Owner`s manual

CD-R AND CD-RW AUDIO DISCS
The C 545BEE can play back CD-R or CD-RW audio discs that have been
recorded on a computer or CD recorder. The quality of CD-R or CD-RW
audio discs varies widely which may aect playability. Some factors that
aect playability:
• The quality of the disc itself. Generally speaking, CD-R or CD-RW blanks from
well-renowned companies give better results than unbranded ones.
• The quality of CD-recorder or computer CD re/writer. Some recorders
and writers produce better results than others.
• The CD-R and CD-RW were created with high-speed writing. In general,
the quality of a CD-R or CD-RW is better when produced at a lower
speed against a higher speed on the same recorder or re/writer.
PLAYING MP3/WMA FILES
The C 545BEE can play MP3/WMA formatted recordings on CD-R or CD-RW
discs. You may mix any of the le types on the disc. Using the CD 8 remote
control, one can select through the MP3/WMA folders and les as well as
start playback through the following steps
1 Load the applicable disc.
2 Press [FOLDER ] to select desired folder. Press [ENTER].
3 Press [FILE ] to select desired le number. Press [ENTER] to start
playback.
NOTES
• The le number is recognized per disc, not per folder – that is, the
number assigned to each le corresponds to their sequence in the disc.
• If you want to select le number “119” in a disc where there are 100 or
more MP3/WMA les, press “1” twice and then “9.”
IMPORTANT NOTICE
Customers should note that permission is required in order to download
MP3/WMA les and music from the Internet. NAD ELECTRONICS
INTERNATIONAL has no right to grant such permission. Permission
should always be sought from the copyright owner.
PROGRAMMING
The program function enables you to store your favorite tracks from any
disc in the player memory. When programming a sequence of tracks, the
C 545BEE must be in STOP mode. Using the CD 8 remote control, enter your
desired program sequence through the following steps
1 Press [PROG]. The display indicates “P01 T000”. The “000” in the “T000”
keeps on blinking, meaning that the player is awaiting the rst Program
entry.
2 Use the Direct-Entry numeric keypad buttons to enter the rst track
in your planned sequence. Upon entering the track number, the VFD
will briey show the total number and total time of the currently
programmed tracks like “01 3:25”.
3 The display will revert to show “P02 T000,” indicating that the player is
ready for your second program entry. Upon entering the second track,
the VFD will again briey show the total number and total time of the
currently programmed tracks like “02 6:45” – “02” indicates that there are
now a total of two programmed tracks and “6:45” is the total playback
time of both programmed tracks.
4 Repeat steps 2 and 3 to select and store other track numbers in
memory, up to a maximum of 40 entries. If you attempt to program
more than 40 tracks or les, “P-FULL” will be displayed in the VFD.
5 Press [PROG] to end or nalize the program – the VFD will show the last
programmed number and track.
6 Press [ ] to start program playback.
NOTES
• Programming of MP3/WMA les is the same as above procedure.
• If you want to select le number “119” in a disc where there are 100 or
more MP3/WMA les, press “1” twice and then “9.”
• Pressing [STOP] key at any time during the programming procedure will
put to a STOP to the sequence and clear all the currently programmed
tracks or les. VFD will revert back to displaying the total number of
tracks and total playback time for audio CD and total number of les for
MP3/WMA.
• Pressing [STOP] key twice during program playback will result to having
the whole program list deleted.
REVIEW/EDIT PROGRAM LIST
1 Initiate review of your programmed entries by pressing [PROG].
• If you are still in programming mode, press [PROG].
• If during program playback, press [STOP] once, then [PROG].
2 The VFD will show the rst Program Number and the corresponding
“blinking” programmed track.
3 To change the programmed track of a particular sequence, use the
Direct-Entry numeric keypad buttons. Press [SKIP ] to move
forward or backward the programmed tracks as well as review the list
and change if so desired.
4 If you want to delete a particular program sequence during program
review, press [CLEAR] key.
5 After nalizing your program changes or completing your review, press
[PROG] again.
PROGRAM PLAYBACK
1 To play the stored program, press [PLAY] while you are in “PROGRAM”
mode. “PROG” icon will appear in the display, indicating that a stored
program is being played. During Program Play, the SKIP buttons will
access only the tracks in the program list.
2 If you want to play only a portion of a stored program, initiate play and
press SKIP to jump over the programmed tracks that you don’t want to
hear.
STOP OR DELETE PROGRAM
1 To terminate Program play, press [STOP] once. The stored track list remains
in memory. If you want to play the program again, simply press [PLAY].
2 To clear the program memory, perform any of the following steps
• Press [STOP] twice during program playback.
• Press [OPEN] to open the disc tray.
• Switch OFF the C 545BEE by pressing the Standby button.
OPERATION
USING THE C 545BEE  FEATURES
11
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ