TOKYO WARS SD Operators Manual IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY. Part No.
PORTABLE APPLIANCE TESTING Please Note: During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between live / earth and neutral / earth. These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations. To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first.
GB No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from NAMCO EUROPE LIMITED. While the information contained in this manual is given in good faith and was accurate at the time of printing. NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
NOTES ON INSTALLATION NEVER turn the power to the machine ON until installation has been completed. In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug. In order to avoid damage to the machine due to mis-operation, ensure that the voltage of the mains supply is 230volts AC.
D Dieses Dokument darf in keiner Weise vervielfältigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datenträger (Suchsysteme), die Weitergabe oder sonstiges Kopieren für den gewerblichen und privaten Gebrauch sind untersagt und bedürfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED. Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behält sich jedoch das Recht zu Änderungen ohne vorherige Bekanntgabe vor.
HINWEISE ZUR AUFSTELLUNG NIEMALS das Gerät einschalten bevor die Aufstellung völlig abgeschlossen ist. Zur Vermeidung von Elektroschlägen muß das Gerät mit einem ordnungsgemäß geerdetem Netzstecker an die Stromversorgung angeschlossen werden. Zur Vermeidung von Beschädigungen durch Fehlbetrieb am Gerät sicherstellen, daß die Netzspannung 230 Volt beträgt.
F Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d’enregistement phonographique. Ces informations ne seront ni stockées grâce à un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l’autorisation de NAMCO EUROPE LIMITED.
NOTES D’INSTALLATION NE JAMAIS mettre le jeu en marche avant que l’installation ne soit complétement effectuée. Afin de prévenir une éventuelle électrocution, s’assurer que la machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité. Afin d’éviter que la machine ne soit abimée suite à une mauvaise opération, s’assurer que la tension sur le réseau principal soit de 230 volts AC.
I Nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza l’autorizzazione di NAMCO EUROPE LIMITED. Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione.
NOTES D’INSTALLATION NON ACCENDERE MAI la macchina finchè l’installazione non è stata completata. Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure. Per evitare danni alla macchina durante la messa in opera, assicurarsi che il voltaggio della rete sia 230 volts AC.
SF Tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman NAMCO EUROPE LIMITED:in lupaa. Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. NAMCO EUROPE LIMITED:illä on kuitenkin oikeus muutoksiin ilman erillistä ilmoitusta. Tämä laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiivejä: 89/336/EEC ja 72/23/EEC (EN55014, EN55104 ja EN 60335-1 standardit).
ASENNUSHUOMIOITA Älä koskaan kytke laitetta päälle ennen kuin asennus on suoritettu loppuun. Tämän laitteen virtalähde on kytkettävä maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sähköiskun vaaraa ei olisi. Varmista, että virtalähteen jännite on 230V AC, jotta ei laite vioitu. Huomio: Jos tämä laite sijoitetaan liukkaalle esim, vahatulle lattialle, suositellaan laitettavaksi kumityynyt säätöjalkoihin liikkumisen estämiseksi.
Contents CERTIFICATE OF CONFORMITY ........................................................................ 2 PORTABLE APPLIANCE TESTING ...................................................................... 3 SAFETY WARNING .............................................................................................. 4 NOTES ON INSTALLATION ................................................................................. 4 MOVING THE MACHINE .................................................................
1. SPECIFICATIONS POWER SUPPLY:- 230volts AC AMBIENT OPERATING TEMPERATURE:+5°C to +25°C MONITOR:- Hantarex 28” Polo Monitor COIN ACCEPTOR:- Mars CashFlow - Dispense DIMENSIONS:Assembled Cabinet Seat Assy 1400(w) x 1650(d) x 2050(h) 1400(w) 490(w) x 930(d) x 820(d) x 2050(h) x 1330(h) WEIGHT:Assembled Cabinet Seat Assy ACCESSORIES:- 345kg 295kg 25kg Keys: (Cash Door) .................... 2 (Coin Door) ..................... 2 (Back Door) .................... 2ea IEC Mains Lead ............
2. HOW TO PLAY This game is a multi-player fighting game where one or two players join two armies to fight against the opposing army. By using the steering wheel and accelerator pedals, a player controls their tank and moves freely in the city limits in order to search out and attack the enemy. OPERATION 1) Stepping on the forward pedal (right pedal): Player’s tank moves forward. 2) Stepping on the backward pedal (left pedal): Player’s tank moves backwards.
3.
4. MOVING THE MACHINE MOVING THE MACHINE This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface. The overall height of the machine, with the Header Assembly fitted, is 2050mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.) 5. INSTALLATION NOTES ON INSTALLATION NEVER turn the power to the machine ON until installation has been completed.
쮕 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN GESCHLOSSENEN RÄUMEN BESTIMMT. DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN Im Freien. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an Plätzen mit extrem hohen oder niedrigen Temperaturen. In der Nähe von Notausgängen oder Feuerlöschgeräten.
5-1 Assembling the Machine 1. Remove the 16off (8 on each seat) Hex Head Screws (M10x25), Flat and Spring Washers and remove the Seat/Cabinet Joint Bracket from the Seat assembly. 2. Remove the 8off Hex Head Screws (M10x25), Flat and Spring Washers from the front of the Monitor Cabinet. 3. Place the Seat Assemblies close to the Monitor Cabinet and connect the connectors. 4.
6 ADJUSTMENTS 6-1 Turning on the Power After the machine has been installed, turn ON the power. The power switch is located on the rear of the cabinet. 6-2 Adjustment Switches The Adjustment switches are located inside the coin door 1. Service Switch Press the service switch to obtain game credits without incriminating the play meter. 2. Test Switch Slide the Test Switch ON to enter test mode. Test Mode allows the testing and changing of game settings.
6-3 Test Mode 1. Open the coin door and slide the test switch “on”. The menu screen will be displayed on the monitor. 2. Select the test required by turning the steering wheel left or right. The selected test will ‘blink’. 3. Enter the selected test by depressing the forward pedal (right pedal). Select “EXIT” to return to the “Menu Screen”. 4. After testing is completed, ensure that the test switch is returned to the “OFF” position to return to normal game mode.
6-3-1 1. 2. Coin Options Select item (1) "COIN OPTIONS" on the menu screen to set the game cost and related settings. Turn the steering wheel to select the required item. COIN OPTIONS [ DEFAULT IN GREEN ] GAME COST 1 COIN1 CREDIT FREE PLAY 3. 4. Use the 'Trigger' buttons to adjust the settings. ...................... (a) OFF ...................... (b) EXIT : PRESS VIEW CHANGE BUTTON Press ‘View Change’ Button to return to the menu screen.
6-3-2 Game Options 1. Select item (2) "GAME OPTIONS" on the menu screen to set the game options and related settings. 2. Turn the steering wheel to select the required item. 3. Press the 'Trigger' buttons to adjust the settings. Standard settings are displayed in green. 4. Press ‘View Change’ Button to return to the menu screen. GAME OPTIONS [ DEFAULT IN GREEN ] ID No.
6-3-3 Effect Test 1. Select item (3) "Effect Test" on the menu screen to test the lamps and drive output 2. Turn the steering wheel to select the required item. 3. Use the right Trigger Button to activate the test. 4. Press ‘View Change’ Button to return to the menu screen. EFFECT TEST LAMP HANDLE + SEAT HANDLE SEAT ............................ ............................ ............................ ............................
6-3-4 Switch Test 1. Select item (4) "Switch Test" on the menu screen to test the switches and Potentiometers 2. Turn the steering wheel to select the required item. 3. Use the right Trigger Button to activate the test. 4. Press ‘View Change and Right Trigger’ Buttons together to return to the menu screen. SWITCH TEST HANDLE RIGHT PEDAL LEFT PEDAL 0000 ................. (a) 0000 ................. (b) 0000 .................
6-3-5 Monitor Test 1. Select item (5) “MONITOR TEST” on the menu screen to set up and adjust the monitor. 2. On entering monitor test, the screen will display one of the following test patterns. GRADATION PATTERN CROSSHATCH CROSSHATCH WHITE WINDOW WHITE WINDOW WHITE WINDOW INTERLACE PATTERN VIEW ANGLE ADJUST VIEW ANGLE ADJUST FULL WHITE GREEN WHITE (H) (M) (L) (CRT) (PROJECTOR) 3.
4. Pressing the right trigger button will cause the selected value increase. 5. Pressing the left trigger button will cause the selected value to decrease. 6. Depressing the forward pedal (right pedal) will produce the sound of the song number selected. (Request Song 01 will produce a stereo sound test. Sound will be produced from the speakers in the following order:Left front speaker, Right front speaker, Both front speakers, seat speaker and finally the seat shaker will vibrate.) 7.
6-4 Initialization after Replacing Parts Initialization must be performed after replacing the Game PCB, ROMS, or Steering and Pedal Potentiometers. If initialization is not performed, the game will not function correctly. 1. Ensure that the steering wheel is in the centre position and that the pedals are fully up. 2. Slide the Test Switch into the ON position while pressing the service button. Keep the service button pressed until the “ADJUST MODE” screen is displayed. (This will take approx. 5 secs.
6-6 Linking Two Machines 1. Ensure that the power is OFF. 2. Loosen the two pozi head screws retaining the link cover bracket, located next to the mains-in socket on the rear of the machine, and remove the link cover bracket. 3. Use the supplied link cables to connect each link board. (See Diag.) ON INT ON ON INT ON OFF EXT OFF OFF EXT OFF IN OUT 4. Set the link switches to “ON”, “EXT” and “ON”. (Refer to 6-6-1 (below) “Setting the Link Switches”) 5.
7. MAINTENANCE In order to prevent injury or electric shock to service personnel, ensure that the MAIN POWER IS OFF before attempting any maintenance. Before performing any work not described in this manual, be sure to contact your distributor to receive instructions or answers to questions. 쮕 Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der Netzstecker gezogen werden.
7-1 Replacing the Fluorescent Tube, Starter and Lamps 1. Remove the four security screws (M4x16) and remove the glass retaining bracket. 2. Remove the four security screws (M4X20), from the top, and remove the header acrylic. 3. Replace the fluorescent tube or starter. 4. The lamps are a screw fitting. Turn anti-clockwise to remove. 5. Reassemble in reverse order. Warning The fluorescent tube may be hot. Take care when handling the tube.
7-2 Replacing the Viewpoint and Credit Available Switches 1. Remove the four security screws (M6x25) and washers from the top of the play panel and hinge the play panel forwards. 2. Remove the lamp/switch assembly by pulling it away from the switch body. Replace the switch or lamp. Note: When replacing the switch ensure that the wires are replaced to the correct terminals 7-3 Removing the Steering Wheel 1. Carefully remove the round hub cover by gently levering out using a flat blade screwdriver.
7-6 Removing the Pedal Assembly 1. Remove the four security screws (M6x25), flat and spring washers and withdraw the pedal assembly from the front of the machine. ( Take care not to strain the wires.) 2. Disconnect the connector and remove the assembly. 7-7 Replacing the Pedal Potentiometer 1. Remove the pedal assembly. (Refer to section 7-6, above.) 2. Loosen the grub screw and remove the gear. 3. Replace the potentiometer. 4.
8.
1 2 5 Item Description 3 4 Part No 1 Header Acrylic 30000233 2 Flurescent Tube 4ft 64500014 3 Starter 63000000 4 E14 Golfball Lamp - 240vAC/25watt 64000084 5 E14 Lamp Holder 64800003 Page 36
1 2 3 4 5 6 7 9 Item Description 8 Part No 1 Speaker Plate Black - LHS 88300603 2 Speaker Plate Black - RHS 88300604 3 Loudspeaker - 4‰" 20watt 62000006 4 Seat - Dark Blue 46000046 5 Decal - Seat Rear 40000376 6 Loudspeaker - Bass Shaker 62000076 7 Decal - Namco Base 40000036 8 M16 Adjustable Foot 88300079 9 Swivel Castor - 75mm 59000005 Page 37
9.
Page 39
Page 40
Page 41
