Owner's Manual

NAD Electronics International reserves the right to change specifications or features without notice. NAD is a registered trademark of NAD Electronics International.
All rights reserved. No part of this publication may be reproduced, stored, or transmitted in any form whatsoever without the written permission of NAD Electronics
International. © 01/18 17-079 NAD Electronics International. www.NADelectronics.com
Specifications D3020 V2
All specs are measured according to IHF 202 CEA 490-AR-2008 standard. THD is measured using AP AUX 0025 passive filter and AES 17 active filter.
PREAMPLIFIER SECTION
LINE INPUT/PRE OUT
THD (20 Hz – 20 kHz) <0.01 % at 2 V out
Signal-to-Noise Ratio >106 dB (IHF, A-weighted, ref. 500 mV out, unity gain)
Channel separation >80 dB (1 kHz)
>70 dB (10 kHz)
Input impedance (R and C) 56 kohms + 100 pF
Maximum input signal >5.5 Vrms (ref. 0.1 % THD)
Output impedance 200 ohms
Input sensitivity 113 mV (ref. 500 mV out, Volume maximum)
Frequency response ±0.2 dB (20 Hz - 20 kHz)
Maximum voltage output - IHF load >4 V (ref. 0.1 % THD)
Bass EQ 6.0 dB at 80 Hz
PHONO INPUT/PRE OUT
THD (20 Hz – 20 kHz) <0.015 % at 2V out
Signal-to-Noise Ratio >82 dB (200 ohms source, A-weighted, ref. 500 mV out)
>76 dB (MM cartridge source, IHF; A-weighted, ref. 500 mV out)
Input sensitivity 1.15 mV (ref. 500 mV out, Volume maximum)
Maximum input signal at 1kHz >90 mVrms (ref. 0.1 % THD)
Frequency response ±0.3 dB (20 Hz - 20 kHz)
Note: The RIAA response is consistent with a pre-emphasis that is rolled off at 50kHz by a second order filter, such as used in Neumann cutting lathes.
LINE INPUT/HEADPHONE OUT
Signal-to-Noise Ratio >96 dB (32 ohms load; A-weighted, ref. 500mV out, unity gain)
Frequency response ±0.3 dB (20 Hz - 20 kHz)
Output impedance 100 ohms
Maximum headphone output 6.8V (300 ohms load)
GENERAL SPECIFICATIONS
LINE INPUT/SPEAKER OUT
Continuous output power into 4 and 8 ohms 30 W (ref. 20 Hz-20 kHz at 0.1% THD, both channels driven)
THD (20 Hz – 20 kHz) <0.01 % (at 1W, 4 and 8 ohms)
Signal-to-Noise Ratio >98 dB (A-weighted, 500 mV input, ref. 2.828 V out in 4 ohms)
Clipping power >50 W (at 1 kHz 4 ohms 0.1 % THD)
IHF dynamic power 8 ohms : 60 W
4 ohms : 100 W
2 ohms : 150 W
Peak output current >18 A (in 1 ohm, 1 ms)
Damping factor >300 (ref. 8 ohms, 20Hz to 6.5kHz)
Frequency response ±0.3 dB (20 Hz - 20 kHz)
Channel separation >75 dB (1 kHz)
>70 dB (10 kHz)
Input sensitivity 250 mV (for 30 W in 4 ohms)
Supports bit rate/sample rate up to 24 bit/192 kHz
Standby power <0.5 W
DIMENSION AND WEIGHT
Gross dimensions (W x H x D) 58 x 186 x 219 mm
2 5/16 x 7 3/8 x 8 5/8 inches
Net weight 1.4 kg (3.1 lbs)
Shipping weight 2.1 kg (4.6 lbs)
NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL. THE D 3020 V2 OWNER’S MANUAL MAY
BE SUBJECT TO CHANGE WITHOUT NOTICE. CHECK OUT WWW.NADELECTRONICS.COM FOR THE LATEST VERSION OF THE D 3020 V2 OWNER’S MANUAL.
* Gross dimension includes feet, volume knob and extended rear panel terminals. ** Non-metric measurements are approximate. NAD Electronics will not assume any liability for errors being made by retailers,
custom installers, cabinet makers, or other end users based on information contained in this document. Note: Installers should allow a minimum clearance of 55mm for wire/cable management.