Bluetooth barcode scanner Quick Start Guide Package Include: 1x Handheld barcode scanner 1x USB receiver 1x USB Cable Decoder parameters: Working current：3.5 V ± 10%x100mA Light source：632nm Visible red light Sensor：Linear CCD Sensor, Resolution：2500 CPU：ARM 32-bit Cortex, Decoding speed：300/sec Decoding accuracy：≥3.
Storage：512KB=5000 EAN13 barcodes Working time：Full load≈18hours,Normal use ≈3 to 10days Compatible system: Windows series, Mac、Android、IOS Connection: Bluetooth connection, Wired connection Wireless type：Bluetooth, Distance：≤10m/33ft Shape description Dimensions：120X48x23mm Charge LED： During charging, the green light is on. When the green light is off, the charging is completed Decoder LED： Press button to start the scanner, the green light is on.
Connection Mode Setting I.Wired Mode: 1. Connect the scanner to your computer Via USB cable 2. Press the scanner's blue button to start the scanner. 3. Scan the following code to convert the scanner to wired mode Wired Mode 4.Run Microsoft Word or notepad on computer,put the cursor in the field. when barcode is scaned, the scanner inputs the barcode into the location of the cursor. II.Bluetooth Mode: Bluetooth Mode Match Note: 1.Be sure the scanner is set to Bluetooth Mode. 2.
2.Read "Bluetooth mode" barcode to convert scanner to bluetooth mode 3.Read "Match" barcode, blue light flashing which means in matching mode. 4.Turn on the Bluetooth in Android / IOS device, search for "General Bluetooth HID Barcode" 5. Click "General Bluetooth HID Barcode" in available device, when the connection is successful, the blue light is a normally on and the buzzer drops twice. Pairing with Windows 8/10 1, Insert the Bluetooth USB receiver, the computer will automatically install the drive.
6, Double-click the device, the computer will automatically install the driver ,When the connection is successful, the blue light is a normally on and the buzzer drops twice. Pairing with Windows XP 1, Insert the Bluetooth receiver, the computer will automatically install the drive. 2, Press the button, the buzzer sounds twice, the green light is on and the scanner starts.
supports up to 5000 barcodes .You could upload the data to computer when you need it. An operation in storage mode is strongly recommended under the following scenarios: 1) During the scanning process, the device often leaves the Bluetooth signal range; 2) Due to a high quantity of blocking objects, the Bluetooth signal’s stability can’t be ensured.
** Scan the following barcode to set the scanner to key trigger mode Keys Trigger mode (default) ** Scan the following barcode to set the scanner to continuous mode Continuous Mode ** Scan the following codes orderly to set the scanner to Auto -induction mode Enter into Auto -induction setting Auto-induction mode --ON **Scan the following code to turn off Auto-induction mode Auto-induction mode--OFF 7
Profile Setting 1.HID profile (frequently-used) In the HID protocol, there are 2 entities: the "host" and the "device". The host communicates with the device and receives input data from the device on actions performed by the human. The most common example of a "host" is a PC but some cell phones also can be hosts. The "device" is the entity that directly interacts with a human, such as a keyboard or mouse.
Usage Scenarios: A scenario would be using two devices, such as PCs or laptops, as virtual serial ports and then connecting the two devices via Bluetooth technology.
Character Setting 1.Insert Custom prefix (1) First step,scan the following code “Enter custom prefix setting” Enter custom prefix setting (2)Second step: scan the needed character code (char-table is on page 19-25) E.g. To add prefix ”VC”,scan the corresponding character code 1086 ,1067 in order. 1086 V 1067 C (3) Third step : scan the following code“ Exit custom prefix setting” Exit custom prefix setting After that, when you scan a barcode X001E52257, “VCX001E52257” will show. X001E52257 2.
3. Insert Custom Suffix (1) First step,scan the following code “Enter custom suffix setting” Enter custom suffix setting (2)Second step: scan the needed character code (char-table is on page 19-25) E.g. To add prefix ”VC”,scan the corresponding character code 1086 ,1067 in order. 1086 V 1067 C (3) Third step : scan the following code“ Exit custom prefix setting” Exit custom suffix setting After that, when you scan a barcode X001E52257, “X001E52257VC” will show. X001E52257 4.
5. hide prefix character Scan one of the following bar codes to hide the corresponding prefix characters. Hide 1 prefix character Hide 2 prefix character Hide 3 prefix character Hide 5 prefix character E.g. For barcode 123456, if you set the scaner to hide 1 prefix character. The data received by the host is "23456" 6. Unhide prefix character Scan the barcode below to unhide prefix characters. Unhide prefix character 7.
hide 5 suffix character hide 3 suffix character E.g. For barcode 123456, if you set the scaner to hide 1 suffix character. The data received by the host is "12345" 8. Unhide suffix character Scan the barcode below to unhide suffix characters. Unhide suffix character 9.
hide from the fifth character hide from the sixth character hide from the seventh character hide from the eighth character Second step, scan one of the following bar codes to set the scanenr to hideN-bit characters.
E.g. For barcode 123456789, If you want to set the scanner to hide the "56" character First,scan the programming code “hide from the fourth character” Second,scan the programming code “Hide two character” After that, the data received by the host is "1234789" 10.
Language settings Scan one of the following codes to set the language UNITED STATES ITALY GERMANY RUSSIAN Finland FRANCE Voice Settings Scan one of the following codes to set the voice Open Decoding Voice (default) Close Decoding Voice High volume low volume 16
Sleep Time Setting The scanner will start sleep mode if there is no operation on it over 30s. Short press on the trigger can wake it up. Here is the steps to change the sleeping time： First：scan code"into sleep time setting". Into sleep time setting Second：Scan one of the following barcode to set the time interval, when it's idle exceeding the time interval you set,the scanner will power off.
Restore Factory Setting If you do not need the previously configured functions,scan the code”Restore defaults”to restore the scanner Restore defaults Buzzer & FAQ Buzzer： 1, Long beeps once：Bluetooth disconnected 2 ,Long beeps twice：Bluetooth module failure 3, Long beeps 3 times：Low battery,Please charge 4, Short beeps once： upload OK,Settings OK 5, Short beeps twice：connection succeeded 6, Short beeps 3 times：upload failed 7 ,Short beeps 5 times：Setting error, matching error FAQ: 1.
Character table 1001 SOH（01） 1002 STX（02） 1003 ETX（03） 1004 EOT（04） 1005 ENQ（05） 1006 ACK（06） 1007 BEL（07） 1008 Backspace（08） 1009 HT （09） 1010 LF（0A） 1011 VT（0B） 1012 FF（0C） 1013 CR（0D） 1014 SO（0E） 1015 SI（0F） 1016 DEL（10） 1017 DC1（11） 1018 DC2（12） 19
1019 DC3（13） 1020 DC4（14） 1021 NAK（15） 1022 SYN（16） 1023 ETB（17） 1024 CAN（18） 1025 EM（19） 1026 SUB（1A） 1027 ESC（1B） 1028 FS（1C） 1029 GS（1D） 1030 RS（1E） 1031 US（1F） 1032 Space（20） 1033 ! 1034 “ 1035 # 1036 $ 1037 % 1038 & 1039 ‘ 20
1040 ( 1041 ) 1042 * 1043 + 1044 , 1045 - 1046 .
1061 = 1062 > 1063 ? 1064 @ 1065 A 1066 B 1067 C 1068 D 1069 E 1070 F 1071 G 1072 H 1073 I 1074 J 1075 K 1076 L 1077 M 1078 N 1079 O 1080 P 1081 Q 22
1082 R 1083 S 1084 T 1085 U 1086 V 1087 W 1088 X 1089 Y 1090 Z 1091 [ 1092 \ 1093 ] 1094 ^ 1095 _ 1096 ` 1097 a 1098 b 1099 c 1100 d 1101 e 1102 f 23
1103 g 1104 h 1105 i 1106 j 107 k 1108 l 1109 m 1110 n 1111 o 1112 p 1113 q 1114 r 1115 s 1116 t 1117 u 1118 v 1119 w 1120 x 24
1121 y 1122 z 1123 { 1124 | 1125 } 1126 ~ 1127 Delete 25
