SVENSKA NEDERLANDS DEUTSCH ITALIANO PORTUGUÊS ESPAÑOL FRANÇAIS AV Surround Sound Receiver ENGLISH T 758 РУССКИЙ ® Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS ENGLISH SAVE THESE INSTRUCTIONS FOR LATER USE. NOTE TO CATV SYSTEM INSTALLER FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT. This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this out. FRANÇAIS The materials can be reused in accordance with their markings.
INTRODUCTION TABLE OF CONTENTS ENGLISH IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 2 INTRODUCTION FRANÇAIS GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 WHAT’S IN THE BOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INITIAL SETUP. . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION ENGLISH GETTING STARTED WHAT’S IN THE BOX FRANÇAIS Packed with your T 758 you will find • AM loop antenna • FM lead-type antenna • Detachable mains power cord • Audyssey microphone • AVR 4 remote control with 2 AA batteries • ZR 7 zone remote control with 3V CR2025 battery • T 758 Quick Start Guide ESPAÑOL SAVE THE PACKAGING Please save the box and all of the packaging in which your T 758 arrived.
IDENTIFICATION OF CONTROLS FRONT PANEL ENGLISH 1 2 3 4 5 6 7 8 9 AV Surround Sound Receiver T 758 FRANÇAIS a s ESPAÑOL A B C D © NAD T 758 PORTUGUÊS 10 11 12 ITALIANO DEUTSCH NEDERLANDS 1 STANDBY BUTTON • Press this button to switch ON the T 758 from standby mode. The Standby LED indicator will turn from amber to blue and illuminate the VFD. Pressing the STANDBY button again turns the unit back to standby mode.
IDENTIFICATION OF CONTROLS Distance: About 23ft (7m) from the front of the remote sensor. Angle: About 30° in each direction of the front of the remote sensor. 8 a SOURCE s • Toggle through the input selections - Source 1, Source 2, Source 3, Source 4, iPod, Source 7, Front Input, Media Player and Tuner (AM/ FM/DAB as applicable). More Sources can be directly recalled upon enabling them at the Setup Menu.
IDENTIFICATION OF CONTROLS REAR PANEL ENGLISH 1 2 3 4 5 6 7 8 9 11 10 12 FRANÇAIS 2 IR OUT IR IN 1 ZONE 2 SURR-B TRIG OUT MP DOCK DATA PORT +12V SWITCHED AC OUTLET COMPONENT VIDEO INPUT 2 COMPONENT VIDEO INPUT 1 COMPONENT VIDEO INPUT 3 MONITOR OUT VIDEO MON. OUT 120V 60Hz 100W 1A MAX S-VIDEO SURR-BACK/ ZONE 2 ESPAÑOL 7.
IDENTIFICATION OF CONTROLS 7 MP DOCK The T 758 is equipped with a data port in the rear panel where an optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later variants can be plugged in. • Connect the MP DOCK (DATA PORT) jack of the T 758 to the corresponding DATA PORT socket of the optional NAD IPD model. • AUDIO 3 and S-VIDEO 1 are the assigned default ports for the audio/ video output of the separately sold NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later variants.
IDENTIFICATION OF CONTROLS REAR PANEL ENGLISH FRANÇAIS 14 AUDIO PRE-OUT • The AUDIO PRE- OUT makes it possible to use the T 758 as a preamplifier to external power amplifiers for some or all channels. Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and SURR-BR to the respective channel input of a power amplifier or amplifiers driving the corresponding applicable speakers. • Unlike the full range channels, there is no power amplifier built-into the T 758 for a subwoofer.
IDENTIFICATION OF CONTROLS ENGLISH AVR 4 REMOTE CONTROL USING THE AVR 4 REMOTE CONTROL 3, 4 7 6 5 8 10 9 11 1 ON, OFF The AVR 4 remote has a separate ON and OFF button. • Press ON button to switch the T 758 from Standby to operating mode. Press OFF button to switch the T 758 to Standby mode. 2 DEVICE SELECTOR A Device Selector button determines only what component the AVR 4 will command; it does not perform any function on the T 758.
IDENTIFICATION OF CONTROLS AVR 4 REMOTE CONTROL ENGLISH 11 VOL 5/6 • Increase or decrease loudness level. Release the button when desired level is reached. • The VFD on the front panel will indicate the level set. For NAD Receivers, the VFD will also show “Volume Up” or “Volume Down” or “Volume: _ _ dB” (_ _ indicates the numerical dB level) while pressing AVR 4’s [VOL 5/6 ] buttons. FRANÇAIS 12 A/S/D/F, ENTER Select an item in a menu.
IDENTIFICATION OF CONTROLS ENGLISH AVR 4 REMOTE CONTROL PORTUGUÊS ESPAÑOL FRANÇAIS TUNER CONTROL (use with T 758 tuner section and other compatible NAD Receiver, AM/FM/ DAB Tuner models) Set the DEVICE SELECTOR to “TUN” in order to gain access to these buttons. Refer to the corresponding labels printed in the remote control faceplate and their respective assigned buttons to make use of these functions.
IDENTIFICATION OF CONTROLS AVR 4 REMOTE CONTROL ENGLISH LIBRARY USING THE ZR 7 REMOTE CONTROL The AVR 4 can store a different library of default NAD codes for each of its DEVICE SELECTOR “pages.” If the original default library does not control your NAD CD player, DVD player, or other component, follow the procedure below to change the library code. Refer as well to the table below for a list applicable NAD Library Codes with their corresponding NAD models.
IDENTIFICATION OF CONTROLS ENGLISH AVR 4 REMOTE CONTROL ALTERNATE IR CHANNEL FRANÇAIS The T 758 has the capability to operate via Alternate IR channel. This is practically useful if you have two NAD products that can be operated by similar remote control commands. With alternate IR Channel, two different NAD products can be controlled independently in the same zone by setting each one to a different IR channel. IR CHANNEL ASSIGNMENT The T 758 and the AVR 4 remote control must be set to the same channel.
OPERATION USING THE T 758 - MAIN MENU ENGLISH ABOUT THE ON-SCREEN DISPLAY (OSD) LISTENING MODE The T 758 employs a simple, self-explanatory system of on-screen display “menus” that will appear on the connected video monitor/TV. These are required during the setup process (and are useful in day-to-day operation), so be sure to connect the monitor/TV before proceeding with the setup.
OPERATION Front (left and right), Center, Surround (left and right), Back Surround (left and right), Subwoofer NEO: 6 Two-channel recordings, whether stereo or surround-encoded, are reproduced with NEO:6 surround with output to front left/right, center and discrete left/right surround channels plus subwoofer (assuming these are present in the current “Speaker Configuration”). The T 758 provides two DTS NEO:6 variations – NEO:6 Cinema and NEO:6 Music.
OPERATION USING THE T 758 - MAIN MENU ENGLISH DSP OPTIONS FRANÇAIS LIP SYNC DELAY DSP Options has the feature “Lip Sync Delay” whose function is to match any delay that may occur in the picture relative to the audio. By varying “Lip Sync Delay” from 0ms to 120ms, one can delay the audio output in order to synchronize it with the video image.
OPERATION To access and navigate through Setup Menu and its sub-menu selections, please refer to and follow the directions stated in the sections ‘Display the OSD’ and ‘Navigating the OSD and Making Changes.’ CONTROL SETUP The T 758 supports HDMI Control (CEC) and Audio Return Channel (ARC) functions. Both functions are possible if external devices that also support both features are interconnected with the T 758 via HDMI connection.
OPERATION USING THE T 758 – SETUP MENU ENGLISH SOURCE SETUP ENABLED One can enable/disable a Source via this option. This is particularly useful if only few Sources are used and one directly selects the Source from the front panel, bypassing unused sources. Select “Yes” to enable the particular Source or “No” to disable the Source. FRANÇAIS There are three sub-menu items under Source Setup. These are Source Setup (Normal View), Source Setup (Table View) and iPod Setup.
OPERATION NOTE An incoming digital signal present at the assigned digital input will always take precedence over the assigned analog audio input, even if both are present. To maintain the analog audio input for the particular Source, select “Off” at the “Digital Audio” setting of the same “Source” menu. Set “Trigger Out” to “On” to enable “Trigger Out” or “Off’ to disable it as per assigned Source.
OPERATION USING THE T 758 – SETUP MENU ENGLISH iPod SETUP AUDYSSEY SETUP It has been shown that many, if not most, surround sound systems are not accurately configured and setup. This requires special knowledge and instrumentation that the average person probably doesn’t possess. FRANÇAIS ESPAÑOL PORTUGUÊS The iPod Setup menu allows you to preset the following associated settings when iPod is the selected source: Enabled: Select “Yes” to enable iPod as a Source or “No” to disable it.
OPERATION It is recommended that you take full advantage of the T 758’s Audyssey Setup feature for your speaker setup. However, if you desire to setup your speakers manually or if you already had run Audyssey Setup but would like to make adjustments, the following sections on Speaker Configuration, Speaker Levels and Speaker Distance can also be followed and implemented.
OPERATION USING THE T 758 – SETUP MENU ENGLISH SPEAKER LEVELS Every surround-sound system requires “bass-management” to direct lowfrequency content from any or all channels to the speakers best able to reproduce it. For this function to operate correctly, it is important that you correctly identify your speakers’ capabilities. We use the terms “Small” and “Large” (and “Off”) but note that physical size may be irrelevant.
OPERATION ADJUSTING THE VOLUME The T 758 will power-up from Standby mode at whatever master volume setting was last used; however, if the prior setting was greater than -20dB, the T 758 will power up at -20dB. This prevents inadvertently beginning a session at excessive volume. MUTING THE SOUND Use the AVR 4’s [MUTE] key to silence all channels completely. Muting is always available regardless of the source or listening mode selections.
OPERATION USING THE T 758 – SETUP MENU ENGLISH LISTENING MODE SETUP If the surround back speakers are not used in the main zone, their surround back amplifier channels could be assigned for Main back, Main Front (BiAmp) and Zone 2 use. The T 758 has various listening mode options and is mostly configurable. These are provided to reproduce a variety of sound effects depending upon the content of the source to be played.
OPERATION It supports bit rates of up to 18 Mbps and records up to 8 full-range channels individually with 24-bit/96 kHz audio. It also features extensive metadata including dialogue normalization and dynamic range control. Supported by High-Definition Media Interface (HDMI), a single-cable digital connection is possible for high-definition audio and video.
OPERATION USING THE T 758 – SETUP MENU ENGLISH DOLBY SETUP DTS SURROUND MODES The following are further descriptions about the DTS surround modes. FRANÇAIS Under this menu, the Dolby Digital’s Dynamic Range Control can be adjusted as well as the settings for Dolby Digital Pro Logic IIx Music. DTS-HD MASTER AUDIO DTS-HD Master Audio is a technology that delivers master audio sources recorded in a professional studio to listeners without any loss of data, preserving audio quality.
OPERATION DISPLAY SETUP ENHANCED STEREO Please refer to the same description of ENHANCED STEREO under the LISTENING MODES segment of the OPERATION - USING THE T 758 - MAIN MENU. ON-SCREEN DISPLAY (OSD) Temp Disp: This applies to the OSD that is temporarily shown at video out whenever any of the front panel controls or their corresponding keys in the remote control is activated. Set to “On” if it is desired to show the applicable OSD at the monitor/TV; otherwise, select “Off”.
OPERATION USING THE T 758 – SETUP MENU ENGLISH A/V PRESETS SAMPLE PROCEDURE FOR SETTING UP A/V PRESETS 1 Setup first your preferred settings for the following options (access them through their respective menu page). Listening Mode: Stereo FRANÇAIS ESPAÑOL The T 758’s simple but powerfully flexible system of “A/V Presets” allows you to customize virtually every aspect of your audio-video playback, and recall them with a single key-press.
OPERATION 3 At “A/V Presets” page, set “Preset: 1” to the following conditions - use [ D/F ] to select “Yes” or “No” and press [ENTER] to confirm selection and move on to the next setting. 2 With the above settings, scroll to “A/V Presets” from the SETUP MENU page. Use [ S ] to access “A/V Presets” menu.
OPERATION USING THE T 758 – SETUP MENU ENGLISH Tone Controls: Tone Defeat: Off 6 At “A/V Presets” page, set “Preset: 2” to the following conditions - use [ D/F ] to select “Yes” or “No” and press [ENTER] to confirm selection and move to the next setting. FRANÇAIS Display Setup: Set “Line 2” to “Volume” ESPAÑOL While at “Save Current Setup to Preset” menu line, use [ S ] to save the settings above to “Preset 2”.
OPERATION The supplied AM “loop” antenna will usually provide adequate reception. However, an exterior AM antenna can be used to improve reception. Consult an antenna professional for more information. IMPORTANT NOTE When using the AVR 4 to carry out AM/FM commands, ensure that the DEVICE SELECTOR is set to “TUN”. ASSEMBLING THE LOOP ANTENNA DELETING A STORED PRESET (AM/FM/DAB) You can empty a preset by deleting the stored information. 1 Select the preset number to be deleted. For example, “P03”.
OPERATION LISTENING TO AM/FM RADIO ENGLISH ABOUT USER NAMES A Preset number can be assigned a twelve “User Name”. The assigned “User Name” will be shown in the VFD and OSD whenever the associated Preset number is recalled. FRANÇAIS ESPAÑOL ENTERING USER NAMES A Preset number can be assigned the user name “NEWS” by the following procedure. The buttons mentioned below refer to AVR 4 buttons. The corresponding front panel buttons execute the same functions as described.
OPERATION FRANÇAIS ESPAÑOL PORTUGUÊS 2 To tune to DAB broadcast services, press [TUNER MODE] and then toggle [ A/S ] to select either “Full Scan” or “Local Scan”. FULL SCAN will enable the scanning of the full range of digital frequencies (Band III and L-Band). LOCAL SCAN performs local scanning of available DAB services in your area. Check with your dealer or visit www.WorldDAB.org to check the applicable digital transmission frequencies in your area.
OPERATION LISTENING TO DAB RADIO ENGLISH 4 Press and hold [ENTER] button to check the strength of the incoming signal. The more segments visible in the lower display line, the stronger the signal. By changing the position of the antenna, you can increase the signal strength. You can also opt for an external antenna. Consult an antenna professional for more information.
OPERATION RESET INFORMATION SETTINGS The “Reset” option allows the connected (and separately sold) NAD DAB Adaptor to be reset to its factory default settings. 1 While listening to a DAB broadcast, press [TUNER MODE] button and [ A/S ] to select “Reset”. 2 Press [ENTER]. “Reset? No” will be shown in the lower line of the VFD. Press [ A/S ] to switch to “Reset? Yes” option. While listening to a DAB broadcast, the type of information displayed in the lower line of the VFD can be varied.
OPERATION LISTENING TO YOUR iPod PLAYER ENGLISH The T 758 is equipped with a data port in the rear panel where an optional “NAD IPD Dock for iPod” (NAD IPD) can be plugged in. With the NAD IPD linking the T 758 with your own iPod player, you can enjoy listening to your favorite tracks and playlists as well as view applicable still image and video playback. FRANÇAIS You can control your iPod player using the assigned buttons in the T 758 front panel.
OPERATION REGAIN CONTROL OF NAD IPD 2 USING DR 1 REMOTE CONTROL In order to switch back control of the NAD IPD 2 from the T 758/AVR 4 to the DR 1 remote control, follow these steps. 1 Exit from the iPod Menu by pressing repeatedly [ A ] until it brings you to “Menu Select” OSD. 2 Highlight “iPod Menu” and press [ S ] to advance to “iPod Menu”. 3 At “iPod Menu”, press [ S ] to close iPod menu. DR 1 remote control regains control of the NAD IPD 2.
REFERENCE TROUBLESHOOTING ENGLISH CONDITION No sound from all channels. POSSIBLE CAUSES • AC power unplugged. POSSIBLE SOLUTIONS • Check AC cable connection and outlet. • Power not switched on. • Outlet has no power. FRANÇAIS No sound from some channels. No sound from surround channels. • Mute function is activated. • Toggle [MUTE] button to deactivate Mute function. • Faulty/missing cables. • Check cables. • “Speaker Configuration” channel (s) set to “OFF”. • Check “Speaker Configuration” menu.
REFERENCE 110W (8 ohms within rated distortion) IHF dynamic power; 8 ohms 137W IHF dynamic power; 4 ohms 243W Power output Surround Mode 7 x 60W Total harmonic distortion at rated power <0.08% IM distortion at rated power <0.08% Damping factor, 8 ohms >60 Input sensitivity and impedance 750mV/50 kilo ohms Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest information about T 758.
www.NADelectronics.com ©2015 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
