S70 SYSTEM REMOTE CONTROL OWNER’S MANUAL
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Set-up of the S70 remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Component Selection S100 or S170 preamp selection Activating and setting the clock Adjusting Display Contrast Using the NAD S70 Remote Control . . . . . . . . . . . . . . . . . . . . . . .
NAD S70 System Remote Control Menu & Sub-menu Structure Main Menu Preamp Selection (eg. S170 or S100) Contrast Adjustment Clock Setup Menu Timer Setup Menu System Setup Menu Component No.1 menu (eg. AMP) Timer Select Menu Component No.2 menu (eg. PREAMP) Component No.3 menu (eg. TUNER) Component No.4 menu (eg. CD) Timer Status Menu FIGURE 1 NOTE: Component menus are optional.
FIGURE 6 8
FIGURE 6a 9
FIGURE 6b 10
FIGURE 6c 11
FIGURE 6d 12
FIGURE 6e 13
FIGURE 7 14
FIGURE 8 15
FIGURE 9 16
INTRODUCTION Thank you for purchasing the NAD S70 System Remote Control. With the S70 you can control all components of your NAD Silver Series system. The S70 can easily be customised to suit your particular NAD Silver Series system and provides additional functionality such as a clock, Sleep and on/off timer. Although the S70 is primarily meant to complement the NAD Silver Series, it will also function with most remote controlled NAD products from the C Series.
Press any button (other than Volume Up/Down) to activate the display. In the Main menu, each category of Silver Series component is represented by its own icon. Refer to figure No.2. To set up the S70 for your system: • From the Main Menu on the remote control, press the button next to where it indicates "SYSTEM" in the display. • The display will change to System Set-up Menu. Refer also to figure No.
necessary to adjust contrast. • From the Main Menu, press the button next to "SYSTEM". • Press the button next to ">>" to increase contrast or "<<" to decrease contrast. • When the optimum contrast level has been set, press the button next to "EXIT" to return to Main Menu. USING THE NAD S70 REMOTE CONTROL The NAD S70 is a "menu-driven" remote control, where many of its buttons vary in function, depending on which Menu was selected. The display next to these buttons indicates which functions are available.
menus. • In the Main Menu, press the button next to component displayed you wish to operate, e.g. "AMP". • The appropriate Component Menu and its icon appear in the top of the display, the "AMP" Menu in this example, with all available functions will appear. Press the button next to the function desired in the display. See also figure No. 5. • Press the button next to "EXIT" again to return to the Main Menu from where you can select another component.
NOTES: Make sure that the S70 is located well within range of all components, otherwise the Sleep Timer function will function erratically or not at all. The Sleep function is available only if Clock function has been selected (indicated by tick-mark) in the System Set-up Menu. Refer to chapter "Set-up of the S70 Remote Control" above for information on activating and setting the clock.
TROUBLESHOOTING GUIDE Problem Remote control works intermittently or doesn’t work at all 22 Cause Solution • Battery flat or snap-on connector incorrectly attached • IR transmitter or receiver windows obstructed • IR receiver on components are in direct sun or very bright ambient light • Check or replace battery Sleep Timer and Timer functions can’t be activated • These functions are available only if clock is activated • Activate clock Although activated, Sleep Timer and Timer function do not work
www.NADelectronics.com ©2001 NAD ELECTRONICS INTERNATIONAL All rights reserved.