NEDERLANDS Owner’s Manual SVENSKA DEUTSCH ITALIANO ESPAÑOL FRANÇAIS DirectDigital DAC Amplifier ENGLISH M32 РУССКИЙ ®
IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA 1. Read instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. FRANÇAIS CAUTION Marking and rating plate can be found at the rear panel of the apparatus. WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
INTRODUCTION TABLE OF CONTENTS ENGLISH IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 2 FRANÇAIS FRONT PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 MDC CLASSIC UPGRADE SLOTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION RESTORING M32 TO ITS FACTORY DEFAULT SETTINGS 1 Press and hold front panel’s “Main” display. SAVE THE PACKAGING Please save the box and the packaging that came with the M32. Should you move or need to transport your M32, this is the safest container to use.
IDENTIFICATION OF CONTROLS FRONT PANEL ENGLISH 2 FRANÇAIS 1 ESPAÑOL © NAD M32 ITALIANO 3 4 1 POWER INDICATOR • This indicator will be amber when the M32 is in standby mode. • When the M32 is powered up from standby mode, this indicator will change from amber to bright white color. DEUTSCH NEDERLANDS 2 o(STANDBY) • Touch the o (Standby) button on top of the unit to switch the M32 ON from standby mode. The Power indicator will change from amber to bright/white color.
IDENTIFICATION OF CONTROLS 1 2 3 4 5 6 ENGLISH REAR PANEL 7 OPT1 INPUT PHONO OPT2 L OUTPUT LINE 1 LINE 2 FRANÇAIS COAX2 M o d u l a r D e s i g n C o n s t r u c t i o n M o d u l a r D e s i g n C o n s t r u c t i o n M o d u l a r D e s i g n C o n s t r u c t i o n COAX1 PRE-OUT/SUBW L L L R R R MM SERVICE COMPUTER R AES/EUB IN © NAD M32 11 12 13 14 15 ESPAÑOL 10 ATTENTION! Please ensure that the M32 is powered off or unplugged from the main power source before m
IDENTIFICATION OF CONTROLS REAR PANEL ENGLISH FRANÇAIS 7 POWER • The POWER switch supplies the master AC mains power for the M32. • When the POWER switch is set to ON position, the M32 goes to standby mode as shown by the amber status condition of the front panel Power indicator. Press the front panel Standby button or HTRM 2’s remote control’s [ON] button to switch ON the M32 from standby mode.
IDENTIFICATION OF CONTROLS MDC CLASSIC UPGRADE SLOTS DD AP 1 (DIRECT DIGITAL ANALOG-PHONO) The delivery format of digital content is constantly changing in pure digital systems like the M32. Each of these formats typically requires specialized hardware and software, often with licensed IP and content copy protection. DD AP 1 uses high quality Analog-toDigital conversion to make analog sources compatible with M32’s pure digital circuitry.
ON ON ON OPERATION USING THE M32 OFF OFF OFF DEVICE SELECTOR DEVICE SELECTOR DEVICE MP SELECTOR ENGLISH MP MP NAVIGATING THE M32 FEATURES AND MAKING CHANGES Use the HTRM 2 or applicable touch panel display items to select Sources, navigate through the M32 features and access to other functions. The following are some of the key functions. DAC FEATURE/FUNCTION/ITEM TOUCH PANEL DISPLAY ON HTRM 2 DAC DAC ON Selecting Sources.
OPERATION DAC USING THE M32 ENGLISH MUTE Random playback. SLEEP SOURCE ON OFF DEVICE SELECTOR Repeat playback. 8 FRANÇAIS IN Press repeatedly to toggle random playback of current list, all folders or random off. MP RANDOM. DEVICE SETUPSELECTOR DELAY / must PICTURbe E Tset ESTto / ZMP. OOM OFF INON 10 ON PROGRAM CLEAR OFF REPEAT DEVICE SELECTOR DAC EQ TONE L.NITE SLEEP MP DEVICE SELECTOR MP Press repeatedly to toggle repeat playback - current file, all folders or repeat off.
OPERATION USING THE M32 ENGLISH DISPLAY MENU OPTIONS MODE The following display options are accessible via the touch panel display Main, Media, Mode, EQ and Setup. MAIN FRANÇAIS Use the Main screen to select a Source. Use the arrows to navigate to the required Source. In the following example the Main screen is displaying the Coax 1 information. The following listening modes, tailored for different types of recording or program material, are provided. ESPAÑOL ITALIANO Coax 1: Current Source. -20.
OPERATION h : Slide to adjust treble, bass or balance level. : Slide to turn ON or OFF Tone Controls. At OFF setting, tone controls (Treble and Bass) are disabled or defeated – Balance option remains available. * The exception may be some electrostatic speakers that have very low impedance at high frequency. The lower the HF impedance, the greater the deviation from flat response. SUB OUTPUT At “ON” Setting, all subwoofer settings are in effect. At “OFF” setting, all subwoofer settings are disabled.
OPERATION USING THE M32 ENGLISH SUB MODE • Set the subwoofer mode to either mono or stereo setting. Mono: Select this setting when using one subwoofer. At mono mode, the left and right channels are summed in the low pass subwoofer output to drive a single subwoofer. Stereo: Select this setting when using two subwoofers, one for the left channel and one for the right channel. FRANÇAIS MAIN FREQUENCY (40Hz to 200Hz and Full) MAIN TRIM (-12.0dB to 0.
OPERATION Sample Rate (48 kHz, 96 kHz, 192 kHz): Select the user’s preference for sample rate of the Analog-to-Digital Converter. Higher sampling rates allow for anti-aliasing filters to take effect further outside the audible frequency range and are generally considered to sound better, especially in the high frequencies. This option is applicable only for LINE 1 or LINE 2. DIGITAL OUTPUT Sample setup of two NAD products on the same Zone M32 and T 787 are both defaulted to IR Channel 0.
OPERATION OTHER FEATURES ENGLISH BluOS MENU FRANÇAIS BluOS “Menu” becomes available if the optional MDC BluOS is installed. BluOS “Menu” can be accessed directly from the touch panel display. Select “Menu” during BluOS playback as above. The following are the BluOS menu options – Info, BluOS Reboot, BluOS Factory Reset and Service Menu. SERVICE MENU Service Menu has two options - “BluOS Upgrade Mode” or “BluOS Service Mode”. BluOS UPGRADE MODE Select “Yes” to initiate BluOS upgrade mode.
OPERATION ENGLISH USING THE HTRM 2 REMOTE CONTROL The NAD HTRM 2 is ready to operate the M32 right out of the box, but it is really eight remotes in one. Each of the 8 Device Selector keys at the top of the handset can call up a new “page” of remote control codes to be transmitted by the remaining keys. You may “teach” codes from any infrared-remote controlled component, regardless of brand, to any or all of these.
OPERATION USING THE HTRM 2 REMOTE CONTROL ENGLISH If the Learn LED does not flicker amber you may need to vary the distance between the remotes. If the Learn LED turns red instead of green, the source remote command could not be learned on that attempt. FRANÇAIS Example: Learning “BD Pause” Position the HTRM 2 and your BD player’s remote as described above. 1 On the HTRM 2, simultaneously press-and-hold [BD] and [RES]; the Learn LED turns steady green.
OPERATION CONFIGURING KEY ILLUMINATION Mode DISP + Digit Key (0-9) Set key illumination timeout to number of seconds corresponding to digit key. Zero turns off the key illumination entirely. DISP + OFF Disable light sensor. Key illumination will turn on with any key press. DISP + ON Enable light sensor. To clear a macro, perform the above steps without entering any functions. DISP + ENTER Set the light sensor threshold to the current light level.
OPERATION USING THE HTRM 2 REMOTE CONTROL ENGLISH FRANÇAIS ESPAÑOL LOADING CODE-LIBRARIES SEARCH MODE The HTRM 2 can store a different library of default NAD codes for each of its Device Selector “pages.” If the original default library does not control your NAD CD player, BD player, or other component, follow the procedure below to change the code-library. 1 Begin by ensuring that the component you wish the HTRM 2 to control is plugged in and powered-up (“on,” not merely in standby).
OPERATION ENGLISH USING THE HTRM 2 REMOTE CONTROL BATTERY INSTALLATION FRANÇAIS 1 Use the flat or rounded end of a pointed tool to push open the pin of the battery cover. ESPAÑOL 2 Open the battery hatch. DEUTSCH ITALIANO 3 Insert the supplied four AA batteries. NEDERLANDS 4 Push the battery hatch until it clicks close. РУССКИЙ SVENSKA 5 Restore the battery cover.
REFERENCE SPECIFICATIONS ENGLISH All specs are measured according to IHF 202 CEA 490-AR-2008 standard. THD is measured using AP AUX 0025 passive filter and AES 17 active filter.
РУССКИЙ SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH
www.NADelectronics.com ©2017 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
