TIME CRISIS III DX (CAMERA) OPERATORS MANUAL IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY Part No.
Page 2
is a copyrighted anti-copying technology created by Sony Corp. This mark does not necessarily imply compatibility with other products bearing the “MAGICGATE” trademark. is a trademark of Sony Corporation. The CD-ROM supplied with the machine must not be copied, modified, publicly distributed, or used for purposes other than operation of the machine. The contents of the CD-ROM is protected by copyright. Infringements of copyright law may be subject to criminal penalties.
Contents OPERATORS MANUAL ............................................................................................................................. 1 GENERAL SAFETY CONSIDERATIONS .................................................................................................. 6 ALLGEMEINE SICHERHEITSHINWEISE ................................................................................................. 8 GENERELLE SIKKERHEDSOVERVEJELSER ...............................................................
6. MAINTENANCE .................................................................................................................................. 62 6-1 Replacing the Pedal Switch ....................................................................................................... 64 6-2 Greasing the Pedal Assy Plunger ............................................................................................... 65 6-3 Replacing the Pedal Plunger .....................................................
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private use, without permission from NAMCO EUROPE LIMITED. While the information contained in this manual is given in good faith and was accurate at the time of printing, NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
NOTES ON INSTALLATION l NEVER turn the power to the machine ON until installation has been completed. l In order to prevent possible electric shocks, be sure that the equipment is connected to the mains with a securely connected earthed plug. l So that customers are not injured by the movement of the equipment, ensure that there is at least 500mm seperation between other equipment or walls.
D Dieses Dokument darf in keiner Weise vervielfältigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datenträger (Suchsysteme), die Weitergabe oder sonstiges Kopieren für den gewerblichen und privaten Gebrauch sind untersagt und bedürfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED. Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behält sich jedoch das Recht zu Änderungen ohne vorherige Bekanntgabe vor.
HINWEISE ZUR AUFSTELLUNG l NIEMALS das Gerät einschalten bevor die Aufstellung völlig abgeschlossen ist. l Zur Vermeidung von Elektroschlägen muß das Gerät mit einem ordnungsgemäß geerdetem Netzstecker an die Stromversorgung angeschlossen werden. l Um zu vermeiden, daß Kunden durch die Gerätebewegungen verletzt werden, muß ein Sicherheitsabstand zu anderen Geräten und Wänden von mindestens 50cm eingehalten werden.
Denne udgivelse må ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den må heller ikke lagres i et eftersøgningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra Namco Europe Limited. Da informationerne i denne manual er givet med god tro og var korrekt på udskivningstidspunktet, forbeholder Namco Europe Limited sig retten til, at foretage ændringer og forandringer uden varsel.
PUNKTER OM INSTALLATION l l Tænd aldrig for strømmen til maskinen før installering er fuldført. l For at kunder ikke kommer til skade ved spillets bevægelser sikres, at der er mindst 50cm afstand til andre maskiner og vægge. i For at undgå skader på maskinen p.g.a. fejlbetjening sikres, at spændingen på hovedstrømmen er 230 volt AC. For at undgå mulige elektriske stød sikres, at maskinen er forbundet til hovedstrømmen med sikkert monterede jordstik.
No se permite la reproducción total ni parcial de esta publicación por ningún medio mecánico, fotográfico o electrónico, grabaciones fonográficas, ni su almacenamiento informático, su transmisión o su copia, ya sea para uso público o privado, sin permiso de NAMCO EUROPE LIMITED. Si bien la información contenida en este manual se da de buena fe y es correcta en el momento de su impresión, NAMCO EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.
NOTAS DE INSTALACIÓN. l JAMÁS ENCIENDA la máquina antes de haber completado la instalación. l Para evitar posibles descargas eléctricas, asegúrese de que la máquina está conectada a la red con un enchufe provisto de toma de tierra. l Para que los usuarios no sufran lesiones debido al movimiento del juego, asegúrese de que hay al menos 500 mm de separación entre éste y otras máquinas o las paredes.
Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d’enregistement phonographique. Ces informations ne seront ni stockées grâce à un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l’autorisation de NAMCO EUROPE LIMITED.
NOTES D’INSTALLATION l NE JAMAIS mettre le jeu en marche avant que l’installation ne soit complétement effectuée. l Afin de prévenir une éventuelle électrocution, s’assurer que la machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité. l Afin que les clients ne soient pas blessés par les mouvements du jeu, s’assurer qu’il existe au moins 500 mm de séparation aves les autres jeux ou les murs.
ও ÊáíÝíá ìÝñïò áõôÞò ôçò Ýêäïóçò äåí ìðïñåß íá áíáðáñá÷èåß ìå ïðïéïäÞðïôå ìç÷áíéêü ,öùôïãñáöéêü Þ çëåêôñïíéêü ìÝóï , Þ ìå ìïñöÞ öùíçôéêÞò ç÷ïãñÜöçóçò êáé ïýôå íá áðïèçêåõôåß ìå åðáíïñèùôéêü óýóôçìá , íá ìåôáäïèåß Þ íá áíôéãñáöåß ãéá äçìüóéá Þ éäéùôéêÞ ÷ñÞóç , ÷ùñßò ôçí Üäåéá ôçò NAMCO EUROPE LIMITED. Êáèþò áõôÝò ïé ðëçñïöïñßåò óå áõôü ôï åã÷åéñßäéï Ý÷ïõí äïèåß ìå êáëÞ ðßóôç êáé áêñéâþò ôçí þñá ôçò ôýðùóçò , ç åôáéñåßá NAMCO EUROPE LIMITED êñáôÜåé ôï äéêáßùìá íá êÜíåé ïðïéåóäÞðïôå áëëáãÝò ÷ùñßò åéäïðïßçóç.
ÓÇÌÅÉÙÓÅÉÓ ÃÉÁ ÔÇÍ ÅÃÊÁÔÁÓÔÁÓÇ l ÐÏÔÅ íá ìçí áíÜâåé ôï ìç÷Üíçìá åÜí äåí Ý÷åé ïëïêëçñùèåß ç åãêáôÜóôáóç. l l Ãéá ôçí áðïöõãÞ çëåêôñéêþí óïê ðñÝðåé ôï ìç÷Üíçìá íá Ý÷åé ãåéùèåß. i Ãéá ôçí áðïöõãÞ âëÜâçò óôï ìç÷Üíçìá ëüãï ëÜèïò ëåéôïõñãßáò , ðñÝðåé ç ðáñï÷Þ íá åßíáé 230volt AC.. Ãéá ôçí áðïöõãÞ êéíäýíïõ óå êÜðïéïí ðáßêôç , ðñÝðåé ôï ìç÷Üíçìá íá Ý÷åé áðüóôáóç ôïõëÜ÷éóôïí 500mm áðü Üëëï ìç÷Üíçìá Þ ôïß÷ï.
Nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza l’autorizzazione di NAMCO EUROPE LIMITED. Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione.
NOTES D’INSTALLATION l NON ACCENDERE MAI la macchina finchè l’installazione non è stata completata. l Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure. Perchè i clienti non siano feriti dal movimento del gioco, assicurarsi che ci siano almeno 500mm di distanza rispetto alle altre macchine o rispetto al muro.
Ingen del av denne utgivelsen må reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra NAMCO EUROPE LIMITED. Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP LIMITED seg retten til å lage forandringer uten varsel.
MERKNADER VED INSTALLASJON l l Slå ALDRI på maskinens strømforsyning før installasjonen er fullført. l For å forhindre at kundene blir skadet av spillets bevegelige deler. forsikre deg om at det er minst 500mm avstand mellom andre maskiner eller vegger. i For å forhindre eventuelle elektriske sjokk, forsikre deg om at maskinen er koplet til et strømnett med ordentlig jording. For å forhindre skade på maskinen p.g.a. feil bruk, sørg for at spenningen til hoved strømforsyningen er 230Volt AC.
Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe Limited.
Opmerkingen aangaande Installatie l Sluit de machine nooit aan op de stroomtoevoer totdat de installatie is voltooid. l Om mogelijke electrische schokken te voorkomen, dient ervoor gezorgd te worden dat de machine middels een goed vastzittende aardstekker op het lichtnet is aangesloten. l Om ervoor te zorgen dat klanten niet gewond raken door de beweging van het spel, dient ervoor gezorgd te worden dat er minimaal 500mm ruimte is tussen andere machines of muren.
Nenhuma parte desta publicacão poderá ser reproduzida por processos mecanográficos, fotográficos, electrónicos ou ainda sob a forma de gravacão sonora nem tão pouco poderá ser gravada através de sistemas informáticos transmissiveis ou de outra forma copiados para uso publico ou privado sem autorização expressa da NAMCO EUROPA LIMITADA. A informação contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicação.
NOTAS SOBRE A INSTALAÇÃO l NUNCA ligar a maquina sem que a instalação esteja completamente finalizada. l Afim de evitar possiveis choques electricos, certifique-se que a maquina está ligada à rede de alimentação com uma ficha protegida com circuito de terra. l Afim de evitar ferimentos pessoais nos clientes, provocados pelo movimento da maquina, certifique-se que existe pelo menos 500mm de separação entre outras maquinas ou paredes.
Ingen del av denna publikation får reproduceras, varken fotografiskt, elektroniskt eller i någon form av ljudinspelning. Det får inte heller lagras i något återvinningssystem, översändas eller på annat sätt kopieras för offentlig eller privat användning, utan tillstånd från NAMCO EUROPE LIMITED. Eftersom informationen i denna manual lämnas ut i god tro och var korrekt när den trycktes, reserverar sig NAMCO EUROPE LIMITED för ändringar.
ATT BEAKTA VID INSTALLATION l l Sätt aldrig på strömmen på maskinen innan installationen är klar. l För att undvika skador av spelets rörelser, försäkra dig om att det finns ett avstånd på minst 500 mm till annan maskin eller vägg. i För att undvika skador på maskinen p g a felaktigt handhavande, försäkra dig om att strömstyrkan är 230 volt AC.
Tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman NAMCO EUROPE LIMITED:in lupaa. Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. NAMCO EUROPE LIMITED:illä on kuitenkin oikeus muutoksiin ilman erillistä ilmoitusta. Tämä laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiivejä: 89/336/EEC ja 72/23/EEC (EN55014-1, EN55014-2 ja EN 60335-2-82 standardit).
ASENNUSHUOMIOITA l Älä koskaan kytke laitetta päälle ennen kuin asennus on suoritettu loppuun. l Tämän laitteen virtalähde on kytkettävä maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sähköiskun vaaraa ei olisi. l Varmista, että laitteen ja seinän tai toisen laitteen välissä on vähintään 500 mm, jotta asiakkaat eivät loukkaannu laitteen likkumisesta johtuen. i Varmista, että virtalähteen jännite on 230 V AC, jotta ei laite vioitu. Huomio: Jos tämä laite sijoitetaan liukkaalle esim.
1.
2.
3. HOW TO PLAY This is a gun shooting game where players press on a foot pedal to hide behind an object to avoid an enemy attack, then release the pedal to get out from behind the object and attack the enemy. HOW TO CONTROL 1. Step on the pedal = 2. Release the pedal = Attack position. In this position you can shoot the enemy. You are also subject to an attack. Defence position. In this position you are hidden behind an object and cannot be hit by the enemy. Releasing the pedal also reloads the gun.
4. INSTALLATION 1. 2. 3. 4. 5. 6. 쮕 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. l This machine is designed for INDOOR USE ONLY. Do not install in the following places. Outdoors Direct Sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature. Places where it would be in the way of emergency exits or fire extinguishing equipment.
1. 2. CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS A l’extérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits où il y a des risques de fuite d’eau, près de ventilateurs ou source de chaleur, aux endroits très chauds ou froids. Dans des zones de proximité des sorties de secours ou d’accès aux équipements d’extinction du feu.
1. 2. Buiten In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen. Op plaatsen die niet vlak zijn.
4-1 Notes on Installation l WARNING • NEVER turn the power to the machine ON until installation has been completed. l WARNING • In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug. l WARNING • So that customers are not injured , ensure that there is at least 500mm separation between other machines or walls.
4-2 Joining the Monitor Cabinets 1. Place the two Monitor Cabinets together, and remove the Lower Rear Door on each cabinet. 2. Fit the hex head screw (M8x40), wingnut (M8). and flat washers to join the rear of the Monitor Cabinets together. Monitor Cabinet Assy Flat Washer Wing Nut (M8) Hex head screw (M8x40) Flat Washer 3. Fit 4off Socket cap screws (M8x40) to the front of the Monitor Cabinets, leaving approx 5mm of the screws protruding. Monitor Cabinet Monitor Cabinet Assy approx.
4. Remove 4off security screws (M5x12) and remove the Joint Box Cover. 5. Fit the Joint Box to the 4off socket head screws (M8x40) and tighten the screws. 6. Feed the looms from both Monitor Cabinets into the Joint Box, and connect the connectors.
4-3 Fitting the Header Assembly l The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly. l The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. Steps, Step Stool etc.) 1.
4-4 Connecting the Coin Tower Assy to the Monitor Cabinet 1. Fit 4off Socket cap screws (M8x16) to retain the Joint Box Assy tot he Coin Tower Assy. 2. Feed the looms from the Gun Tower Assy into the Joint Box, and connect the connectors. Joint Box Assy Socket cap screw (M8x16) Coin Tower Assy Connectors 3.
4-5 Adjusting the Level Adjusters 1. When the game is in it’s final position, lower the six (6) Level adjusters, 4 on the Monitor Cabinet and 2 on the Coin Tower Assy, with a spanner, so that all castors are raised from the floor by approximately 5mm. Tighten the lock nuts with a spanner to ensure that the Level Adjusters do not move. Castor Lock Nut Approx.
4-6 Fitting the Pedal Assemblies 1. Remove 2off security screw (M5x12) and remove the Joint Bracket from the Pedal Assy. (Take care not to lose the screws as these will be used to fit the Pedal Assy. Pedal Assy Security screw (M5x12) Joint Bracket 2. Fit the Joint bracket to the Coin Tower Assy, finger tight only, with the 2off security screw (M5x12) 3.
4-7 Fitting the DVD-ROM The DVD-ROM must be inserted with the game power ON. To prevent electric shock, accident or injury, do not touch any parts other than those specified below. 1. Remove the rear panel from the Monitor Cabinet. 2. Pull the actuating button of the Interlock Switch to turn the game ON. 3. Press the Eject button of the DVD-ROM drive to eject the tray. Note: The tray will automatically retract after approx 10 seconds. PCB Assy DVD-ROM Drive Indicator Lamp Eject Button 4.
5. ADJUSTMENTS 쮕 l Adjustment or maintenance on this machine should be carried out by qualified personnel only. Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem Fachpersonal vorgenommen werden. eller vedligehold af denne maskine bør kun udføres af Justeringer kvalificeret personale. ও Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo por personal cualificado.
5-1 Adjustment Switches The Adjustment switches are located inside the coin door. 1. Service Switch. Press this switch to obtain game credits without incrementing the play meter. 2. Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 52 "Test Mode" page 46) 3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode. 4.
5-2 Test Mode 1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will be displayed on the monitor. 2. Select the test required by using the select up/down switch. The colour of the selected test will change. 3. Activate the test by pressing the Enter switch. Select “EXIT” in each test to return to the “Menu Screen”. 4. After testing is completed, slide the test switch to the “OFF” position to return to normal game mode.
5-2-1 Coin Options 1. Select “COIN OPTIONS” on the menu screen to set the game cost and related settings. The following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Use the Select Up/Down switch to change the setting. 4. Press the Enter button to return to option select mode. 5. Select “EXIT” and press the Enter button to return to the menu screen. Note:- The price of play on this machine is set within the Cashflow Coin Mech.
5-2-2 Game Options 1. Select “GAME OPTIONS” on the menu screen to set the game variables, the following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Use the Select Up/Down switch to change the setting. 4. Press the Enter button to return to option select mode. 5. Select “EXIT” and press the Enter button to return to the menu screen.
5-2-3 I/O Test 1. Select “I/O TEST” on the menu screen to test the I/O PCB, initialize the gun accuracy and to test switches and gun solenoids, the following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Select “EXIT” and press the Enter button to return to the menu screen.
5-2-3-1 1. I/O PCB Check Select “I/O PCB CHECK” on the I/O TEST menu screen, the following screen is displayed. I/O TEST DIP : 1234 LINK : ON 2 LINK AS :1 [ON:RED] (LEFT) I/O PCB CHECK : Connect OK namco ltd. : TSS-I/O; ver2.11; GUN EXTENSION EXIT SELECT SW : CHOOSE ENTER SW : ENTER This screen displays the condition of the LINK system and the type and version of the I/O PCB.
5-2-3-2 1. Gun Initialize Select “GUN INITIALIZE” on the I/O TEST menu screen (or press and hold the Service Switch whilst turning the Test Switch on), the following Aim Check screen is displayed. GUN INITIALIZE +OUT OF SCREEN+ (a) This mark appears when the gun is pointed at the screen. AIM AT SCREEN TO CHECK GUN ACCURACY PUSH SERVICE SW : ADJUST GUN SIGHT ENTER SW :EXIT 2 The Gun Crosshair is displayed at the point on the screen at which the gun is pointed.
3. To set the gun aiming press the Service Button or the Foot Pedal while the Aim Check scren is displayed. The following screen will be displayed. GUN INITIALIZE AIM AT CENTER OF THE CROSS AND PULL GUN TRIGGER 4. Aim and shoot once at the cross hair displayed at the centre of the screen. The following screen will be displayed. GUN INITIALIZE AIM AT CENTER OF THE CROSS AND PULL GUN TRIGGER 5. Aim and shoot once at the cross hair displayed at top left of the screen.
6. Aim and shoot once at the cross hair displayed at the top right of the screen. The following screen will be displayed. GUN INITIALIZE AIM AT CENTER OF THE CROSS AND PULL GUN TRIGGER 7. Aim and shoot once at the cross hair displayed at the bottom right of the screen. The following screen will be displayed. GUN INITIALIZE AIM AT CENTER OF THE CROSS AND PULL GUN TRIGGER 8. Aim and shoot once at the cross hair displayed at the bottom left of the scren. This complete the Gun Sight Adjustment.
• Observe the following points when adjusting the gun sight. • Hold the gun and aim so that the top edge of the rear sight is at the same height as the horizontal line of the crosshair displayed on the screen • Also, align the top edge of the front sight with the horizontal line of the crosshair on the screen. • Align the centre of the top sections of the front and rear sights of the gun with the centre of the crosshair on the screen, and fire the gun.
5-2-3-3 1. Switch Test Select “SWITCH TEST” on the I/O TEST menu screen, the following screen is displayed. I/O TEST DIP : 1234 [ON:RED] LINK : ON 2 LINK AS :1 (LEFT) SWITCH TEST COIN 0 SERVICE OFF TEST ON UP SELECT OFF DOWN SELECT OFF ENTER OFF GUN TRIGGER OFF FOOT PEDAL OFF SENSOR ON SELECT SW : CHOOSE (a) (b-h) (i) (a) (b) (c) (d) (e) (f) (g) (h) (i) ENTER SW : ENTER The counter will increase each time a credit signal is sent to the game PCB.
Interruption Sensor The game cannot be played if the sensor is blocked by an object placed on top of the Control Assy. A message appears on the screen if the sensor is blocked during operation. Do not place any item on top of the game machine. Remove the item to continue the game play. A warning illustration is displayed on the screen. Message screen displayed when the sensor is blocked • • If the sensor is blocked during the Attract Mode, the message appears after coins are inserted.
5-2-3-4 1. Solenoid Test Select “SOLENOID TEST” on the I/O TEST menu screen, the following screen is displayed. DIP LINK LINK AS I/O TEST : 1234 [ON:RED] : ON 2 :1 (LEFT) SOLENOID TEST PULL GUN TRIGGER TO ACTION EXIT SELECT SW : CHOOSE ENTER SW : ENTER 2. The gun solenoid will operate each time the gun trigger is pulled. 3. Select “EXIT” and press the Enter button to return to the menu screen.
5-2-4 Monitor Test 1. Select “MONITOR TEST” on the menu screen to make adjustments to the monitor. The following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Press the Enter button to return to Monitor Test Screen. 4. Select “EXIT” and press the Enter button to return to the menu screen.
5-2-5 Sound Test 1. Select “SOUND TEST” on the menu screen to test the audio and adjust the volume settings. The following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Use the Up/Down switch to change the setting. 4. Press the Enter button to return to item select mode 5. Select “EXIT” and press the Enter button to return to the menu screen.
5-2-6 ADS Data (Bookkeeping) 1. Select “ADS DATA” from the menu screen to view the bookkeeping details. 2. Select “EXIT” and press the enter switch to return to the menu screen. 5-2-7 Others 1. Select “OTHERS” on the menu screen to display the ROM version, to set the on screen language, display mode and to set all settings to factory default. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3.
5-3 Cleaning 5-3-1 Cleaning the Gun Lenses • Clean the gun Lenses every day to maintain accuracy. Use a soft lint free cloth to wipe the lenses. • Do not use detergents or chemicals to clean the lenses • Take care not to scratch the lenses. 5-3-2 • Cleaning the Window Covers Clean the Camera window covers on the Gun Tower Assy every day to maintain gun accuracy. Use a soft lint free cloth to wipe the lenses. Gun position detection can be affected if the covers are scratched.
6. MAINTENANCE 쮕 ও Adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the POWER to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, service or repairs etc.) Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem Fachpersonal vorgenommen werden. Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der Netzstecker gezogen werden.
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine UITgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.) Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente por pessoal qualificado. Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutenção. (identifação de avarias, reparação etc.
6-1 Replacing the Pedal Switch 1. Remove 4off security screw (M5x12) and remove the switch cover plate. urity screw (M5x12) Switch plate 2. Remove 2off pozi head screw (M3x16) and remove the switch. When replacing the switch, ensure that the wires are fitted to the correct terminals. Pozi head screw (M3x16) Microswitch 3.
6-2 Greasing the Pedal Assy Plunger 1. Remove 4off security screw (M5x12) and remove the switch cover plate. Security screw (M5x12) Switch plate 2. Remove 2off whizztite nuts (M4) and remove the switch. 3. Remove 4off whizztite nuts (M4) and remove the plunger assembly. Note: The plunger is spring loaded. Keep the plunger pressed in when removing the assy and release the plunger slowly. 4. Remove any old grease and dirt from the plunger and pedal plate.
6-3 Replacing the Pedal Plunger 1. Remove the plunger assembly. (See 6-2 page 60) 2. Pull the plunger out of the holder. Replace with the new plunger. (The new plunger should have grease applied all over prior to fitting). Holder Plunger 3. Wipe off any old grease and dirt from the pedal plate and regrease. (see 6-2 page 65) 4. Reassemble in reverse order.
6-4 Removing the Play Panel 1. 2. Remove 6off security screw (M5x12). Lift the play Panel slightly and disconnect the connector. Security screw (M5x12) Play panel Connector Security screw (M5x12) 3. Remove the play Panel complete with Gun Assy. 4. Reassemble in reverse order.
6-5 Gun Assembly 6-5-1 Removing the Gun Assembly 1. Remove the Play Panel Assy. (see 6-4 page 67) 2. Remove 2off Whizz nut (M6) and remove the Gun assy from the Play Panel Play panel Connector Whizz nut (M6) Note: When replacing the gun assembly ensure that the earth wires are located on the studs before fitting and tightening the whizz nuts.
6-5-2 Removing the Gun Slides 1. Remove the Gun Assy. (see 6-5-1 page 68) 2. With the left side of the gun placed down, remove 4off socket cap screws (M3x10) and 1off button head screw (M4x25) and nut (M4) Nut (M4) Socket cap screw (M3x10) Gun slide L Button head screw (M4x25) Socket cap screw (M3x10) Gun slide R 3. Remove the Gun Slides. 4. Reassemble in reverse order.
6-5-3 Removing the Gun Covers 1. Remove the Gun Slides. (see 6-5-2 page 69) 2. With the left side of the gun placed down, remove 4off button head screw (M4x10), 1off button head screw (M4x25) and 1off socket cap screw (M3x10), taking care not to lose any of the nuts. Nut (M4) Button head screw (M4x20) Lens Gun side (L) Gun PCB Button head screw (M4x10) Gun side R Socket cap screw (M3x10) Button head screws (M4x10) 3. Remove the Gun Cover R, taking care that the lens does not fall out. 4.
6-5-4 Replacing the Solenoid 1. Remove the Gun Covers. (see 6-5-3 page 70) 2. Disconnect the Solenoid Connector. 3. Remove 1off flange screw (M3x10) and remove the Solenoid Bracket. 4. Remove 1off flange screw (M3x8) and detach the earth wire. 5. Loosen the nut (16mm) and pull out the Solenoid. 6. Remove 2off flange screws (M4x6) and detach the Slide Guide. 7. Pull out the Solenoid Plunger, taking care not to lose the Spring.
6-5-5 Replacing the Trigger Switch 1. Remove the Gun Covers. (see 6-5-3 page 70) 2. Remove the Fast-On terminals from the Microswitch. 3. Remove the Microswitch. Microswitch Fast-On terminals 4. Reassemble in reverse order.
6-5-6 Replacing the Flexible Gun Conduit 1 Remove the Gun Assy. (see 6-5-1 page 68) 2. Remove 2off security screw (M4x10) and remove the Connector Cover. 3. Remove the Gun Covers (see 6-5-3 page 70) 4. Detach the Solenoid Bracket, Solenoid Connectors and earth wire. 5. Disconnect the PCB connectors and detach the Fast-On connectors from the microswitch. 6. Remove 1off button head screw (M4x10) fixing the Conduit to the Gun Cover and detach the Conduit.
6-6 Replacing the Neon Tubes The Neon Tubes use high voltage. The game must be turned OFF and disconnected from the power before touching any Neon Parts 1. Remove the Play Panel. (See 6-4 page 67) 2. Remove 6off security screw (M5x12) and remove the Front Grille.
3. Remove 2off hex head screw (M5x20) and remove the Rear Cover. Hex head screw (M5x20) 4. Disconnect the connector from the Neon PCB.
5. Remove the Neon Tube. Note: Always grip the tube by the end caps, not the glass tube. Neon Tube 6. Reassemble in reverse order.
6-7 Replacing the CCD Camera 1. Remove the Play Panel. (See 6-4 page 67) 2. Remove 2off whizz nuts (M4) and Earth lead. 3. Disconnect the connector and remove the Camera Assy. Camera Assy Whizz nut (M4) Connectors 4. Remove the 2off pozi head screws (M2x20) and remove the CCD Camera. CCD camera (Note the direction) Pozi head screws (M2 x 30) Camera filter 5. Reassemble in reverse order. Note: Ensure that the Camera is replaced the correct way round, or the game will not function correctly.
6-8 Replacing the Sensor 1. Remove the Play Panel. (See 6-4 page 67) 2. Remove the CCD Camera Assy (see 6-7 page 77) 3. Remove 2off pozi head screws (M2.5x14), with flat and spring washers, and remove the Sensor. Camera unit Sensor (Note the direction) Pozi head screw (with flat and spring washers) (M2.5 x 14) 4. Reasemble in reverse order. Note: Ensure that the Sensor is replaced the correct way round, or a Sensor Warning Message will be displayed and the game will not function correctly.
6-9 Replacing the Header Tube and Starter 1. Remove 10off security screws (M5x12), and remove the Header Acrylic. Security screw (M5x12) Header Acrylic Starter Fluorescent Tube (40w) 2. Replace the Fluorescent Tube or Starter. Note: The fluorescent tube is fitted with a blue filter. Remove the filter and fit to the new fluorescent tube before refitting the tube to the Header Assy. 3. Replace the Starter. 4. Reassemble in reverse order.
7.
Item Description Part No Transformer - 18v @3A 67700015 Bridge Rectifier 71000040 Capacitor - 22,000μF / 25v 70200043 Cabinet Side Decal - Left 40000764 Cabinet Side Decal - Right 40000765 21 Fork Here Decal 40000072 36 Amplifier PCB Assy 37 SMPSU 200w 1149-010 40 Bass Loudspeaker - SWM 1034 X006-115 41 Bass Por t Tube 46000837 43 Game PCB Assy - Time Crisis 3 8 16 XVN-BASSAMP Page 81 XTC3-GAMEPCB
7-2 Projector Cabinet - Front Page 82
Item Description Part No Deluxe Projector Cabinet -Left 37100210 Deluxe Projector Cabinet -Right 37100211 2 Thomson 46" 46JH68US Projection Monitor 84000052 3 Projector Cabinet Front Panel 37000073 Bass Speaker Wood - Left 37000078 Bass speaker Wood - Right 37000079 Internal Joint Suppor t - Left 47000686 Internal Joint Suppor t - Right 47000687 17 Sub Bass Speaker Grille 46000828 18 Marquee Bracket Locating Bracket 47000628 19 Header Locating Bracket 47000689 Cabinet Front Dec
7-3 Coin Tower Assy Item Description Part No 1 Gun Console Lower Cross Member 47000696 2 Gun Console Upper Cross Member 47000697 3 Coin Tower Metalwork 47000695 4 Pedal Fixing Bracket - A 47000698 5 Pedal Fixing Bracket - B 47000699 6 Coin Tower Instruction Panel 39000109 7 Instruction Decal 40000752 8 Instruction Metal 47000700 9 Adjustable Foot (M16 x 95) 88300079 10 Swivel Castor (38mm) 59000003 11 Credit Available When Lit Push Button 60200215 Page 84
7-4 Gun Tower Assy Item Description Part No Gun Suppor t Metal Section - Left 47000730 Gun Suppor t Metal Section - Right 47000731 Holster Metal Work- Red 47000703 Holster Metal Work- Blue 47000711 3 Gun suppor t Mesh 47000704 4 Holster Panel 47000705 5 Stainless Steel Fluorescent Bracket 47000706 Gun Console Left Decal 40000753 Gun Console Right Decal 40000754 7 P/Blank Gun Hoop for P/Panel 45000210 8 Camera/Sensor Clear Cover 39000110 13 Light Sensitivity Warning Label 41
7-5 CCD Camera and Sensor Item Description Camera Assembly Part No XTC3-CAMERAASSY 1 Camera/Sensor Enclosure 47000729 2 Camera Filter XCZ-694-832 3 CCD Camera XTC3CAM-CAMERA 4 Proximity Sensor 47000010 Proximity Sensor Cable Assembly 47000011 Page 86
7-6 Joint box Item Description Part No 1 Joint Box 47000728 2 Joint Box Cover Plate 47000708 3 Rays PCB XTC3CAM-RAYSPCB 4 Repeater PCB Assy XTC3-REPEATERPCB Page 87
7-7 Gun Assembly Page 88
Item 1 2 Description Par t No Gun Assembly - Red XTC3CAM-REDGUN Gun Assembly -Blue XTC3CAM-BLUEGUN Gun Cover (LHS) - Red XPB-Cover-LR Gun Cover (LHS) - Blue XPB-Cover -LB Trigger Spring XPB-296-421 Trigger - Red XPB-Trigger-R Trigger - Blue XPB-Trigger-B 4 Solenoid - ST-0860A2 XPB-004-056 5 Tube Bracket (A) XPB-296-418 6 Gun Cord Harness Assy XPB-296-401 7 Tube Bracket (B) XPB-296-423 8 Connector Cover XPB-296-424 3 9 10 Gun Cover (RHS) - Red XPB-Cover-RR Gun Cover (RHS
7-8 Pedal Assembly Item Description Part No 1 Pedal Assy - Black XTC3-PEDALBLACK 4 Spring (A) XTC-631-221 5 Spring Cover XTC-631-218 7 Rubber Stopper XTC-631-217 8 Plunger XTC-631-319 10 Spring (B) XTC-631-222 12 Microswitch - KSL 13 XTC 000-027 Page 90
7-9 Coin Door Assembly 1 2 3 Item 1 Description DFMD Black Leatherette W/O Cash Door Mars Cashflow 116DFx Front Entr y 2 3 Part No 53100029 65500757A Cashflow C (Front Entr y) Plate - 199245003 65100859 Mars Mech Front Panel 7809 Plastic 65100043 Mars Coin Catcher 28-13-0136 65100049 Quadriboss 4 Player 81000105 Securdor w/Lock Black Leatherette 53100322 Page 91
7-10 Service Bracket Assy Item Description Part No Panel Mount Fuseholder - 20mm 63500786 Fuse 2A Q/B - 20mm 63500501 2 Miniature Slide Switch 60000023 3 Push Button Switch 7mm - Red 60000059 4 SPDT Toggle Switch - (momentar y action) 60000010 5 Meter - Panel Mount 65000002 1
7-11 Header Assembly Item Description Part No 1 Header Front Metalwork 47000691 2 Header Main Metalwork 47000692 3 Spacer 47000694 4 Header Acr ylic 30000081 5 Fluorescent Tube 4ft 64000045 6 Fluorescent Blue Filter 47000684 7 Star ter 63000000
7-12 Mains-In Assy Item Description Part No 1 Schaffner Mains-In Filter 62500010 2 Schaffner Boot 66000017 Parts not Shown Interlock Switch 60000006 Interlock Switch Bracket 20000179 Interlock Switch Cover 39000028 Page 94
Copies of Namco Game Manuals can be downloaded from our website: www.namco.co.uk under Components Distribution For all Parts or Technical Support contact: Brent Electronic, Namco House, Units 7-8, Acton Park Estate, The Vale, London. W3 7QE www.brentelectronic.co.
