Operation Manual

LIBRARY
The AVR 3 can store or assign a dierent NAD code library for a particular DEVICE. If the original default
library does not control your NAD CD player, DVD player, or other component, follow the procedure below
to change the library code. Note that there maybe some remote control functions or buttons specic for a
particular NAD model not available when a particular library code is stored in a device. Refer as well to the
table below for a list applicable NAD Library Codes with their corresponding NAD models.
LOAD ANOTHER LIBRARY CODE
Example: Load NAD DVD Player T 517 library codes to AVR 3’s “BD” device.
1 Press and hold [BD] in the DEVICE SELECTOR section of AVR 3.
2 While holding down the device button [BD], press “2” and “2” using AVR 3’s numeric buttons. “22” is
the corresponding library code for T 517.
3 Press [ENTER] while still holding down the device button [BD]. The BD device selector will ash
once to indicate that the library input is successful. Both the device selector button [BD] and
[ENTER] can now be released.
RESET THE AVR 3 TO ITS DEFAULT SETTINGS
The AVR 3 can be restored to its factory settings, including default libraries, by the following
procedures
1 Press and hold [ON] and [DELETE] buttons for about 10 seconds until the AMP device button lights up.
2 Within two seconds of the AMP device button lighting up, release both buttons. If the reset mode
is successful, the [BD] device button will ash twice.
TABLE OF LIBRARY CODES APPLICABLE TO AVR 3 REMOTE CONTROL
LIBRARY CODE NAD PRODUCT DESCRIPTION
10 Default library for ‘AMP” page
11 Zone 2
20 C 515BEE, C 545BEE, C 565BEE
21 T 535, T 585, M55; DVD section of L 54, VISO TWO, VISO FIVE
22 T 513, T 514, T 515, T 517
23 Default library for “BD” page; T 587, T 557, T 577, M56
30 IPD 1
31 IPD 2
40 Default library for “TUN” page; Tuner section of C 725BEE, T 175, T737, T 755, T 765, T 775, T 785
41 C 422, C 425
42 C 445
NOTE
The AVR 3 may not necessarily contain all the control buttons applicable for the above-mentioned
NAD products. Use the prescribed remote control of the specic NAD product for a full compliment
of the applicable remote control buttons
USING THE ZR 5 REMOTE CONTROL
The ZR 5 is a discrete compact remote for controlling the applicable Zone 2 features of the T 747.
Irrespective of the main room/zone settings, the ZR 5 allows full separate control of the Zone 2 source
selection among other applicable features.
1 ON/OFF: Switch ON/OFF the Zone feature.
2 SOURCE [ ]: Select the active input of the NAD T 747 that will be sent out to the
corresponding rear panel ZONE 2 output port.
3 MUTE: Temporarily switch OFF or restore the Zone Volume level.
4 VOL [ ]: Increase or decrease the loudness level of selected Zone source. This is possible only
if the VOLUME setting of ZONE 2 CONTROLS is set to VARIABLE.
5 PRESET [ ]: Step up or down between stored radio presets. This control button is possible if
the selected Zone is “TUNER” and the active tuner section has stored presets.
6 The following CD Player Zone buttons can control a compatible CD Player. The CD Player has to be
powered ON and disc loaded.
SKIP [ ] : Go to the beginning of a track/le or previous track/le.
SKIP [ ]: Go to the next track/le.
[ ]: Start playback.
IDENTIFICATION OF CONTROLS
REMOTE CONTROL
1
3
4
6
2
5
14
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ