Operation Manual
The T 747’s internal AM/FM tuner oers very high quality sound from radio
broadcasts. The reception and sound quality will always be dependent to a
degree however on the type of antenna(s) used as well as proximity to the
broadcast origin, geography and weather conditions.
ABOUT ANTENNAS
Connect the supplied lead-type FM antenna to the FM antenna input. Extend
the lead. Experiment freely with your antenna placement and orientation until
you get the clearest sound and lowest background noise. Fix the antenna in
the desired position by using thumb tacks, push pins or any suitable means. In
areas of poor FM reception, an exterior FM antenna can improve performance
dramatically. If radio listening is important to you, consider consulting an
antenna installation professional to optimize your system.
The AM loop antenna supplied with the T 747 (or a suitable replacement)
is required for AM reception. Open the clip terminal lever; insert the wire
making sure to match the color-coded (white and black) ends of the
wire to that of the terminal and close the lever ensuring that the lever
locks the wire in place. Testing dierent positions for the antenna may
improve reception; vertical orientation will usually produce the best results.
Antenna proximity to large metal objects (appliances, radiators) may impair
reception, as will attempts to lengthen the wire to the loop.
The supplied AM “loop” antenna will usually provide adequate reception.
However, an exterior AM antenna can be used to improve reception.
Consult an antenna professional for more information.
IMPORTANT NOTICE
Unless otherwise specically stated, navigating or accessing AM/FM
functions can be undertaken by using either the AVR 3 remote control
or the front panel buttons. If the control button or icon button being
referred to is available on the AVR 3 remote control and front panel,
then the reference to said button is applicable to both the AVR 3 remote
control and front panel.
NOTE
When using the AVR 3 remote control to carry out AM/FM commands,
ensure that the DEVICE SELECTOR is set to “TUN”.
ASSEMBLING THE LOOP ANTENNA
1 Rotate the outer frame of the antenna.
2 Insert the bottom edge of the outer frame into the groove on the stand.
3 Extend the antenna cord.
SELECTING A TUNER BAND
Press the [AM/FM/DB] button on the AVR 3 while at AMP or TUNER device
selector page. Each subsequent press of either button will toggle you
through AM, FM and XM (or DAB) band. Stop (release button) at your
desired tuner band.
TUNING AM/FM STATIONS
Upon selecting AM or FM band, use [TUNE ] on the AVR 3 to
perform slow manual search; press and hold to automatically search.
The front panel or AVR 3’s [ ] buttons can also be used to tune for
stations.
1 Press [ ] momentarily to step up or down between AM or FM
frequencies.
2 Press and hold [ ] for more than 2 seconds to search up or down
- the T 747’s tuner will stop at the next suciently strong signal it
encounters.
3 Pressing the [ ] during the search process will stop the search.
DIRECT TUNING
If you know your desired station’s frequency allocation, you can tune
directly to the station.
1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see
the lower line of the VFD). Select “Tune” mode.
2 Using the numeric keys of the remote control, key-in the frequency
allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,
“4”, “5” and “0” or press “”1”, “0”, “4” and “5”.
SETTING RADIO PRESETS AM/FM
The T 747 can store up to 30 FM and 30 AM stations for immediate recall.
1 To store a radio preset, rst tune the desired frequency (see above), then
press AVR 3’s [MEMORY] key.
2 The VFD will show the next available Preset number (If there are no more
vacant Preset number, you can overwrite an existing Preset number
by pressing the [ ] buttons to select the Preset number you want
to overwrite). Press the [MEMORY] button again to store the desired
frequency on the Preset number shown (or use the [ ] buttons to
select another available Preset number and then, press [MEMORY] button
again). Your desired frequency is now stored in the assigned preset.
Press [ ] to step up or down between presets. Press and hold [ ]
to “scroll” continuously up or down. The AVR 3 remote’s [PRESET ]
keys work similarly.
OPERATION
LISTENING TO AM/FM RADIO
32
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ