VISO TWENTY VISO THIRTY Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Table of Contents I. Quick Start 4 II. More on Speaker Positioning A. Main Speakers B. Surround Speakers C. Subwoofer D. Wall Mounting 5 III. Additional Details on Configuring Your VISO System A. Important B. Selecting Speaker Wire C. Configurations D. Tighten Terminals E. NAD VISO DVD Receiver Setup F. Subwoofer Level G. Subwoofer LED Indicator H. AC Power Switch 7 IV. Protecting Your Speakers 15 V. Cabinet Care 15 In Case of Problems 15 VI. VII.
Thank you for your purchase. The NAD VISO speakers are designed to deliver high performance in many uses, and we hope they add much enjoyment to your listening life. I. QUICK START A. Attach the supplied adhesive backed bumpers near the corners of the LR5’s and C20’s bottom surface to protect the finish of speakers and furnishings. B. Position LR5 speakers as symmetrically as possible, at a comfortable distance from your seating position—slightly closer to each other than they are to you.
II. MORE ON SPEAKER POSITIONING A. Main Speakers The three factors to adjust according to your own tastes—keeping in mind that you are the judge and the one(s) to be satisfied-are: 1. The closer you place speakers to room surfaces, the greater the proportion of bass in their sound, because of the “focusing” effects of nearby surfaces on lower, longer-wavelength frequencies.
horizontally and vertically. If you prefer the surround effect to be more diffused rather than pinpointed, aiming the speakers somewhat away from your ears probably will be more satisfying. You may want even to place them to reflect their sound off the sides or rear of you room rather than have them radiate toward you.
something with steady low frequencies (such as organ music) or continuous test tones, not movie material. Move around the room and note where the bass sounds best; if you place the subwoofer there and yourself in your chair, you should get the same bass performance. Bear in mind that the test only works if you have your ears as high off the floor as the subwoofer will be, so don’t be afraid to crawl around.
not to over-tighten and damage the connectors. E. NAD VISO DVD Receiver Setup NAD VISO FIVE If you're using an NAD VISO FIVE DVD Receiver connected to an NAD VISO THIRTY and NAD VISO TWENTY, you must configure the Speaker Settings to calibrate the frequency response of the system. The following steps will guide you in configuring your NAD VISO FIVE with respect to NAD VISO THIRTY and NAD VISO TWENTY speakers. Ensure that your NAD VISO FIVE is unplugged when you connect the speakers.
2. With “Audio Setup Menu” highlighted, press [ENTER] button to select “Audio Setup Menu” and correspondingly bring up the Audio Setup Menu OSD. Audio Setup Menu Listening Mode Input Settings Speakers Settings Speakers Distance Channel Levels Exit 3. Use the [? ] button to scroll down to “Speaker Settings”. Press [ENTER] to select “Speaker Settings” menu. 4. At “Speaker Settings” OSD menu and with “Front” speaker item highlighted, set “Front” speaker to “Small” by pressing [< ] button until “Small”.
remote to select Center speaker. Then by pressing the [< ] button set the level to -3dB. Channel Levels Front L 0dB Center -3dB Front R 0dB Surr L 0dB Surr R 0dB Subwoofer 0dB Do not Save & Exit Save & Exit 8. Press [? ] button to scroll down to "Save & Exit. 9. Press [ENTER] to save the new setting and at the same time exit the Channel Levels menu. Press [SETUP] button to completely exit the Setup menu OSD. 10.
the supplied HTR 6 remote control. Since the remote control will be the primary controller for most cases, the following procedures are all made with reference to the use of the appropriate HTR 6 button controls. Listening Mode 1. Using the HTR 6 remote control, press the [SETUP] button. The SETUP menu On-Screen-Display (OSD) will be shown in your connected TV/Monitor. Setup Menu Audio Setup Menu Video Setup Menu OSC Language Exit 2.
4. While at the “Listening Mode” menu item, use the [< ] button to select “DVS Reference” – this is the calibrated listening mode setting when using the NAD VISO TWENTY speakers. Listening Mode Mode DVS Reference Do not Save & Exit Save & Exit 5. Use the [? ] button to scroll down to the “Save & Exit” menu item. Press [ENTER] to save the new settings and at the same time exit the Listening Mode menu. Press [SETUP] button to completely exit the Setup menu OSD.
Audio Setup Menu Listening Mode Input Settings Speakers Settings Channel Levels Exit 3. Press [ENTER]. While at the “Front” menu item, use the [< ] button to select the “Small” setting - this is the calibrated Speaker Setting when using the NAD VISO TWENTY speakers. Speaker Settings Front Small Subwoofer On Enhanced Bass Off Do not Save & Exit Save & Exit 4. Use the [? ] button to scroll down to the “Save & Exit” menu item.
to clip and/or the bass output from the subwoofer is insufficient, this indicates that the volume on the subwoofer is set too low. In such a case, turn down the subwoofer level on the VISO receiver to -10dB and set the volume switch on the subwoofer to the +10dB position. Then by adjusting again the subwoofer level on the VISO receiver, set the desired bass level. G. Subwoofer LED Indicator When the LED is red this indicates a stand-by mode.
VI. IN CASE OF PROBLEMS A. If a speaker begins to sound distorted, or seems to be missing certain frequencies, check first to see whether playing at somewhat lower volume seems to clear up the problem. It can be especially important to turn down the volume right away if you have pushed an amplifier or receiver past its comfortable limits. B. Determine if the problem is the speakers, the electronics, or the wire connections.
disconnect and connect the subwoofer input signal. If the subwoofer power indicator color changes to green, the VISO receiver may not be sending a signal to the subwoofer. Ensure the VISO receiver is correctly configured to provide signal at the subwoofer output. Sounds distorted Lower volume if the subwoofer begins to sound distorted to determine if playback at a lower level solves the problem.
FIGURE 1 5.1 System with VISO FIVE VISO S10 120V Model Only VOLUME 0 db 120V 60HZ 1.6A AC FUSE T1.
FIGURE 2 2.1 System with VISO TWO VISO S10 120V Model Only VOLUME 120V 60HZ 1.6A AC FUSE T1.
VIII. SPECIFICATIONS VISO LR5 Compact Monitor FREQUENCY RESPONSE (Anechoic) On Axis @ 0° ± 3dB 75-23,000Hz Off Axis @ 30° ± 1.5dB 80-10,000Hz LF cutoff - 10dB 65Hz VISO C20 Centre VISO S10 Subwoofer 75-23,000Hz 80-10,000Hz 65Hz 36-150Hz AMPLIFIER POWER Continuous Dynamic Dynamic Peak Type 32Hz 110 Watts 140 Watts 280 Watts Class AB Discrete MOSFET Output Devices SENSITIVITY Anechoic Chamber Typical Listening Room (1W (2.
www.NADelectronics.com ©2009 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved.