VAMPIRE NIGHT DX OPERATORS MANUAL IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY Part No.
Page 2
is a copyrighted anti-copying technology created by Sony Corp. This mark does not necessarily imply compatibility with other products bearing the MAGICGATE trademark. is a trademark of Sony Corporation. Le présent document vous informe que ce produit peut être soumis à la législation de contrôle des exportations nationales. Vous êtes tenu(e) en permanence de vous conformer entièrement aux exigences dune telle législation ainsi que de toute autre juridiction en relation avec ce produit.
Contents OPERATORS MANUAL ................................................................................................................1 GENERAL SAFETY CONSIDERATIONS .....................................................................................6 ALLGEMEINE SICHERHEITSHINWEISE ....................................................................................8 GENERELLE SIKKERHEDSOVERVEJELSER ..........................................................................
7. MAINTENANCE .....................................................................................................................59 7-1 Cleaning the Camera Window Covers ............................................................................61 7-2 Replacing the Fluorescent Tube or Starter ......................................................................62 7-3 Replacing the Camera Assy ...........................................................................................
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private use, without permission from NAMCO EUROPE LIMITED. While the information contained in this manual is given in good faith and was accurate at the time of printing, NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
NOTES ON INSTALLATION NEVER turn the power to the machine ON until installation has been completed. 2m10cm or more 50cm or more 50cm or more 50cm or more In order to prevent possible electric shocks, be sure that the equipment is connected to the mains with a securely connected earthed plug. 2m90cm or more So that customers are not injured by the movement of the equipment, ensure that there is at least 500mm seperation between other equipment or walls.
D Dieses Dokument darf in keiner Weise vervielfältigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datenträger (Suchsysteme), die Weitergabe oder sonstiges Kopieren für den gewerblichen und privaten Gebrauch sind untersagt und bedürfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED. Die Informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behält sich jedoch das Recht zu Änderungen ohne vorherige Bekanntgabe vor.
HINWEISE ZUR AUFSTELLUNG 2m10cm or more 50cm or more 50cm or more 50cm or more NIEMALS das Gerät einschalten bevor die Aufstellung völlig abgeschlossen ist. 2m90cm or more Zur Vermeidung von Elektroschocks muß das Gerät mit einem ordnungsgemäß geerdetem Netzstecker an die Stromversorgung angeschlossen werden.
Denne udgivelse må ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den må heller ikke lagres i et eftersøgningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra Namco Europe Limited. Da informationerne i denne manual er givet med god tro og var korrekt på udskivningstidspunktet, forbeholder Namco Europe Limited sig retten til, at foretage ændringer og forandringer uden varsel.
PUNKTER OM INSTALLATION Tænd aldrig for strømmen til maskinen før installering er fuldført. 2m10cm or more 50cm or more 50cm or more 50cm or more For at undgå mulige elektriske stød sikres, at maskinen er forbundet til hovedstrømmen med sikkert monterede jordstik. 2m90cm or more For at kunder ikke kommer til skade ved spillets bevægelser sikres, at der er mindst 50cm afstand til andre maskiner og vægge.
No se permite la reproducción total ni parcial de esta publicación por ningún medio mecánico, fotográfico o electrónico, grabaciones fonográficas, ni su almacenamiento informático, su transmisión o su copia, ya sea para uso público o privado, sin permiso de NAMCO EUROPE LIMITED. Si bien la información contenida en este manual se da de buena fe y es correcta en el momento de su impresión, NAMCO EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.
NOTAS DE INSTALACIÓN. 2m10cm or more 50cm or more 50cm or more 50cm or more JAMÁS ENCIENDA la máquina antes de haber completado la instalación. Para evitar posibles descargas eléctricas, asegúrese de que la máquina está conectada a la red con un enchufe provisto de toma de tierra. 2m90cm or more Para que los usuarios no sufran lesiones debido al movimiento del juego, asegúrese de que hay al menos 500 mm de separación entre éste y otras máquinas o las paredes.
Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen denregistement phonographique. Ces informations ne seront ni stockées grâce à un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans lautorisation de NAMCO EUROPE LIMITED.
NOTES DINSTALLATION 2m10cm or more 50cm or more 50cm or more 50cm or more NE JAMAIS mettre le jeu en marche avant que linstallation ne soit complétement effectuée. 2m90cm or more Afin de prévenir une éventuelle électrocution, sassurer que la machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité.
ও Κανένα μέρος αυτής της έκδοσης δεν μπορεί να αναπαραχθεί με οποιοδήποτε μηχανικ" ,φωτογραφικ" ή ηλεκτρονικ" μέσο , ή με μορφή φωνητικής ηχογράφησης και ούτε να αποθηκευτεί με επανορθωτικ" σύστημα , να μεταδοθεί ή να αντιγραφεί για δημ"σια ή ιδιωτική χρήση , χωρίς την άδεια της NAMCO EUROPE LIMITED. Καθώς αυτές οι πληροφορίες σε αυτ" το εγχειρίδιο έχουν δοθεί με καλή πίστη και ακριβώς την ώρα της τύπωσης , η εταιρεία NAMCO EUROPE LIMITED κρατάει το δικαίωμα να κάνει οποιεσδήποτε αλλαγές χωρίς ειδοποίηση.
ΣΗΜΕΙΩΣΕΙΣ ΓΙΑ ΤΗΝ ΕΓΚΑΤΑΣΤΑΣΗ 2m10cm or more 50cm or more 50cm or more 50cm or more ΠΟΤΕ να μην αν%βει το μηχ%νημα ε%ν δεν χει ολοκληρωθε η εγκατ%σταση. 2m90cm or more Για την αποφυγ# ηλεκτρικ)ν σοκ πρ πει το μηχ%νημα να χει γειωθε . Για την αποφυγ# κινδ νου σε κ%ποιον πα κτη , πρ πει το μηχ%νημα να χει απ σταση τουλ%χιστον 500MM απ %λλο μηχ%νημα # το χο.
Nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza lautorizzazione di NAMCO EUROPE LIMITED. Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione.
NOTES DINSTALLATION NON ACCENDERE MAI la macchina finchè linstallazione non è stata completata. 2m10cm or more 50cm or more 50cm or more 2m90cm or more 50cm or more Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure. Perchè i clienti non siano feriti dal movimento del gioco, assicurarsi che ci siano almeno 500mm di distanza rispetto alle altre macchine o rispetto al muro.
Ingen del av denne utgivelsen må reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra NAMCO EUROPE LIMITED. Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP LIMITED seg retten til å lage forandringer uten varsel.
MERKNADER VED INSTALLASJON 2m10cm or more 50cm or more 50cm or more 50cm or more Slå ALDRI på maskinens strømforsyning før installasjonen er fullført. For å forhindre eventuelle elektriske sjokk, forsikre deg om at maskinen er koplet til et strømnett med ordentlig jording. 2m90cm or more For å forhindre at kundene blir skadet av spillets bevegelige deler. forsikre deg om at det er minst 500mm avstand mellom andre maskiner eller vegger.
Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe Limited.
Opmerkingen aangaande Installatie 2m10cm or more 50cm or more 50cm or more 50cm or more Sluit de machine nooit aan op de stroomtoevoer totdat de installatie is voltooid. 2m90cm or more Om mogelijke electrische schokken te voorkomen, dient ervoor gezorgd te worden dat de machine middels een goed vastzittende aardstekker op het lichtnet is aangesloten.
Nenhuma parte desta publicacão poderá ser reproduzida por processos mecanográficos, fotográficos, electrónicos ou ainda sob a forma de gravacão sonora nem tão pouco poderá ser gravada através de sistemas informáticos transmissiveis ou de outra forma copiados para uso publico ou privado sem autorização expressa da NAMCO EUROPA LIMITADA. A informação contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicação.
NOTAS SOBRE A INSTALAÇÃO NUNCA ligar a maquina sem que a instalação esteja completamente finalizada. 2m10cm or more 50cm or more 50cm or more 50cm or more Afim de evitar possiveis choques electricos, certifique-se que a maquina está ligada à rede de alimentação com uma ficha protegida com circuito de terra. 2m90cm or more Afim de evitar ferimentos pessoais nos clientes, provocados pelo movimento da maquina, certifique-se que existe pelo menos 500mm de separação entre outras maquinas ou paredes.
Ingen del av denna publikation får reproduceras, varken fotografiskt, elektroniskt eller i någon form av ljudinspelning. Det får inte heller lagras i något återvinningssystem, översändas eller på annat sätt kopieras för offentlig eller privat användning, utan tillstånd från NAMCO EUROPE LIMITED. Eftersom informationen i denna manual lämnas ut i god tro och var korrekt när den trycktes, reserverar sig NAMCO EUROPE LIMITED för ändringar.
ATT BEAKTA VID INSTALLATION Sätt aldrig på strömmen på maskinen innan installationen är klar. 2m10cm or more 50cm or more 50cm or more 50cm or more För att förhindra elektriska chocker, försäkra dig om att maskinen kopplas till strömförsörjning med jordad kontakt 2m90cm or more För att undvika skador av spelets rörelser, försäkra dig om att det finns ett avstånd på minst 500 mm till annan maskin eller vägg.
Tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman NAMCO EUROPE LIMITED:in lupaa. Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. NAMCO EUROPE LIMITED:illä on kuitenkin oikeus muutoksiin ilman erillistä ilmoitusta. Tämä laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiivejä: 89/336/EEC ja 72/23/EEC (EN55014, EN55104 ja EN 60335-2-82 standardit).
ASENNUSHUOMIOITA 2m10cm or more 50cm or more 50cm or more 50cm or more Älä koskaan kytke laitetta päälle ennen kuin asennus on suoritettu loppuun. 2m90cm or more Tämän laitteen virtalähde on kytkettävä maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sähköiskun vaaraa ei olisi. PLAYZONE 50cm or more PATHWAY 1m or more Varmista, että laitteen ja seinän tai toisen laitteen välissä on vähintään 500 mm, jotta asiakkaat eivät loukkaannu laitteen likkumisesta johtuen.
1. SPECIFICATIONS POWER SUPPLY:- 230v /390watts AC AMBIENT OPERATING TEMPERATURE +5°C to +25°C MONITOR:- Thomson 46 Projection Monitor COIN ACCEPTOR:- Mars CashFlow - 1 Channel DIMENSIONS:Assembled Monitor Cabinet Gun Assy Header Assy WEIGHT:- 1116(w) x 1840(d) x 2230(h) 1116(w) x 800(d) 800(w) x 1040(d) 1080(w) x 610(d) x 1840(h) x 1200(h) x 530(h) Assembled 220kg Monitor Cabinet Gun Assy Header Assy 154kg 42kg 24kg ACCESSORIES:- Keys: (Cash Door) ............... 2 (Coin Door) ........
2. HOW TO PLAY This product is a gun shooting game for one or two players. Insert the specified number of coins to obtain the required credits. After establishing credits, press the Start button to start the game. When the game starts, shoot the enemies that appear on the screen. The players gun can shoot up to eight rounds in succession. When the gun is out of ammunition, point the gun away from the screen to reload.
3.
4. MOVING THE MACHINE This equipment is fitted with castors to make it easier to move. Take care when moving the equipment on an inclined floor. The overall height of this equipment is 2230mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.) 5. INSTALLATION Notes on Installation WARNING NEVER turn the power to the machine ON until installation has been completed.
1. 2. 3. 4. 5. 6. 쮕 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. This machine is designed for INDOOR USE ONLY. Do not install in the following places. Outdoors Direct Sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature. Places where it would be in the way of emergency exits or fire extinguishing equipment. Unstable places or places with excessive vibration.
1. 2. 3. 4. 5. 6. ও 1. 2. 3. 4 5. 6. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS A lextérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits où il y a des risques de fuite deau, près de ventilateurs ou source de chaleur, aux endroits très chauds ou froids.
1. 2. 3. 4. 5. 6. 1. 2. 4. 5. 6. 3. 4. 5. 6. 3. 4. 5. 6. ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS INTERIORES APENAS NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:- DENNA MASKIN ÄR AVSEDD ENBART FÖR INOMHUSBRUK INSTALLERA EJ MASKINEN PÅ FÖLJANDE STÄLLEN Utomhus I direkt solsken, platser med extremt hög luftfuktighet eller damm, platser där det förekommer vattenläckage, nära luftkonditionering eller värmeelement, i extremt hög eller låg temperatur.
5-1 Removing the Header Assy The Header assy has a forward centre of gravity, so it is important that at least two (2) people are used to fit or remove the Header assy. The fitting position of the Header assy is high, and it is important that a means of reaching the height safely, without stretching, is available, (e.g. steps, step stool, etc.). 1. Place the Header Assy on to the top of the Monitor Cabinet, and connect the connector. 2.
5-2 Fitting the Gun Cabinet to the Monitor Cabinet 1. Remove 4off hex head screws (M8x30) and remove the Joint Brackets from their shipping position. Refit the Joint Brackets as shown below with the 4off hex head screws (M8x30). Gun cabinet Joint bracket Hex head screws (M8x30) 2. Place the Gun Cabinet close to the Monitor Cabinet and connect the connectors. 3.
5-3 Adjusting the Level Adjusters 1. When the game is in its final position, lower the four (4) Level adjusters on the Monitor Cabinet, with a spanner, so that all castors are raised from the floor by approximately 5mm. Tighten the lock nuts with a spanner to ensure that the Level Adjusters do not move. Approx.
5-3 Fitting the CD Rom The supplied CD-ROMs are designed for this game only. Do not use them with other games. Do not insert any other CD-ROMs. These may result in malfunction. Always install one CD-ROM to each Game PCB Assy. Note that the tray automatically closes after approximately 10 seconds. 1. Remove the Lower Rear Door from the Monitor Cabinet. 2. Press the EJECT button on the CD-ROM drive to open the tray. CD-ROM tray Operating lamp EJECT button Game PCB Assy 3.
6 ADJUSTMENTS Adjustment or maintenance on this machine should be carried out by qualified personnel only. Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem Fachpersonal vorgenommen werden. Justeringer eller vedligehold af denne maskine bør kun udføres af kvalificeret personale. Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo por personal cualificado.
6-1 Adjustment Switches The Adjustment switches are located inside the coin door. 1. Service Switch. Press this switch to obtain game credits without incrementing the play meter. 2. Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-2 "Test Mode" page 43) 3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode. 4.
6-2 Test Mode 1. Open the coin door and slide the test switch ON. The Menu Screen will be displayed on the monitor. 2. Use the Select Up / Down switch to step through the tests. 3. Activate the required test by pressing the Enter button. Select EXIT in each test to return to the Menu Screen. 4. After testing is completed, slide the test switch to the OFF position to return to normal game mode. The Test Switch must always be in the OFF position for normal game mode.
6-2-1 Coin Options 1. Select COIN OPTIONS on the menu screen to set the game cost and related settings. The following screen is displayed. 2. Use the Select Up/Down switch choose the required item then press the Enter button. 3. Use the Select Up/Down switch to change the setting. 4. Select EXIT and press the Enter button to return to the menu screen. Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Game Cost is set to 1 Coin 1 Credit.
6-2-2 Game Options 1. Select GAME OPTIONS on the menu screen to set the game settings. The following screen is displayed. 2. Use the Select Up/Down switch choose the required item then press the Enter button. 3. Use the Select Up/Down switch to change the setting. 4. Select EXIT and press the Enter button to return to the menu screen.
6-2-3 I/O Test 1. Select I/O TEST on the menu screen to initialize the guns and to test switches and sensor. The following screen is displayed. 2. Use the Select Up/Down switch choose the required item then press the Enter button. 3. Use the Select Up/Down switch to change the setting. 4. Select EXIT and press the Enter button to return to the menu screen.
6-2-3-1 Gun Initialize 1. Select GUN INITIALIZE on the I/O Test screen. The following screen is displayed. GUN INITIALIZE ( a) +OUT + OF SCREEN 1P +OUT + OF SCREEN 2P (b) (1P SIGHT MARK) This mark moves around the screen as the 1P gun is moved AIM AT SCREEN TO CHECK GUN ACCURACY (2P SIGHT MARK) This mark moves around the screen as the 2P gun is moved PUSH SERVICE SW :ADJUST GUN SIGHT ENTER SW :ENTER The 1P and 2P gun sights can be checked using the screen above.
If the Service switch is pressed when in the Gun Initialize screen, the following screen is displayed. 1P GUN INITIALIZE AIM AT CENTRE OF THE CROSS AND PULL 1P GUN TRIGGER Aim the 1P gun at the cross in the centre of the screen and pull the trigger. The following screen will be displayed. 1P GUN INITIALIZE AIM AT CENTRE OF THE CROSS AND PULL 1P GUN TRIGGER Aim the 1P gun at the cross in the top left of the screen and pull the trigger. The following screen will be displayed.
1P GUN INITIALIZE AIM AT CENTRE OF THE CROSS AND PULL 1P GUN TRIGGER Aim the 1P gun at the cross in the top right of the screen and pull the trigger. The following screen will be displayed. 1P GUN INITIALIZE AIM AT CENTRE OF THE CROSS AND PULL 1P GUN TRIGGER Aim the 1P gun at the cross in the bottom right of the screen and pull the trigger. The following screen will be displayed.
1P GUN INITIALIZE AIM AT CENTRE OF THE CROSS AND PULL 1P GUN TRIGGER Aim the 1P gun at the cross in the bottom left of the screen and pull the trigger. The screen will revert to showing a cross in the centre of screen. Repeat the above procedures with the 2P gun. When the 2P gun has been aimed and fired on the screen above, the screen will display the GUN INITIALIZE screen. Recheck that both guns are aiming correctly.
6-2-3-2 Switch Test 1. Select SWITCH TEST on the I/O Test screen to test the switches and sensor. The following screen is displayed. I/O TEST SWITCH TEST COIN SERVICE TEST UP SELECT DOWN SELECT ENTER START 1P BUTTON START 2P BUTTON GUN 1P TRIGGER GUN 2P TRIGGER SENSOR 000 OFF ON OFF OFF OFF OFF OFF OFF OFF OFF UP SELECT SW+ENTER SW:EXIT Each time a coin is entered the COIN numbers will increase by one.
6-2-4 Monitor Test 1. Select MONITOR TEST on the Menu screen to check and adjust the monitor. The following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Press the Enter button to exit each test. 4. Select EXIT and press the Enter button to return to the menu screen.
6-2-5 Sound Test 1. Select Sound Test on the Menu screen to check and adjust the sound. The following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Use the Select Up/Down switch to change the setting then press the Enter button to return to item select. 4. Select EXIT and press the Enter button to return to the menu screen. SOUND TEST [DEFAULT IN GREEN] VOLUME ALL SP [0∼64] 14 ATTRACT [0∼64] 14 REQUEST BGM NO. 000 SE NO.
6-2-6 ADS Data (Book Keeping) 1. Select ADS DATA on the Menu screen to check all the book keeping data. The following screen is displayed. 2. Use the Select Up/Down switch to choose the required item then press the Enter button. 3. Press the Enter button to exit each page and return to this ADS Menu screen. 4. Select EXIT and press the Enter button to return to the menu screen.
6-2-6-1 Game Report 1. Select GAME REPORT on the ADS DATA Menu screen to check game reports. The following screen is displayed. 2. Press the Enter button to exit this page and return to ADS Menu screen.
6-2-6-2 Game Histogram 1. Select HISTOGRAM on the ADS DATA Menu screen to check game reports. The following screen is displayed. 2. Press the Enter button to exit this page and return to ADS Menu screen.
6-2-6-3 ADS Initialize 1. Select ADS INITIALIZE on the ADS DATA Menu screen to check game reports. The following screen is displayed. 2. Use the Select Up/Down switch to select either NO (no reset) or YES (data reset) then press the Enter button. 3. Select EXIT and press the Enter button to return to the menu screen.
6-2-7 Others 1. Select OTHERS on the ADS DATA Menu screen to set all adjustments to factory defaults. The following screen is displayed. 2. Use the Select Up/Down switch to select either NO (no reset) or YES (reset data to factory settings) then press the Enter button. 3. Select EXIT and press the Enter button to return to the menu screen. OTHERS ROM1 Ver .00/12/09 SAT 02:27:14 CLOCK .
7. MAINTENANCE Adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the POWER to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, service or repairs etc.) Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem Fachpersonal vorgenommen werden. Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der Netzstecker gezogen werden.
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine UITgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.) Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente por pessoal qualificado. Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutenção. (identifação de avarias, reparação etc.
7-1 Cleaning the Camera Window Covers To ensure gun accuracy, clean the windows of the camera daily with a soft cloth. If the windows are scratched or damaged, the gun sensor detection may not operate correctly.
7-2 Replacing the Fluorescent Tube or Starter 1. Remove 3off security screw (M5x12) and remove the Retaining bracket. 2. Remove the Header Acrylic Security screw (M5x12) Retaining bracket Header Acrylic Header Vac-form 3. Replace the Fluorescent Tube or Starter. 4. Reassemble in reverse order.
7-3 Replacing the Camera Assy 1. Remove 2off security screws (M5x12), disconnect the connectors and remove the Camera assy. Security screw (M5x12) Connectors 2. Camera Assy Remove 2off Whizz nuts (M4) and remove the Camera Mounting bracket. Whizz nut (M4) Earth connector Camera mounting bracket 3. Remove 2off pozi head screw (M2x30), Camera Filter (note which way round this filter is facing), 2off Spacers and the Camera PCB.
7-4 Replacing the Sensor 1. Remove the Camera assy. (see 7-3 page 63) 2. Remove 2off pozi head screws (M2.5x14), with flat and spring washers, and remove the Sensor. Camera unit Interruption sensor (note direction) Pozi head screw (M2.5 × 14) (with flat and spring washers) 3. Note: Reassemble in reverse order. Check the direction of the interruption sensor when reinstalling. If the sensor is installed facing the wrong way, a message will appear on the screen and the game cannot start.
7-5 Removing the Switch Panel Assy 1. Remove 6off button head screw (M6x12) and lift the Switch Panel Assy. Button head screw (M6x12) Switch panel Play panel 2. Disconnect the connectors and remove the Switch Panel Assy. Earth Terminals Play Panel Connector Connectors 3. Reassemble in reverse order.
7-6 Replacing the Start Switches 1. Remove the Switch Panel Assy. (see 7-5 page 65) 2. Remove the Switch Assy by pulling it out of the Switch Body. Play Panel Assy 1P Start Switch Assy Violet N.O COM Black 2P Start Fast-On terminals Switch Assy Whi/Vio N.O COM Black Fast-On terminals 3. Replace the Switch. When replacing the switch, note which wires are on which terminals. 4. Refit the Switch Assy to the Switch Body by pushing the Switch Assy fully into the Switch Body.
7-7 Replacing the Gun Assemblies 1. Remove the Switch Panel Assy. (See 7-5 page 65) 2. Disconnect the connector. 3. Remove 2off Whizz nut (M4) and remove the Rope Hoop. 4. Remove 2off Whizz nut (M6) and remove the Gun Assy. Gun Assy Connector cover Assy Rope hoop Gun bracket support plate Whizz nut (M6) Whizz nut (M4) Connector Underside of Play Panel Assy 5. Reassemble in reverse order. Note: Always reinitialize the guns if the guns has been removed or replaced.
7-7-1 Removing the Gun Covers 1. Remove the Switch Panel Assy. (See 7-5 page 65) 2. Remove the Gun Assembly. (See 7-7 page 67) 3. Remove 1off socket head screw (M4x25) and 1off dome head nut (M4). 4. Remove 2off socket cap screws (M3x10) and remove the Gun Cover (R) 5. Remove 2off socket cap screws (M3x10) and remove the Gun Cover (L) Dome nut (M4) Socket cap screw (M3x10) Gun cover (L) Socket head screw (M4x25) Socket cap screw (M3x10) 6. Note: Gun cover (R) Reassemble in reverse order.
7-7-2 Separating the Gun Body 1. Remove the Switch Panel Assy. (See 7-5 page 65) 2. Remove the Gun Assembly. (See 7-7 page 67) 3. Remove the Gun Covers (See 7-7-1 page 68) 4. Remove 4off socket head screw (M4x10), 4off dome nut (M4). 1off socket head screw (M4x25), 1off socket cap screw (M3x10) and remove the Gun Body (R).
7-7-3 Replacing the Trigger Switch 1. Remove the Switch Panel Assy. (see 7-5 page 65) 2. Remove the Gun Assembly. (See 7-7 page 67) 3. Remove the Gun Covers (See 7-7-1 page 68) 4. Seperate the Gun Body. (See 7-7-2 page 69) 5. Replace the Trigger Microswitch. Trigger switch (Yellow) N.O. terminal (Black) COM. terminal 6. Reassemble in reverse order. Note: Ensure that the correct wires are fitted to the correct switch terminals when refitting the Trigger Microswitch.
7-7-4 Replacing the Gun Cable 1. Remove the Switch Panel Assy. (See 7-5 page 65) 2. Remove the Gun Assembly. (See 7-7 page 67) 3. Remove the Gun Covers (See 7-7-1 page 68) 4. Seperate the Gun Body. (See 7-7-2 page 69) 5. Remove 2off socket head screw (M4x10) and remove the Connector Cover. 6. Disconnect the terminals from the Trigger Switch. 7. Disconnect the Gun PCB connector. 8. Remove 1off socket head screw (M4x10) and remove the Gun Cable.
7-7 Replacing the RAYS PCB 1. Remove 4off button head screws (M6x25) and remove the Maintenance Cover. Button head screws (M6x25) Flat washer Flat washer Maintenance cover Gun stand Assy 2. Remove 2off button head screws (M5x10) and remove the Rays Cover. Button head screws (M5x10) RAYS cover Gun stand Assy 3. Disconnect the connectors (x6) and remove the RAYS R PCB. Cap screws (M) (M3 × 6) RAYS-R PC board Connectors (×6) 4. Reassemble in reverse order.
Page 73
8.
Item Description Par t No 1 Side Decal (RHS) 40000654 2 Side Decal (LHS) 40000653 3 Front Decal 40000655 5 Header Retainiong Bracket 47000460 6 'Fork Here' Decal 40000072 7 Adjustable Foot- M16x95 88300079 8 Swivel Castor - 75mm 59000005 9 Thompson ON/OFF Switch Cover 47000477 11 Game PCB Assy XVN-GAMEPCB 12 Bass Amp PCB Assy XVN-BASSAMP 13 Switchmode Power Supply 1149-010 14 12vDC Power Supply 83000019 15 RCA Harness 69200001 16 USB-A-XH Internal Link Cable 17 J
8-2 Service Bracket and Mains-In Assembly 1 8 9 2 5 7 4 6 3 Item 1 Description Par t no 3.
8-3 Gun Cabinet 9 5 3 6 11 10 8 Item Description Par t No 3 Gun Cabinet Wooden Closing Plate 37000063 5 Rays PCB Cover 47000464 6 Joint Bracket Internal Suppor t Bracket 47000392 8 Fixed Castor - 50mm 59000009 9 Rays-R PCB 10 Bass Loudspeaker - Phillips Type P15 EN79-54F X006-140 11 Bass Speaker Por t 46000837 XVN-RAYSPCB Page 77
8-4 Camera Assy 2 3 4 Item 3 Description Par t no 1 Camera Assy DX XCZ-DX-CAMERA 2 Camera/Sensor Cover Plate 47000465 3 Camera Por t Cover 39000060 4 Motion Sensor 47000010 Page 78
8-5 Play Panel Assy 1 5 CAUTION 9 2 7 3 Item 6 8 Description Par t no 1 Instruction Decal Round 40000656 2 Gun Holster - Red 47000466 3 Gun Bracket Suppor t Plate 47000405 5 Play Panel Vac-Form 47000454 6 Switch Decal 40000659 7 Play Panel Decal 40000658 8 Triangular Star t Button Assy - Blue 60500005 9 Gun Holster - Blue 47000478 Page 79
8-6 Gun Assembly 1 4 5 2 9 7 11 6 3 12 8 10 13 Page 80
Item Description Par t no 1 Slide Bracket XVN-702-190 2 Gun Cover (L) 3 Gun Cover (R) 4 Gun Slide (L) 5 Gun Slide (R) 6 Trigger XPB-296-415 7 Trigger Spring XPB-296-421 8 Connector Cover XVN-701-906 9 Lens XPB-296-466 10 Gun Tube (Exp) XVN-702-191 11 NF-GUN (DX) PCB 12 Microswitch 13 Gun Assembly - Complete Set of both items XVN-296-407 Set of both items XVN-296-408 XVN-GUNPCB XPB-000228 XVN-DX-GUN Par ts Not Shown StrainRelief Rope 45000708 Gun/Rope Clamps 4500021
8-7 Header Assembly 5 10 11 1 12 7 (Opposite side 6 ) 4 Item 2 9 Description Par t no 1 Header Acrylic 30000071 2 Speaker Grille 47000472 4 Header Vac-Form 47000471 5 Acrylic Upper Retaining Bracket 47000473 6 Header Vac-Form Fixing BRacket (LHS) 47000474 7 Header Vac-Form Fixing Bracket (RHS) 47000475 9 Speaker - 4½" 62000006 10 Fluorescent Fitting (complete) 3ft 64500040 11 Fluorescent Tube 3ft 64500013 12 Star ter 63000000 Page 82
9.
Copies of Namco Game Manuals can be downloaded from our website: www.namco.co.uk under Components Distribution For all Parts or Technical Support contact: Brent Electronic, Namco House, Units 5-8, Acton Park Estate, The Vale, London. W3 7QE www.namco.co.
