Operation Manual
8 VOL [ ] : Press [ ] button to increase or decrease the loudness level. Release the button
when the desired level is reached. The VFD on the front panel will indicate the level set. For
NAD Receivers, the VFD will also show “Volume Up” or “Volume Down” while pressing SR 8’s . The
VOLUME buttons do not aect recordings made using the TAPE or RECORD OUT/ZONE 2 outputs
but will aect the signal going to the PRE OUT outputs (if applicable).
9 SPK A, SPK B : The [SPK A] and [SPK B] buttons engage or disengage the speakers connected
respectively to the Speakers A and Speakers B terminals. Toggle [SPK A] to switch ON or OFF the
speakers connected to the Speaker A terminals. Toggle [SPK B] to switch ON or OFF the speakers
connected to the Speaker B terminals. Press both buttons to engage both speakers.
10 TONE DFT : Tone Controls are enabled or disabled by pressing this button.
CD PLAYER CONTROL (for use with NAD CD Player): Set the DEVICE SELECTOR to “CD” in order to
gain access to these buttons. Some of the control buttons below are applicable only to specic
NAD CD Player models; check the owner’s manual of your NAD CD Player for control button
compatibility.
SCAN [ ] : Fast reverse/forward search.
[ ] : Open or close disc tray.
[ ] : Stop playback.
[ ] : Pause playback temporarily.
[ ] : Go to next track/le.
[ ] : Go to beginning of current track/le or to previous track/le.
[ ]: Start playback.
FOLDER/FILE [ ]: Select through folder list/Select through WMA/MP3 les.
ENTER: Select desired folder or WMA/MP3 le.
DISP: Show playback time and other display information.
RAN: Play tracks/les in random order.
RPT: Repeat track, le or whole disc.
PROG: Enter or exit program mode.
CLEAR: Delete programmed track/le.
CD: Select CD as the active source.
USB: Select USB as the active source.
OPT: Select optical input as the active source.
SRC: Toggle to select desired SRC mode.
TUNER CONTROL (for use with NAD AM/FM/DAB Tuner): Set the DEVICE SELECTOR to “TUN” in
order to gain access to these buttons. Refer to the corresponding labels printed in the remote
control faceplate and their respective assigned buttons to make use of these functions. Some of
the control buttons below are applicable only to specic NAD Receiver or Tuner models; check the
owner’s manual of your NAD Receiver or Tuner for control button compatibility.
AUTO TUNE: In DAB mode, press this button to automatically scan all available local stations.
TUNE [ ] or [ ] : Step up or down between AM or FM frequencies.
PRESET [ ] or [ ] : Step up or down between stored radio presets.
AM/FM/DAB: Select DAB, FM or AM band.
TUNER MODE: In FM mode, toggle between “FM Mute On” and “FM Mute O”. In DAB mode,
pressing this button will activate Dynamic Range Control (DRC), Station Order or other applicable
DAB menu options.
BLEND: Engage or disengage BLEND feature.
MEMORY: Save current station into preset memory.
DELETE: Press and hold for about 2 seconds and the selected preset memory is erased.
[ ] : In DAB mode, in combination with TUNER MODE or other compatible buttons, toggle
to select through DAB feature options like Dynamic Range Control, Station Order and other
appropriate DAB options.
ENTER: In AM/FM mode, toggle to select Preset or Tune mode. In DAB mode, press and hold to
check signal strength.
INFO: Repeatedly pressing this button will show information as supplied by the current radio
station. The applicable display contents include related DAB display information and RDS
broadcast data.
NOTE
For iPod player-specic control buttons, please refer to “CONTROL FEATURES” under “OPERATION
– LISTENING TO YOUR iPod PLAYER”.
IDENTIFICATION OF CONTROLS
REMOTE CONTROL
12
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ