User Manual

ManualsBrandsNADAMOO ManualsBar Code ScannersWireless Barcode Scanner with Stand 2-in-1 2.4G Wireless & Wired USB Bar Code Scanner Handheld Laser Bar Code Reader Automatic Hand Scanner for Computer POS Warehouse Inventory Library

Table Of Contents

Bur3074 NADAMOO 2.4G Wireless & USB wired Barcode Scanner

Quick Start Guide

In order to correctly use the bar code scanner, please read the instruction

carefully and do not arbitrarily scan the settings code, otherwise some

settings may not be available.

Please keep this instruction for reference in the future.

If you have any question or concern about the operation of the scanner,

please contact us at Email: server@nadamoo.cn / burnfree@126.com.

Package Include

1 x Bar code scanner

1 x USB cable

1 x USB Wireless receiver

1 x User manual

Charging

Please ensure that the scanner has enough power. If the scanner runs out of

power, the buzzer will ring for seconds, and the scanner will shut down

automatically. At this case, please stop scanning and recharge the scanner.

Please insert one end of USB cable into the scanner correctly, and insert

another end to computer USB interface or 5V DC USB interface power (NOTE:

please use computer USB interface or special 5V DC power supply to charge, the

abnormal power will cause permanent damage to scanning gun and battery).

Yellow LED light will light up when the scanner is at charge statue. It will take

about 4 hours to recharge the scanner. After full charged, the LED light will go

out automatically.

Connection Setting

This scanner has two connection mode:

Mode 1: Wired Mode.

Set by steps

：

1. Connect the scanner to your computer via USB cable;

2. Scan the code " PS2 keyboard wired mode " to convert the scanner to wired mode.

PS2 keyboard wired mode

Summary of content (22 pages)

PAGE 1
Bur3074 NADAMOO 2.4G Wireless & USB wired Barcode Scanner Quick Start Guide In order to correctly use the bar code scanner, please read the instruction carefully and do not arbitrarily scan the settings code, otherwise some settings may not be available. Please keep this instruction for reference in the future. If you have any question or concern about the operation of the scanner, please contact us at Email: server@nadamoo.cn / burnfree@126.com.
PAGE 2
3. Test the scanner using Microsoft EXCEL, click any cell and scan a product bar code, the code will automatically appear in the cell. In wired mode, user can set up the speed of uploading data. ** Scan one of the following bar code to select the speed mode for uploading. Upload speed-fast Upload speed-modest(default) Upload speed-slow Mode 2: Wireless Mode Set up steps: 1. Plug the USB wireless receiver into a PC’s USB port; 2.
PAGE 3
**To convert from "instant upload mode" the following barcode. to "Collection upload mode", please scan Collection upload mode ** Scan the following barcode to upload the stored data. Upload data **Scan the following barcode to show total number of stored barcode Show total storage **Scan the following barcode to clear all the stored barcode. Clear data Customer FAQ Q1.
PAGE 4
Q2. Why can’t the scanner read the bar codes? There may be several reasons for this issue. 1) It may be due to setup errors. If you want to use it in wired mode, please connect the scanner to your computer via usb cable and scan the code " PS2 keyboard wired mode". PS2 keyboard wired mode If you want to use it in wireless mode, please connect the scanner to you computer via USB receiver, and then scan the following codes "Match the receiver" "Wireless mode" "instant upload mode".
PAGE 5
Scanning Mode Setting Key trigger mode: Red laser light only show up when you press the button. Continuous scanning mode: Red laser light always on when the scanner is electrified. The scanner reads barcode without pressing any buttons. ** Scan one of the following barcode to select scanning mode. Keys Trigger mode (default) Continuous Mod Buzzer settings： * * Scan one of the following barcode to ON / OFF the buzzer.
PAGE 6
Insert charater as prefix (1) Step 1: scan the set up code (Add prefix) below： Add prefix (2) Step 2: scan the needed character code (character-table E.g. To add prefix " RST", scan the character R , S ,T one by one. 1082 R Now the "RST" 1083 is on page 15) S 1084 T will be added, then scan the normal bar code. (3) Step 3: Scan your goal barcode, e.g. scan the below code "X001E52257", the bar code "RSTX001E52257" will be showed.
PAGE 7
(3) Step 3: Scan your goal barcode, e.g. scan the below code "X001E52257", the barcode "X001E52257RST" will appear. X001E52257 Clear Prefix / suffix character Clear all character prefix Clear all character suffix Terminator setting： Before add/ change any Terminator, scan the following code "Disable Format character " at first, then to scan corresponded code.
PAGE 8
Hide characters from start position of Code Shorten the barcode from start position as followed: (1) Step 1: scan the set up code "Hide chacaters from start position" below： Hide characters from start position (2) Step 2: scan one of the following code to set how many characters you want to hide, e.g. Code "1050 2" means the starting 2 characters in the barcode that you scanned will be hidden.
PAGE 9
Hide characters from end part of Code Shorten the bar code from end part as following steps showed: (1) Step 1: scan the set up code "Hide characters from end position" below： Hide characters from end position (2) Step 2: scan one of the following code to set how many characters you want to hide, e.g. Code "1050 2" means the ending 2 characters in the barcode that you scanned will be hidden.
PAGE 10
Hide characters from specific part Hide a partial of the barcode from specific place in the middle of the barcode. Following the steps to set up: (1) Step 1: scan the set up code "Hide characters from m" below： Hide characters from m (2) Step 2: scan one of the following code to decide from which character you want to hide ("m" means the beginning place of the character) , e.g. Code "1050 5" means from 5th character in the barcode that you scanned will begin to be hidden.
PAGE 11
1049 1 1050 2 1051 3 1052 4 1053 5 1054 6 1055 7 1056 8 1057 9 Example: For barcode 123456789, if you want to limit the result characters to 126789 ("345" in the barcode is hidden), you can scan these codes one by one, any wrong scanning order will result in failure setting: "Hide characters from m" --- "1051 2"--- "Hide middle n characters"--- "1051 3" Hide characters from m Hide middle n characters 1050 2 1051 3 * scan the code below to reinstate the hidden middle character cancel shorten m
PAGE 12
Identify Barcode type This setting is to identify what type of the barcode is, follow the below steps to confirm: Situation 1: Scan the code "Add Code ID as prefix" below, then scan your goal barcode, there will be a character BEFORE the barcode you scanned, and this character states your Barcode Type. After that, if you don't need this prefix any more, please scan the code "Turn off ID (default)" to hide it.
PAGE 13
Barcode setting When scanning the code ending with word "On" means the this type of code / function is available, while scanning the code ending with word "Off" means this type of code / function is disable.
PAGE 14
EAN13-On EAN13 to IBSN- On EAN13-Off EAN8-Off EAN8-2digit EAN8-5 digit Code93-On Code93-Off Code128-On Codabar-On EAN13-check EAN8-check digit- On EAN8-chec digit-Off EAN13 to IBSN- Off EAN8 -On extracode-On EAN13-check digit -On digit-Off EAN8- extracode-Off extracode-On Code128-Off Codabar-Off Codebar start/end digit-on 14 Codebar start /end digit-off
PAGE 15
Interleaved 2 of Interleaved 2 of Industrial 2 of 5 Industrial 2 of MSI -On MSI-Off Code11-On Code11-Off 5-On -On 5-Off 5-Off Character-table 1001 SOH 1002 STX 1003 ETX 1004 EOT 1005 ENQ 1006 ACK 1007 BEL 1008 Backspace 1009 TAB 15
PAGE 16
1010 LF 1011 VT 1012 FF 1013 CR 1014 SO 1015 SI 1016 DLE 1017 DC1 1018DC2 1019 DC3 1020 DC4 1021 NAK 1022 SYN 1023 ETB 1024 CAN 1025 EM 1026 SUB 1027 ESC 1028 FS 1029 GS 1030 RS 1031 US 1032 SPACE 1033 ! 1034 " 1035 # 1036 $ 16
PAGE 17
1037 % 1038 & 1039 ‘ 1040 ( 1041 ) 1042 * 1043 + 1044 , 1045 - 1046 .
PAGE 18
1064 @ 1065 A 1066 B 1067 C 1068 D 1069 E 1070 F 1071 G 1072 H 1073 I 1074 J 1075 K 1076 L 1077 M 1078 N 1079 O 1080 P 1081 Q 1082 R 1083 S 1084 T 1085 U 1086 V 1087 W 18
PAGE 19
1088 X 1089 Y 1090 Z 1091 [ 1092 \ 1093 ] 1094 ^ 1095 _ 1096 ` 1097 a 1098 b 1099 c 1100 d 1101 e 1102 f 1103 g 1104 h 1105 i 1106 j 1107 k 1108 l 1109 m 1110 n 1111 o 19
PAGE 20
1112 p 1113 q 1114 r 1115 s 1116 t 1117 u 1118 v 1119 w 1120 x 1121 y 1122 z 1123 { 1124 | 1125 } 1126 ~ 1127 Delete 1128 F1 1129 F2 1130 F3 1131 F4 1132 F5 1133 F6 1134 F7 1135 F8 1136 F9 1137 F10 1138 F11 20
PAGE 21
1139 F12 1140 INSERT 1141 HOME 1142 Page up 1143 Delete 1144 END 1145 Page down 1146 Right arrow 1147 Left arrow 1148 Down arrow 1149 Up arrow Power off The system default standby time is 30s. If non-operation in 30s, the scanner will issue a long beeping and shut down automatically. Scan the following code to set standby time.
PAGE 22
Reset the factory default setting If you do not need the previously configured functions, please reset the scanner to the factory settings by scanning the following code. reset the factory default NOTE: After resetting the scanner, you need to choose the connection mode again. Operation steps see above in Page 1 Technical Parameters Interface：USB Wires + 2.