Operation Manual

1 SPEAKERS: Connect the left and right terminals to the corresponding
loudspeakers. Each output’s “+” (red) terminal and “-” (black) terminal
must be connected to the corresponding “+” and “-” terminals of the
loudspeaker. Use extra care to ensure that no stray wires or strands cross
between posts or terminals at either end.
NOTES
• Usestrandedwireofatleast16-gauge(AWG);specializedspeakercable
maybevaluable(consultyourNADaudiospecialist).Connectionsto
theVISOTWOcanbemadewithbanana-typeplugs,orusingbarewire,
orpins,bylooseningtheterminal’splasticnut,makingaclean,neat
connection,andre-tighteningcarefully(usethetransverseholethrough
thepostforbare-wireorpinconnections).Tominimizethedanger
ofshort-circuits,ensurethatonly1/2-inchofexposedwireorpinis
employedinconnecting.
• Thisunitisdesignedtoproduceoptimumsoundqualitywhenconnectedto
speakerswithimpedanceswithinthereceiver’soperatingrange.Pleasecheck
that speakers are rated to be 8 ohms minimum per speaker.
2 FM ANTENNA INPUT: The supplied wire “dipole” FM antenna will
connect to the FM connector using the supplied “balun” adapter. It will
usually work best when mounted on a vertical surface such as a wall,
with arms fully outstretched forming a horizontal “T” perpendicular to
the origin point of the signal.
3 AM ANTENNA INPUT: Connect the supplied AM loop antenna to
these terminals. If an external AM antenna is used, make connections to
the AM and GND terminals in accordance with the instructions supplied
with the antenna. See also section about “LISTENING TO AM/FM RADIO”.
4 CABLE/SAT & VCR: Connect to these inputs S-Video, composite
video, and analog audio from source components such as cable TV
decoders, satellite tuners, another DVD player or other applicable
ancillary devices. VCR may be used with recording components such
as videocassette or DVD-recorders. Connect the VCR OUT (audio/video)
to these components’ corresponding audio/video input. Note that VCR
may freely be used for play-only components, in which case their OUT
jacks would remain unconnected.
5 SUBW (SUBWOOFER) PRE OUT: Connect this output to a powered
(active) subwoofer or to a power amplier channel driving a passive system.
6 DAB MODULE INPUT (Europe version only): Plug-in the other end
of the Mini-Din connector from the NAD DAB Adaptor DB 1 module
output port into this socket. The VISO TWO is compatible only with
NAD DAB Adaptor DB 1 so check with your NAD dealer for this module’s
availability. With DAB, you can receive CD-like quality programs without
any annoying interference and signal distortion.
7 MP DOCK: The VISO TWO is equipped with a data port in the rear
panel where an optional “NAD IPD 1 Dock with iPod” (NAD IPD 1) can be
plugged in. Connect the “MP DOCK (DATA PORT)” jack of the VISO TWO
to the corresponding “DATA PORT” socket of the optional NAD IPD 1.
8 COAXIAL IN, OPTICAL IN: Connect to the optical or coaxial S/PDIF-
format digital output of sources such as CD or DVD players, HDTV or
satellite tuners and other components.
IDENTIFICATION OF CONTROLS
REAR PANEL
ATTENTION!
 PleasemakesurethattheVISOTWOispoweredoorunpluggedbeforemakinganyconnections.Itisalsoadvisabletopower-downorunplugall
associatedcomponentswhilemakingorbreakinganysignalorACpowerconnections.
1 4 5 6 7 8 9 10 11 12
15 18 19
2 3
16 17 20
13 14
European version only
European version only
European version only
North American
version only
North American
version only
10
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ