Owner's Manual

DIGITAL AUDIO
To take advantage of the M15 HD’s high performance surround and digital
audio circuitry, it is advisable that its sets of Digital Audio input are selected.
There are three types of Digital Audio input for the M15 HD. These are
HDMI, Optical and Coaxial digital input. A fourth option is “O” whereby no
incoming digital audio signal is selected by the particular Source.
The desired digital audio input for a particular Source can be selected by
scrolling to “Digital Audio”, press [S] and then [D/F] to step through the
desired digital input source. After nalizing the desired type of Digital Audio
input, press [S] and then [D/F] again to select the specic Digital Audio
input.
The following are the sets of assignable Digital Audio input:
HDMI $ HDMI 1 - 6
Optical $ Optical 1 - 4
Coaxial $ Coaxial 1 – 4
NOTE
 Anincomingdigitalsignalpresentattheassigneddigitalinputwill
alwaystakeprecedenceovertheassignedanalogaudioinput,evenif
botharepresent.Tomaintaintheanalogaudioinputfortheparticular
Source,select“O”atthe“DigitalAudio”settingofthesame“Source”
menu.
VIDEO
There are four types of video input a particular Source could be assigned.
These are HDMI, Component, S-Video and Video input. Another option is
“O”. Select “O” if it is intended not to assign any video input to a particular
Source.
Navigate through the Video input selections by pressing [S] and then
[D/F] to step through the selections. The following are the sets of
assignable Video input.
HDMI $ HDMI 1 - 6
Component Video $ Component 1 - 3
S-Video $ S-Video 1 - 4
Video $ Video 1 - 4
IMPORTANT NOTE ABOUT THE VIDEO PERFORMANCE OF M15 HD
 TheM15HDutilizesanNAD-engineeredeld-programmablegatearray
(FPGA)thatiscapableofenablingtheconversionofanalogvideoto
digitalvideo.ThisallowsasinglecableconnectiontoyourTVforall
sourceswhilemaintainingthesource’snativeresolution.Interlaced
videoisconvertedtoprogressivescanoverHDMIallowingcomplete
compatibilitywithlatestHDTVs.
 TheM15HDalsosupportsHDMI1.4afeaturesthatincludecompatibility
withabroadrangeof3DandHDdigitalvideosourcesanddisplays.
A/V PRESET
A particular Source can be assigned a stored Preset. The parameters set up
in the selected Preset number will be adopted into the particular Source it
is assigned (Please refer to the separate section on “A/V Presets” for further
understanding of Preset settings).
Scrolling to “A/V Preset” and by pressing [S] and then [D/F], a Source could
be assigned a Preset number ranging from Preset 1 to 5.
If it is desired not to assign the particular Source a Preset setting, select
“None”.
TRIGGER OUT
Trigger Out feature for a particular Source is dependent upon the
congurations done in a separate menu on Trigger Setup (See “Trigger
Setup” below). If “Source Setup” is assigned to all three Trigger output
(Trigger Out 1-3) in the separate “Trigger Setup” menu window, a particular
Source can have the following Trigger Out combinations
Trigger Out: 1 $ 2 $ 1 + 2 $ 3 $ 1 + 3 $ 2 + 3 $ 1+2+ 3
These combinations are dependent upon the assignment of “Source Setup”
for Trigger 1 Out, Trigger 2 Out or Trigger 3 Out at the “Trigger Setup” menu.
Another option is “None” whereby the particular Source is not assigned any
Trigger Out.
For “Trigger Out” to become enabled and assignable at “Source Setup
(Normal View)” menu, make sure to carry out or note the following
beforehand
• In the separate “Trigger Setup” menu, assign Trigger 1 Out, Trigger 2 Out
or Trigger 3 Out to “Source Setup.”
• “Trigger Out” will not appear as an option at the Source Setup (Normal
View) menu if at the separate “Trigger Setup” menu, Trigger 1 Out,
Trigger 2 Out or Trigger 3 Out are all assigned to “Main, Zone 2, Zone
3, Zone 4, Zone 2+3+4, Main + Zone 2, Main + Zone 3, Main + Zone 4
or Main + Zone 234”; with not even one “Trigger Out” port allocated to
“Source Setup.”
SOURCE SETUP (TABLE VIEW)
The Source Setup (Table View) reects the settings made in the Source
Setup (Normal View) menu. All the Source settings are summarized and
displayed in tabulated form in the Source Setup (Table View).
Navigating through the Source Setup (Table View) via a combination
of [A/S] and then [D/F] buttons, one will have the benet of directly
changing the settings for “Audio”, “Video”, “Preset” and “Name” without
going back to the Source Setup (Normal View) menu.
Highlight a particular Source number and then, toggle [ENTER] button
to enable or disable said Source number.
OPERATION
USING THE M15 HD  SETUP MENU
17
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ