Owner's Manual
Table Of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- introduction
- IDENTIFICATION OF CONTROLS
- operation
- USING THE T 787 – MAIN MENU
- USING THE T 787 – SETUP MENU
- SETUP MENU
- CONTROL/HDMI setup
- SOURCE SETUP
- Source Setup (Normal view)
- Source Setup (Table VIEW)
- iPod SETUP
- Speaker Setup
- AUDYSSEY AUTO CALIBRATION
- Speaker Configuration
- Speaker Levels
- Speaker Distance
- Adjusting the Volume
- Adjusting Channel Levels ‘On the Fly’
- Zone Setup
- AMPLIFIER SETUP
- trigger setup
- Listening Mode Setup
- Dolby Setup
- DTS Setup
- DTS Surround Modes
- ENHANCED STEREO
- Display Setup
- A/V PRESETS
- LISTENING TO AM/FM RADIO
- LISTENING TO XM RADIO
- LISTENING TO DAB RADIO
- LISTENING TO YOUR iPod PLAYER
- USING THE HTR 8 REMOTE CONTROL
- Controlling the T 787
- Learning Codes from other Remotes
- Punch Through
- Copy a Command from another key
- Macro Commands
- Button Illumination Timeout
- CONFIGURING THE BACKLIGHT
- Factory Reset
- Delete Mode
- Loading Code-Libraries
- Search Mode
- Checking Code-Library Number
- Summary of the HTR 8 Modes
- USING THE ZR 7 REMOTE CONTROL
- USING IR CHANNEL
- REFERENCE
CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS
No sound from all channels. • AC power unplugged. • Check AC cable connection and outlet.
• Power not switched on.
• Outlet has no power.
• Mute function is activated. • Toggle [MUTE] button to deactivate Mute
function.
No sound from some channels. • Faulty/missing cables. • Check cables.
• “Speaker Conguration” channel (s) set to “OFF”. • Check “Speaker Conguration” menu.
No sound from surround channels. • No surround listening mode is engaged. • Select appropriate listening mode.
• Surround channels set to “OFF” on “Speaker
Conguration” menu.
• Correct “Speaker Conguration” or “Speaker
Levels” settings.
• Surround channels level set too low on
“Speaker Levels” menu.
No sound from Subwoofer. • Subwoofer is o, not powered or improperly
connected.
• Power up subwoofer, check subwoofer’s
AC outlet or check connections.
• Subwoofer set to “OFF” on “Speaker
Conguration” menu.
• Correct “Speaker Conguration” or “Speaker
Levels” settings.
• Subwoofer level set too low on “‘Speaker Levels”
menu.
No sound from Center channel. • Source is a 2/0 (etc.). Dolby Digital or DTS
recording without center channel.
• Play a known 5.1-channel recording or
select Dolby Pro Logic IIx Music mode.
• Center set to “OFF” on “Speaker Conguration”
menu.
• Correct “Speaker Conguration” or “Speaker
Levels” settings.
• Center level set too low on “Speaker Levels”
menu.
No Dolby Digital/DTS. • Source’s digital output is not connected to a
T 787 digital input.
• Check connections.
• Source component not congured for
multichannel digital output.
• Check source component setup.
T 787 does not respond to remote control
commands.
• Batteries are at or incorrectly inserted. • Check batteries.
• Infrared receiver (IR) window of T 787 or IR
transmitter of the remote control is obstructed.
• Check IR windows and ensure clear line-
of-sight from remote to T 787.
• T 787 front panel is in very bright sunlight or
ambient light.
• Reduce sunlight/room lighting.
No RDS information. • Station signal too weak. • Check station tuning. Adjust or replace
antenna.
• Station not transmitting RDS data. • Tune to an RDS station that supports
program-service name (PS mode) and
radio-text mode (RT).
Display shows “No Service List”. • DAB antenna not connected properly. • Check the connection and position of DAB
antenna.
• No DAB coverage in the area. • Call your local DAB broadcast providers for
coverage information.
Reset T 787 to factory default settings: Press and hold [ a SOURCE ] and [FRONT INPUT/MP] front panel buttons until “Factory Reset..complete.” is shown
in the VFD.
REFERENCE
TROUBLESHOOTING
46
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ