Owner`s manual
DIGITAL AUDIO
To take advantage of the T 777’s high performance surround and digital
audio circuitry, it is advisable that its sets of Digital Audio input are selected.
There are three types of Digital Audio input for the T 777. These are HDMI,
Optical and Coaxial digital input. A fourth option is “O” whereby no
incoming digital audio signal is selected by the particular Source.
The desired digital audio input for a particular Source can be selected by
scrolling to “Digital Audio”, press [S] and then [D/F] to step through the
desired digital input source. After nalizing the desired type of Digital Audio
input, press [S] and then [D/F] again to select the specic Digital Audio
input.
The following are the sets of assignable Digital Audio input:
HDMI $ HDMI 1 - 6, HDMI Front
Optical $ Optical 1 - 3
Coaxial $ Coaxial 1 – 3
NOTE
An incoming digital signal present at the assigned digital input will
always take precedence over the assigned analog audio input, even if
both are present. To maintain the analog audio input for the particular
Source, select “O” at the “Digital Audio” setting of the same “Source”
menu.
VIDEO
There are four types of video input a particular Source could be assigned.
These are HDMI, Component, S-Video and Video input. Another option is
“O”. Select “O” if it is intended not to assign any video input to a particular
Source.
Navigate through the Video input selections by pressing [S] and then
[D/F] to step through the selections. The following are the sets of
assignable Video input.
HDMI $ HDMI 1 - 6, HDMI Front
Component Video $ Component 1 - 3
S-Video $ S-Video 1 - 3, S-Video Front
Video $ Video 1 - 3, Video Front
IMPORTANT NOTE ABOUT THE VIDEO PERFORMANCE OF T 777
The T 777 utilizes an NAD-engineered eld-programmable gate array
(FPGA) that is capable of enabling the conversion of analog video to
digital video. This allows a single cable connection to your TV for all
sources while maintaining the source’s native resolution. Interlaced
video is converted to progressive scan over HDMI allowing complete
compatibility with latest HD TVs.
The T 777 also supports HDMI features that include compatibility with a
broad range of 3D and HD digital video sources and displays.
A/V PRESET
A particular Source can be assigned a stored Preset. The parameters set up
in the selected Preset number will be adopted into the particular Source it
is assigned (Please refer to the separate section on “A/V Presets” for further
understanding of Preset settings).
Scrolling to “A/V Preset” and by pressing [S] and then [D/F], a Source could
be assigned a Preset number ranging from Preset 1 to 5.
If it is desired not to assign the particular Source a Preset setting, select
“None”.
TRIGGER OUT
Trigger Out feature for a particular Source is dependent upon the
congurations done in a separate menu on Trigger Setup (See “Trigger
Setup” below). If “Source Setup” is assigned to all three Trigger output
(Trigger Out 1-3) in the separate “Trigger Setup” menu window, a particular
Source can have the following Trigger Out combinations
Trigger Out: 1 $ 2 $ 1 + 2 $ 3 $ 1 + 3 $ 2 + 3 $ 1+2+ 3
These combinations are dependent upon the assignment of “Source Setup”
for Trigger 1 Out, Trigger 2 Out or Trigger 3 Out at the “Trigger Setup” menu.
Another option is “None” whereby the particular Source is not assigned any
Trigger Out.
For “Trigger Out” to become enabled and assignable at “Source Setup
(Normal View)” menu, make sure to carry out or note the following
beforehand
• In the separate “Trigger Setup” menu, assign Trigger 1 Out, Trigger 2 Out
or Trigger 3 Out to “Source Setup.”
• “Trigger Out” will not appear as an option at the Source Setup (Normal
View) menu if at the separate “Trigger Setup” menu, Trigger 1 Out,
Trigger 2 Out or Trigger 3 Out are all assigned to “Main, Zone 2, Zone 3,
Zone 4, or Zone 2+3+4”; with not even one “Trigger Out” port allocated
to “Source Setup.”
SOURCE SETUP (TABLE VIEW)
The Source Setup (Table View) reects the settings made in the Source
Setup (Normal View) menu. All the Source settings are summarized and
displayed in tabulated form in the Source Setup (Table View).
Navigating through the Source Setup (Table View) via a combination
of [A/S] and then [D/F] buttons, one will have the benet of directly
changing the settings for “Audio”, “Video”, “Preset” and “Name” without
going back to the Source Setup (Normal View) menu.
Highlight a particular Source number and then, toggle [ENTER] button
to enable or disable said Source number.
OPERATION
USING THE T 777 SETUP MENU
18
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ