Owner's Manual

ManualsBrandsNAD Electronics ManualsAudioNAD Electronics T 787 A/V Surround Sound Receiver

Table Of Contents

1 STANDBY BUTTON

• Press this button to switch ON the T 787 from standby mode. The

Standby LED indicator will turn from amber to blue and illuminate

the VFD. Pressing the STANDBY button again turns the unit back to

standby mode.

• The T 787 can also be switched ON from standby mode by pressing

any of the front panel buttons.

NOTE

The rear panel POWER switch must be in the ON position for the Standby

button to activate.

2 STANDBY LED

• This indicator will light up amber when the T 787 is at standby

mode.

• When the T 787 is powered up from standby mode, this indicator

will illuminate blue.

• If a Zone (Zone 2, Zone 3 or Zone 4) is ON and STANDBY button

is pressed to switch the T 787 to standby mode, the VFD will be

extinguished but the STANDBY LED remains illuminated blue.

This indicates a Zone (Zone 2, Zone 3 or Zone 4) is still active. The

corresponding active Zone icon(s) will also remain displayed in the

VFD.

• In order to completely shut down the T 787 with Zone 2, Zone 3

and/or Zone 4 still ON, press and hold STANDBY button until the

STANDBY LED turns amber.

3 NAVIGATION and ENTER BUTTONS

The navigation ([d/f/a/s]) and [ENTER] buttons have various

applications specic to given modes. The middle round button is

designated as [ENTER] button; this is normally pressed to complete a

selection, procedure, sequence or other applicable functions.

AM/FM mode

Toggle [ENTER] button to switch between “Tune” and “Preset” mode.

Select “Tune” mode.

• Pressing momentarily the [a/s] button will manually scan the AM

or FM band.

• Press and hold [a/s] for more than 2 seconds to search up or down;

the T 787’s tuner will stop at the next suciently strong signal it

encounters.

• Note that this function “wraps” - that is, it will continue to search

from one end of the AM or FM band to the other until it stops at a

strong signal.

Toggle [ENTER] button to switch between “Tune” and “Preset” mode.

Select “Preset” mode.

• Use [d/f] to step up or down AM/FM Presets. Unused presets are

skipped over. Note that Presets must have been previously stored.

Refer also to the item about STORING PRESETS (AM/FM/XM/DAB) at the

LISTENING TO AM/FM RADIO section of the OPERATION page.

XM mode (120V version model only)

• Use the front panel [d/f] and [ENTER] buttons in combination

with the [MENU] button to select through applicable XM menu

options.

DAB mode (230V version model only)

• Use front panel [a/s] and [ENTER] buttons in combination with

[MENU] button to select through applicable DAB menu options.

4 MEMORY

• Press this button to store tuned AM, FM and digital radio stations to

the T 787’s 40 preset-memory locations. One can store a mix of any

AM, FM and digital radio stations to the 40 available presets.

5 INFO

• Show information as supplied by the applicable source.

• Toggle [INFO] button to display supplied information.

IDENTIFICATION OF CONTROLS

FRONT PANEL

NAD T787

a SOURCE s

VOLUME

DELETE

AM/FM/DBA SPEAKERS B TUNER MODE LISTEN MODE TONE TONE DEFEAT FRONT INPUT/MP

AV Surround Sound Receiver T 787

MEMORY INFO

10 11 12 13 14 15 16 17 18 19

2 3 4 5 6 7 8 9

4 5 6 97 8

A B C ED

13 14 15 16 1712

1 2 3

191110

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ