WORLD CLASS HI-FI OWNERS MANUAL Preamplifiers, Integrated Amplifier, Power Amplifiers, Power Supplies
Contents IMPORTANT Page Section In order to comply with current European safety regulations it is essential that the Naim loudspeaker connectors supplied with amplifiers and loudspeakers are used. 1 Do not under any circumstances allow anyone to modify your Naim equipment without first checking with the factory, your dealer, or your distributor. Unauthorised modifications will invalidate your guarantee.
Introduction Naim Audio products are conceived with performance as the top priority. Careful installation will help ensure that their full potential is achieved. This manual covers all Preamplifiers, the Nait 5i Integrated Amplifier, all Power Amplifiers and all Power Supplies but begins with general installation notes and statutory safety warnings for all Naim Audio products. Product specific information begins in Section 5.
Introduction 4 General Installation Naim equipment is designed to offer the finest sound quality possible avoiding compromise wherever practical. This can lead to circumstances that may be unfamiliar. The notes that follow contain advice specifically related to Naim equipment as well as more general warnings about the use of domestic audio products. Please read them carefully. 4.
Preamplifier NAC 552 5 Installation and Operation The NAC 552 preamplifier does not incorporate an internal power supply and can be used only in conjunction with the NAC 552PS power supply. Diagram 6.3 illustrates connection of the NAC 552 to its power supply. The four transit screws on the underside of the NAC 552 case should be removed before use and must be replaced if the unit is to be re-packed and shipped. These transit screws must not be used in any other Naim product.
NAC 552 The remote handset mono (Flash) or mon (Narcom 3) key can also be used to set up automatic source switching. Automatic input switching only becomes operational on exiting from program mode by pressing and holding the handset prog key. Note: In a few cases some further equipment configuration may be required for auto switching to operate correctly on the AV input. Please contact your retailer or local distributor for advice. 5.
Preamplifier NAC 552 6.2 NAC 552 Rear in 1 in 2 Inputs 1, 2 & 3 nc nc ch1 ch2 in 3 in 7 in 4 in 5 in 6 signal ground Inputs 4, 5 & 6 ch1 (out) ch2 (out) ch1 ch2 -ve Input 7 in 8 ch 1 ch 2 in 9 ch 1 ch 2 NAC 552PS NAC 552PS in +ve ch1 +ve ch2 -ve RC5 control in -ve 6.3 NAC 552 Connected to NAC 552PS Note: For best performance the Burndy and 5 pin DIN cables should be run as close together as possible.
NAC 252 8 Installation and Operation The NAC 252 preamplifier does not incorporate an internal power supply and can be used only in conjunction with the Supercap power supply. Diagram 9.3 illustrates connection of the NAC 252 to the Supercap. 8.1 Source Inputs and Record Outputs The input selector buttons arranged along the upper bank select the source signal to be routed to the power amplifier and the loudspeakers.
Preamplifier NAC 252 8.6 Mute and Mono 8.9 Remote Control Mute and mono functions can be controlled independently for source and record signals via the front panel buttons to the left of the two banks of source and record selection buttons. Mute silences the output signal, while mono sums the left and right channels. 8.7 Display The NARCOM remote handset supplied with the NAC 252 duplicates all configuration and control functions. See Section 24 for more information.
NAC 252 9.2 NAC 252 Rear in 1 cd in 2 tuner in 3 tape Inputs 1, 2 & 6 nc nc ch1 ch2 in 5 in 6 aux 1 aux 2 in 4 av cd/RCA Phono ch1 ch2 signal in 6 (alternative) ground Inputs 3, 4 & 5 ch1 (out) ch2 (out) ch1 ch2 -ve supercap Input 6 (alternative) +ve ch1 +ve ch2 -ve -ve supercap aux 2/RCA Phono ch1 ch2 RC5 control in RS232 interface Note: The NAC 252 AUX 2 input is provided with two sockets.
Preamplifier NAC 282 11 Installation and Operation The NAC 282 preamplifier does not incorporate an internal power supply but must be used in conjunction with either a Naim power amplifier incorporating a preamplifier power output, or with an appropriate Naim power supply. A separate NAPSC supply that provides power to the display and control circuits is also supplied. Diagrams 12.3 and 12.4 illustrate two NAC 282 power supply options. 11.
NAC 282 11.6 Mute and Mono 11.8 Switch-on Mute and mono functions can be controlled independently for source and record signals via the buttons to the left of the two banks of source and record selection buttons. Mute silences the output signal, while mono sums the left and right channels. 11.7 Display The NAC 282 front panel button display can be switched off by pressing the remote handset (in preamplifier mode) disp function.
Preamplifier NAC 282 12.3 NAC 282 Connected to Supercap and NAPSC additional signal output to mono or dual mono power amplifiers mains input and fuse to stereo power amplifiers 12.4 NAC 282 Connected to Hi-Cap and NAPSC to stereo power amplifiers cable direction marker mains input and fuse additional signal output to mono or dual mono power amplifiers Interconnect Cables 240° 5 to 5 pin DIN 13.
NAC 202 14 Installation and Operation The NAC 202 preamplifier does not incorporate an internal power supply but must be used in conjunction with either a Naim power amplifier incorporating a preamplifier power output, or with an appropriate Naim power supply. An optional separate NAPSC supply to provide power to the display and control circuits is also available. Diagram 15.3 illustrates the NAC 202 connected to a Hi-Cap power supply. 14.
Preamplifier NAC 202 14.6 Mute 14.10 Switch-on The mute button silences and restores the output signal. 14.7 Record Monitor The mon button operates the record monitor circuit enabling the recorded output of a suitably equipped recording device to be heard. 14.8 Record Mute In order to minimise power consumption and improve sound quality the NAC 202 record output circuits may be switched off.
NAC 202 15.
Preamplifier NAC 112x 17 Installation and Operation The NAC 112x preamplifier does not incorporate an internal power supply but must be used in conjunction with either a Naim power amplifier incorporating a preamplifier power output, or with an appropriate Naim power supply. Diagram 18.3 illustrates the NAC 112x connected to a Flatcap 2 power supply. 17.1 Input Socket Mapping (Program Mode) The input selector buttons select the source input signal to be routed to the power amplifier and the loudspeakers.
NAC 112x 17.6 Channel Balance Channel balance adjustment is operated electronically within the preamplifier and is controlled by the remote handset bal keys only. Balance will automatically centre as it reaches the mid point. Centring is indicated by a flashing volume control indicator. To resume adjustment once the balance has centred, a handset bal key must be released and re-pressed. 17.7 Mute The mute button silences and restores the output signal. 17.
Preamplifier NAC 112x 18.2 NAC 112x Rear aux 2/RCA Phono ch1 power supply cd/RCA Phono ch1 ch2 upgrade. link plug fitted ch2 RS232 interface RC5 in Inputs 1, 2 & 6 ch1 ch2 nc nc -ve Inputs 3, 4 & 5 ch1 (out) ch2 (out) ch1 ch2 -ve in 6 (alternative) +ve ch1 +ve ch2 cable direction marker mains input and fuse Interconnect Cables 240° 5 to 5 pin DIN in 5 in 4 in 6 aux 2 aux 1 av in 3 tape in 2 in 1 tuner cd Note: The NAC 112x AUX 2 input is provided with two sockets.
NAIT 5i 20 Installation and Operation The NAIT 5i Integrated Amplifier should be installed on a dedicated equipment stand intended for the purpose. Care should be taken to ensure that it is level. The NAIT 5i can be operated from its internal power supply only. No power supply upgrade is possible. 20.1 Inputs The front panel input selector buttons select the source input signal to be routed to the power amplifier and the loudspeakers. The four buttons are labelled cd, tuner, tape and av.
Integrated Amplifier NAIT 5i 20.7 Display The NAIT 5i front panel button display can be switched off by pressing the remote handset (in preamplifier mode) disp function. Any subsequent handset or front panel operation will temporarily restore the display. A second operation of the disp function will permanently restore the display. 20.
Flash Handset 23.1 Introduction PRE (preamplifier mode) Flash is factory pre-programmed to operate any Naim preamplifier or cd player, the NAT 05 tuner and AV2 audio-visual processor. Additional Naim sources may be catered for in the future. Contact your dealer or local representative for information. Page 1 of 2 Flash is supplied without batteries fitted.
Remote Handset Flash and NARCOM 3 AV (av processor mode) 24.1 Introduction Page 1 of 3 NARCOM 3 is a multi-functional remote control handset designed to be used with Naim Audio CD players, integrated amplifiers, preamplifiers and preset tuners. The handset control configuration is based around three types of keys: System Component Keys, Global Keys and Soft Keys. input+ inputmodemode+ osd disp midn menu numeric Selects the next input. Selects the previous input. Selects the previous decode mode.
NARCOM 3 mon Enables the output of appropriately equipped tape machines to be heard while recording. The source to be recorded is chosen by the input selection buttons in the normal way. A second operation of the mon key restores normal operation. Alternatively operates the mono function on appropriately equipped preamplifiers. Compact Disc prev next stop play << & >> repeat pause Selects the previous track or index point. Selects the next track or index point. Stops cd play. Begins cd play.
Remote Handset iCom 25.1 Introduction Compact Disc iCom is a simple remote control handset designed to be used with Naim Audio CD players, integrated and preamplifiers. The handset control configuration is based around three types of keys: System Component Keys, Global Keys and Soft Keys. 25.2 System component keys These keys switch the operation of the Soft Keys into modes appropriate to each system component. System component keys g 4 9 : 8 7 rpt Pauses the cd. Stops cd play. Starts cd play.
NAP 500 26 Installation and Operation The NAP 500 and NAP 500PS should be installed in their final operating locations before connecting cables or switching on. Switch on the source and preamplifier components, with the volume turned down, before switching on the NAP 500. The NAP 500 power button is located on the front panel of the NAP 500PS Power Supply. Care should be taken when siting the NAP 500 to ensure that the top and bottom ventilation grids are not blocked e.g.
Power Amplifier NAP 500 27.1 NAP 500 Connected to NAP 500PS signal input ch1 right speaker left speaker signal input ch2 mains input and fuse Input Ch1 Input Ch2 -ve ch1 -ve nc nc cable direction marker Interconnect Cables NAP 500PS Burndy ch2 28 NAP 500/NAP 500PS Specification Power Output: Quiescent Consumption: Voltage Gain: Input Impedance: Frequency Response: Dimensionss (H x W x D): Weight Mains Supply (NAP 500PS): 140 Watts per channel, 8Ω 700 VA Transient 60VA +29dB 18kΩ -3dB @ 1.
NAP 300 29 Installation and Operation The NAP 300 and NAP 300PS should be installed in their final operating locations before connecting cables or switching on. Switch on the source and preamplifier components, with the volume turned down, before switching on the NAP 300. The NAP 300 power button is located on the front panel on the NAP 300PS Power Supply. Care should be taken when siting the NAP 300 to ensure that the underside fan inlet and rear outlet are not obstructed e.
Power Amplifier NAP 300 30 NAP 300 Connected to NAP 300PS left speaker signal input ch1 right speaker signal input ch2 mains input and fuse Input Ch1 Input Ch2 -ve ch1 -ve nc nc cable direction marker Interconnect Cables NAP 300PS Burndy ch2 31 NAP 300/NAP 300PS Specification Power Output: Quiescent Consumption: Voltage Gain: Input Impedance: Frequency Response: Dimensions (H x W x D): Weight Mains Supply (NAP 300PS): 90 Watts per channel, 8Ω 500 VA Transient 27VA +29dB 18kΩ -3dB @ 2Hz and
NAP 250 32 Installation and Operation The NAP 250 should be installed in its final operating location before connecting cables or switching on. Switch on the source and preamplifier components, with the volume turned down, before switching on the NAP 250. The NAP 250 power button is located on the front panel. The NAP 250 is very heavy and care should be taken when lifting or moving it. Make sure that the surface it is to be placed on can support the full weight. 32.
Power Amplifier NAPV 145 35 Installation and Operation The NAPV 145 is a mono power amplifier intended for use in audio-visual home-theatre systems. The NAPV 145 should be installed in its final operating location before connecting cables or switching on. Switch on the source and preamplifier components, with the volume turned down, before switching on the NAPV 145. The NAPV 145 power button is located on the front panel. The NAPV 145 is very heavy and care should be taken when lifting or moving it.
NAP 200 38 Installation and Operation The NAP 200 should be installed in its final operating location before connecting cables or switching on. Switch on the source and preamplifier components, with the volume turned down, before switching on the power amplifier. The power button is located on the front panel. The NAP 200 can provide power for an appropriate Naim Audio preamplifier. The power supply output is carried on the DIN input socket.
Power Amplifier NAP 150x 41 Installation and Operation The NAP 150x should be installed in its final operating location before connecting cables or switching on. Switch on the source and preamplifier components, with the volume turned down, before switching on the power amplifier. The power button is located on the rear panel. The NAP 150x can provide power for an appropriate Naim Audio preamplifier. The power supply output is carried on the DIN input socket.
NAPV 175 44 Installation and Operation The NAPV 175 is a three channel power amplifier intended for use in home-theatre systems. The three channels provide power to drive a centre channel speaker and a pair of either main front or surround channel speakers. Audio line level input is via two 4-pin DIN sockets - one for the centre channel and one for the main or surround pair. The NAPV 175 should be installed in its final location before connecting cables or switching on.
Power Amplifier NAP 6-50 47 Installation and Connection The NAP 6-50 is a six channel power amplifier intended for use in multi-room audio systems. The six channels are configured as three sets of two (left and right). The three sets are intended to provide audio power to drive one pair of loudspeakers in three multi-room “zones”. Audio line level input for each zone is via 4-pin DIN sockets. The NAPV 175 is heavy and care should be taken when lifting or moving it.
Supercap, XPS, Hi-Cap 50 Installation Power supplies should be installed in their final location before connecting cables or switching on. Ensure that power amplifiers are switched off and the preamplifier volume is turned down before power supplies are switched on. The power buttons are located on the front panel. Power supplies are heavy and care should be taken when lifting or moving them. Make sure that the surface on which they are to be placed can support their full weight. 50.
Power Supply Flatcap 2, NAPSA, NAPSC 51 Installation Power supplies should be installed in their final location before connecting cables or switching on. Ensure that power amplifiers are switched off and the preamplifier volume is turned down before power supplies are switched on. The Flatcap 2 and NAPSA are heavy and care should be taken when lifting or moving them. Make sure that the surface on which they are to be placed can support their full weight. 51.
Power Supplies 52 Power Supply Specifications Product Supercap XPS Hi-Cap Flatcap 2 NAPSA NAPSC Outputs: 13 x 24V 2 x 12V 2 x 24V 2 x 22V 2 x 24V 116Vac 18.5V Dimensions (mm): (H x W x D) Weight: Mains Supply: 87 x 432 x 314 ±22V ±10V 2 x 15V 87 x 432 x 314 87 x 207 x 314 70 x 432 x 304 87 x 207 x 314 57 x 121 x 187 11.6kg 12.4kg 7.35kg 5.4kg 100-120V or 220-240V, 50/60Hz 6.75kg 2.
37
Naim Audio Limited, Southampton Road, Salisbury, England SP1 2LN Naim Audio Limited, Southampton Road, Salisbury, England SP1 2LN Telephone: +44 (0) 1722 332266 Fax: +44 (0) 1722 412034 www.naim-audio.com Telephone: +44 (0) 1722 332266 Fax: +44 (0) 1722 412034 www.naim-audio.com Part No. OWMDV Part No. 0WMAM 12-001-0041 Drawing No. NA102001-400 Drawing No.