW 9624 ADAT A IN H A M M E R FA LL OR SO NO RUS S T U D IO PC
8X96 ADC and DAC User Manual Page 45 of 54 Sadie/ dual AES Interface Sadie/dual AES interface is (as of Nov 2000) not yet available. Once released the card will feature 2 sets of 8 channel AES/EBU I/O on two D25 connectors. The interface will allow interfacing with up to two Sadie 2496 cards for 8 channel of up to 24/96 signal.
8X96 ADC and DAC User Manual Page 46 of 54 Sonic HDSP/USP Interface Sonic HDSP/USP interface is (as of Nov 2000) not yet available. Once released the card will feature set of 8 channel of up to 24/96 I/O on a HDSP/USP compatible miniD68 connector for direct connection to Sonic PCI card. There will be an additional port B on a second miniD68 connector for daisy-chaining additional HDSP/USP compatible equipment.
8X96 ADC and DAC User Manual Page 47 of 54 S/MUX ™ encoder and decoder The S/MUX ™ sample splitting method was originally developed by Sonorus Inc, in order to provide means of transmitting 24/96 data over 48k ADAT lightpipe. S/MUX stands for “sample multiplexing”. S/MUX ™ sample splitting has been design to allow 96k operation using standard 48k ADAT interface transmission. where one high speed 96k channel is split between 2 48k channels (tracks).
8X96 ADC and DAC User Manual Page 48 of 54 1. The lowest numbered bchan has the earliest-time sample. 2. The next-lowest bchan has the next-earliest sample, and so on. 3. The S/MUX channel (schan) sample rate is an integer multiple (N) of the bchan rate (e.g. 2x, 3x, 4x,etc.) 4. The oversampling multiplier N is called the order of the schans, notated S/MUX N (e.g. S/MUX 2 for a 2x, 48KHz to 96KHz system). 5. The first group of bchans {1..N} represent the first schan. 6. The second group of bchans {N+1..
8X96 ADC and DAC User Manual Page 49 of 54 Prism MRX ™ encoder and decoder Mytek has acquired a license for use of the MRX ™ bitsplitting method, developed by Prism of U.K. and used in their popular MR2024T interface. MRX bitsplitting is intended to pack higher resolution signals onto 8 channels of Tascam 16 bit DA88 and DA38 machines. The following formats are possible: MODE1 - 4 channels of 24 bit @44/48k are packed onto 8 tracks of 16 bit.
8X96 ADC and DAC User Manual Page 50 of 54 Using the 8X96 ADC and /or DAC As a set of converters, the 8X96 ADC and DAC have a number of applications. The goal is always to get a substantial improvement of sound quality - the sound of your digital recorder is always determined by the converters - even a 16 bit ADAT can be turn into 24 bit, 96kHz stereo digital master recorder. The 8X96 sound quality is far superior to any stock piece of digital audio equipment.
8X96 ADC and DAC User Manual Page 51 of 54 Front end for AudioCube ® Front end for other DAWs Front end for Tascam MX-2424 ® Front end for Mackie HDR2496 ® Front end for Sony DMX—100R ® and other digital consoles Front end for DAW 8X96 Converters are one of the most flexible choices for a high performance hardware front end. Mytek focuses exclusively on the performance of the converters and therefore can offer a solution superior to any offered by a DAW manufacturer.
8X96 ADC and DAC User Manual Page 52 of 54 DAW9624 ™ package with Lynx AES16 or RME Hammerfall Mytek converters, can be found in the front end of many professional DAWs such as Sonic Solutions, Sadie and Protools 24. The superior performance of their 24 bit sound is fully appreciated by the users. Not everyone though, could enjoy benefits of high end 24 bit sound without spending a fortune on the DAW hardware.
8X96 ADC and DAC User Manual Page 53 of 54 Linux) and all general audio software packages available today. S/MUX interface drivers required for 24 bit 96kHz work are also available for almost every software package. To support S/MUX Mytek has developed appropriate ADAT lightpipe 24 bit, 96 kHz interface daughter card for our 8X96 ADC and DAC.
8X96 ADC and DAC User Manual Page 54 of 54 Warranty This 8X96 Series digital audio converter is warranted by Mytek to the original purchaser against defects in workmanship and materials used in manufacture for a period of one year from the date of purchase. Faults due to customer misuse, unauthorized modifications or accidents are not covered by this warranty. No other warranty is expressed or implied. Any faulty unit should be sent, shipping prepaid, to the manufacturer.
