CONGRATULATIONS ON OWNING YOUR NEW NAUTICA WATCH DEVELOPED FROM ADVANCED ELECTRONICS TECHNOLOGY, THE MOVEMENT IS MANUFACTURED FROM THE BEST QUALITY COMPONENTS AND POWERED BY A LONG LIFE BATTERY.
NAUTICA watches have been developed with the highest attention to quality, function and detail, as befits the NAUTICA tradition. Please read the following instructions carefully to fully understand all of the functions of your finely crafted timepiece. WATER-RESISTANCE If your watch is water-resistant, it will be indicated on the watch face or on the caseback. • 50 Meter Water-Resistant watch withstands water pressure to 86p.s. i.a.
INDIGLO® NIGHT-LIGHT If your watch has “INDIGLO” on the dial, your watch is equipped with the INDIGLO Night-Light. To activate this feature, depress the crown or the pusher on the left side of the watch to illuminate the entire dial for easy reading during nighttime or low light conditions. Light will appear immediately. Your NAUTICA watch featuring INDIGLO Night-Light contains a patented electroluminescent technology (U.S. Patent Number 4,527, 96 and 4,775,964).
SCREW-IN SETTING CROWN ATTENTION This is a screw down crown Do not pull Please read instruction booklet before operation SCREW-IN SETTING CROWN STICKER Some deep-depth water-resistant watches require the setting crown to be screwed in to ensure water-resistant. If your Nautica watch has a transparent sticker at back of the case back (diagram above) please unscrew the crown before setting your watch, and the crown must be screwed in after setting the watch.
ELAPSED TIME RING If your watch is equipped with a rotatable outer dial with numbers and indicators, this Elapsed Time Ring may be used to indicate the length of time remaining for an activity or the starting time of an activity. TIME REMAINING - set the outer ring so that the traingle is pointing to the time the activity is to end. STARTING TIME - set the triangle on the time the activity is to begin. TACHYMETER A tachymeter measures the speed at which the wearer has traveled over a measured distance, i.
CHRONOGRAPH MODELS STOPWATCH 1/20SEC.
TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position “A” CALENDAR To set the calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3.
ACCUMULATED ELAPSED TIME MEASUREMENT: 1. 2. 3. 4. 5. Press Press Press Press Press pusher pusher pusher pusher pusher “A” “A” “A” “A” “B” to to to to to start timing stop timing restart timing stop 2nd timing reset Example of using split time measurement for two runners Two runners can be timed simultaneously; the first runner’s time can be recorded while the second runner’s time will continue to be accumulated until he finishes. SPLIT TIME MEASUREMENT: 1.
TO ADJUST STOPWATCH HANDS: 1. Pull crown to “C” position 2. Press pusher “A” for 2 seconds 3. Press pusher “B” to “0” setting for the 1/20 sec. hand. If the hand is not at “0” or “12” position, then, press pusher “B” repeatedly, until the hand moves by each intervaI and returns to “0” or “12” position 4. Press pusher “A” for 2 seconds 5. Press pusher “B” to “0” setting for the stopwatch sec. hand.
CHRONOGRAPH HAND 1/5 SECOND PUSHER “A” ABC HOUR HAND CROWN POSITION PUSHER “B” PUSHER “C” MINUTE HAND ALARM 8154/220 2, 6, 10 Three – Eye Chronograph with Alarm Note: Note: Note: Note: Note: Crown position “A”, “B” & “C” Pusher “A” (Top), “B” (Bottom) Left eye “30 minute totalizer” Right eye “second hand” Bottom eye “day calendar” This chronograph has 4 functions: TIME, DAY & DATE, STOPWATCH, ALARM TIME To set the time: 1. Pull crown to position “C” 2.
DAY & DATE CALENDAR To set the day calendar: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct day (bottom eye) 3. Push crown to position “A” To set the date calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct date (window @ 4) 3. Push crown to position “A” Note: It is not possible to correct the date between 9 p.m. and 0:30 a.m. STOPWATCH The stopwatch is capable of measuring: 1. Minutes (up to 30 minutes) 2.
STANDARD STOPWATCH MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “B” to reset ACCUMULATED ELAPSED TIME MEASUREMENT: 1. 2. 3. 4. 5. Press Press Press Press Press pusher pusher pusher pusher pusher “A” “A” “A” “A” “B” to to to to to start timing stop timing restart timing stop 2 nd timing etc, etc. reset SPLIT TIME MEASUREMENT: 1. 2. 3. 4. 5.
ALARM To set the alarm: 1. Pull crown to position “B” 2. Turn crown counter clockwise to set alarm (colour hand) 3. Push crown to position “A” To activate the alarm: 1. Press pusher “C” to activate the alarm. Watch beeps twice 2. Press pusher “C” again to de-activate alarm. Watch beeps once 3.
SECONDS PUSHER A ABC MINUTE CROWN POSITION DATE PUSHER B 8161/202 2, 6, 10 THREE - EYE CHRONOGRAPH Note: Note: Note: Note: Note: Crown position “A”, “B” & “C” Pusher “A” (Top), “B” (Bottom) Left eye “minute totalizer” Right eye “small second” Center eye “date indicator” This Chronograph watch has 3 functions: TIME CALENDAR STOPWATCH 19
TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position “A” CALENDAR To set the calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3. Push crown to position “A” STOPWATCH The stopwatch is capable of measuring: 1. 1 minute elasped up to 30 minutes (left eye) 2. Chronograph hand 1/5 second Before using the stopwatch, reset the stopwatch hands To the “60” position by means of pusher “B”.
STANDARD STOPWATCH MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “B” to reset ACCUMULATED ELAPSED TIME MEASUREMENT: 1. 2. 3. 4. 5. Press Press Press Press Press pusher pusher pusher pusher pusher “A” “A” “A” “A” “B” to to to to to start timing stop timing restart timing stop 2nd timing reset SPLIT TIME MEASUREMENT: 1. 2. 3. 4. 5.
CHRONOGRAPH HAND 1/5 SECOND PUSHER “A” ABC 4 4 1 HOUR HAND CROWN POSITION 5 2 3 PUSHER “C” PUSHER “B” MINUTE HAND ALARM 8154/221 2, 6, 10 Three – Eye Chronograph with Alarm Note: Note: Note: Note: Note: Crown position “A”, “B” & “C” Pusher “A” (Top), “B” (Bottom) Left eye “30 minute totalizer” Right eye “second hand” Bottom eye “day calendar” This chronograph has 4 functions: TIME, DAY & DATE, 5 HOUR CHRONOGRAPH, ALARM TIME To set the time: 1. Pull crown to position “C” 2.
DAY & DATE CALENDAR To set the day calendar: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct day (bottom eye) 3. Push crown to position “A” To set the date calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct date (window @ 4) 3. Push crown to position “A” Note: It is not possible to correct the date between 9 p.m. and 0:30 a.m. 5 hour STOPWATCH Key Features of Stopwatch Mode: 1. This is a stopwatch for timing long hours chrono function. 2.
TO START THE STOPWATCH: • Push pushers “A”, the big sec will start counting at intervals of 1/5 sec for the first thirty minutes. TO STOP THE STOPWATCH: • Push the pusher “A” again to stop timing. TO RESET THE STOPWATCH: • Push pushers “B”, to reset the stopwatch. Both the big sec. hand and small hand at the small eve at 10 o’clock position will go back to 12 o’clock position.
2. Push the pusher “B” to reset the small hand of the eve at 10 o’clock position. After the pusher is pushed, the small sec hand will reach the “30” position exactly. 3. Push the pusher “B” to reset the big sec. hand. When it moves close to the 11 o ‘clock position, adjust it by pushing the button sec by sec until it reaches the 12 o’clock position exactly. 4. Push the pushers “A” and “B” simultaneously and hold for 2 seconds to deactivate the reset mode. SPLIT TIME MEASUREMENT FOR TIMING TWO RUNNERS: 1.
PERMANENT SECOND HAND MINUTE CHRONO HAND PUSHER “A” ABC STOPWATCH SECOND HAND CROWN POSITION PUSHER “B” HOUR CHRONO HAND DATE 5030D Note Note Note Note Note : : : : : Crown position “A” “B” and “C” Pusher “A” (Top right) “ B” (Bottom Right) 6 o’ clock eye - Hours elapsed up to 12 hours 9 o’clock eye - Minutes elapsed up to 30 minutes 3 o’clock eye - Permanente second hand This Chronograph watch has 3 functions : TIME, CALENDAR, STOPWATCH TIME To set the time : 1. Pull crown to position “C” 2.
CALENDAR To set the Calendar 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3. Push crown back to position “A” STOPWATCH This stopwatch is capable of measuring : Chrono Hours elapsed up to 12 hours ( 6 o,clock eye) Chrono Minutes elapsed up to 30 minutes ( 9 o,clock eye ) Stopwatch Second up to 1 minute. ( Big second hand ) Before using the stopwatch, reset stopwatch chrono hands to the “12” and “0” position STANDARD STOPWATCH MEASUREMENT 1. Press pusher “A” to start timing 2.
SPLIT TIME MEASUREMENT Example of using split time measurement for two runners. Two runners can be timed simultaneously; the first runner’s time can be recorded while the second runner’s time will continue to be accumulated until he finishes. 1. Press pusher “A” to start the timing of the first and second runner 2. Press pusher “B” to stop and record the timing of the first runner. ( Once pusher “B” is activated, even though the chrono minute hand and the big stopwatch sec.
After finish adjusting big sec. stopwatch hand, press crown back to position “A” to terminate the adjustment. TO ADJUST THE HOUR CHRONO HAND After activate the corrective mode; if the hour chrono hand in not located at “12” or “0” position, press pusher “B” once to activate the corrective mode of the hour chrono hand. Press pusher “A” continuously or repeatedly until the hand moves by each interval and returns to “12” and “0” position. Press crown back to position “A” to terminate the adjustment.
24 HOUR HAND STOPWATCH MINUTE HAND PUSHER “A” ABC CROWN POSITION STOPWATCH SECOND HAND PUSHER “B” SECOND HAND DATE OS20 Note: Crown position "A" "B" &"C" Note: Pusher "A" ( Top Right), Pusher 'B" ( Bottom Right) Note: 3 o'clock eye - 24 hour hand Note: 6 o'clock eye - second hand Note : 9 o'clock eye - stopwatch minute hand This Chronograph watch has three functions : TIME, CALENDAR, STOPWATCH TIME To set the time: 1. Pull crown to position "C" 2.
Remarks: When crown is pushed back to position "A," small second hand begins to run. CALENDAR To set the calendar 1. Pull crown to position "B" 2. Turn crown counter-clockwise to set calendar 3. Push crown to position "A" STOPWATCH The stopwatch is capable to measure and display time in 1/1 second united up to maximum of 59 minutes 59 seconds. 1. Press pusher "A" to start timing 2. Press pusher "A" again to stop timing 3.
MINUTES HAND STOPWATCH MINUTE HAND PUSHER “A” CROWN POSITION HOUR HAND ABC STOPWATCH SECOND HAND PUSHER “B” PERMANENT SECOND HAND Note: Note: Note: Note: DATE OS11 Crown Position “A” “B” & “C” Pusher “A” (Top right), Pusher “B” (Bottom Right ) 12 o’clock eye chrono minute hand 6 o’clock permanent second hand This Chronograph watch has 3 functions TIME, CALENDAR, STOPWATCH TIME To set the time : 1. Pull crown to position “C” 2. Turn crown counter clockwise to correct time 3.
CALENDAR To set the calendar 1. Pull out the crown to position B. 2. Turn crown counter clockwise to correct calendar 3. Push in the crown to position A. STOPWATCH This watch is capable to measure and display 1 second unit up to maximum of 60 minutes 1. Press pusher “B” to enter to chrono mode. 2. Press pusher “A” to start the timing 3. Press pusher “A” again to stop timing 4. Press pusher “B” to reset CORRECTING STOPWATCH HANDS TO “12” OR “0” POSITION 1. Pull crown to position “B” 2.
STOPWATCH MINUTE HAND PUSHER “A” CROWN POSITION CHRONOGRAPH HAND 1/5 SECOND ABC PUSHER “B” SECOND HAND YM91 Note : Crown position “A” “B” and “C” Note: Pusher “A” ( Top Right ), “B” ( Bottom Right) Note: 12 o’clock eye - Stopwatch minute hand Note : 6 o’clock eye - Second hand This Chronograph watch has three functions : TIME, CALENDAR, STOPWATCH TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3.
CALENDAR To set the calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3. Push crown to position “A” STOPWATCH This stopwatch is capable of measuring : – 1/5 second elapsed up to 60 minutes – After 60 minutes, it will start counting again from “0” repeatedly up to 12 hours Before using the stopwatch, reset the stopwatch hands To the “12” and “0” position. STANDARD STOPWATCH MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3.
SPLIT TIME MEASUREMENT: 1. Press pusher “A” to start the timing of the first runner 2. Press pusher “B” to stop and record the timing of the first runner. (Once pusher B is activated, even though the stopwatch 1/20 sec. hand and the big stopwatch sec. hand stop on the dial, the stopwatch still continues to time internally.) 3. Press pusher “B” to start the timing of the second runner. The stopwatch sec. hand will jump to show internal accumulated time and to carry on timing of the second runner. 4.
37
LIMITED WARRANTY The Basic Coverage: This NAUTICA watch (but not any battery, crystal, case, band or strap) is warranted to the owner for a period of FIVE YEARS from the date of purchase against defects In manufacture by Nautica Watches - not by the dealer from whom the watch was purchased. What Nautica Watches Will Do: If this watch develops such a defect within the five year period it will be repaired (i. e.
Your Rights Under Implied Warranties and State Law: THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESSED WARRANTIES, OBLIGATIONS OR LIABILITIES. NAUTICA WATCHES LIMITS THE DURATION OF ANY WARRANTY IMPLIED BY STATE LAW, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO FIVE YEARS FROM THE DATE OF ORIGINAL PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
