Owner`s manual
A wireless remote control is provided with your compact disc player,
enabling you to operate playback functions from the comfort of your chair
or from virtually anywhere in the room. For reliable operation there should
be a clear line-of-sight path from the remote control to the front of the CD
player. If the player does not respond to remote commands, it may be that
this line-of-sight path is obstructed by clothing, paper or furnishings.
Most of the buttons on the remote control handset have the same eect as
the corresponding buttons on the front panel of the player. In addition, the
handset is equipped with some extra buttons like the following function
keys.
NUMERIC KEY PAD
Using the direct-entry numeric keypad (0 to 9) causes the C 545BEE to jump
directly to the beginning of a numbered track and commence play. Thus, to
play Track 5, simply press “5”. To play Track 20, press “2” and “0”.
RPT A-B
To repeat a sequence, implement the following procedures:
1 Press [RPT A-B] at your chosen starting point.
2 Press [RPT A-B] again at your chosen end point. The repeat sequence
begins.
3 Press [RPT A-B] again to cancel the sequence.
DIMMER
Toggle to reduce, turn o and restore VFD brightness.
PROGRAM AND DELETE
Use [PROG] button to start, review, edit or exit programming mode. In
combination with [PROG] button, the [CLEAR] button allows the deletion of
a programmed track during program review or edit sequence. Refer also to
the item about “PROGRAMMING” at the “USING THE C 545BEE – FEATURES”
section of the “OPERATION” page.
FILTER
The [FILTER] button is used for selecting the bandwidth of the audio low
pass lter for the CD, MP3 and WMA media being played. The options are
NORMAL Bandwidth and SLOW Bandwidth. For some recordings the SLOW
Bandwidth may provide a wide frequency range and spatial feeling. Toggle
CD 8's [FILTER] button to select “NORMAL” or “SLOW” mode. “NORMAL FILTER”
or “SLOW FILTER” will be correspondingly shown in the VFD.
NORMAL: Select NORMAL bandwidth to engage a standard CD high-
pass lter slope for playback of CD, MP3, and WMA music through the
two channel stereo audio jacks.
SLOW: Select SLOW bandwidth to engage a gentle high-pass lter
slope for playback of CD music through the two channel stereo audio
jacks. This feature is particularly useful for higher bit rate recordings.
OPERATION
USING THE C 545BEE CD 8 REMOTE CONTROL
REFERENCE
TROUBLESHOOTING
CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS
No power. The power cord is disconnected.
•
Plug the power cord into the wall outlet
securely.
•
The power is ON, but the C 545BEE does
not work.
No disc is inserted.
•
Insert a disc.
•
The C 545BEE does not start playback. The disc is loaded upside down.
•
Reload the disc with the label side UP.
•
The disc is too dirty.
•
Clean the disc.
•
No sound. The equipment connected with the audio
cable is not set to receive CD signal output.
•
Select the correct input mode of the audio
receiver so you can listen to the sound from
the C 545BEE.
•
The power of the equipment connected with
the audio cable is turned o.
•
Turn on the equipment connected with the
audio cable.
•
Sound skips. The C 545BEE is subject to vibration or physical
shock from external sources.
•
Change the installation location.
•
The remote control does not work properly. The remote control is not pointed at the
remote sensor on the CD player.
•
Point the remote control at the remote
sensor of the CD player.
•
The remote control is too far from the CD
player.
•
Operate the remote control closer to the
CD player.
•
The remote control batteries are dead.
•
Replace the remote control batteries.
•
12
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ