OPERATORS MANUAL IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY Part No: 90500159 Issue 2
Contents GENERAL SAFETY CONSIDERATIONS ................................................................................4 ALLGEMEINE SICHERHEITSHINWEISE ...............................................................................6 GENERELLE SIKKERHEDSOVERVEJELSER ........................................................................8 CONSIDERACIONES GENERALES DE SEGURIDAD. ........................................................ 10 CONSIGNES GENERALES DE SECURITE ........................................
7. ERROR MESSAGE .............................................................................................................51 8. MAINTENANCE ...................................................................................................................52 9. 8-1 Removing the Play Panel ............................................................................................54 8-2 Replacing the Start Lamp / Switch ..............................................................................
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private use, without permission from NAMCO EUROPE LIMITED. While the information contained in this manual is given in good faith and was accurate at the time of printing, NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
NOTES ON INSTALLATION 1m76cm min NEVER turn the power to the machine ON until installation has been completed.
D Dieses Dokument darf in keiner Weise vervielfältigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datenträger (Suchsysteme), die Weitergabe oder sonstiges Kopieren für den gewerblichen und privaten Gebrauch sind untersagt und bedürfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED. Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behält sich jedoch das Recht zu Änderungen ohne vorherige Bekanntgabe vor.
HINWEISE ZUR AUFSTELLUNG 1m76cm min NIEMALS das Gerät einschalten bevor die Aufstellung völlig abgeschlossen ist. 50cm min 50cm min 2m50cm min Hinweis: Ist das Gerät für einen Aufstellplatz mit glattem Fußboden bestimmt, müssen die Standbeine mit Gummiplättchen unterlegt werden, damit das Gerät fest steht und nicht auf dem Boden hin- und herrutscht.
Denne udgivelse må ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den må heller ikke lagres i et eftersøgningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra Namco Europe Limited. Da informationerne i denne manual er givet med god tro og var korrekt på udskivningstidspunktet, forbeholder Namco Europe Limited sig retten til, at foretage ændringer og forandringer uden varsel.
PUNKTER OM INSTALLATION 1m76cm min Tænd aldrig for strømmen til maskinen før installering er fuldført. 50cm min 50cm min 50cm min For at undgå mulige elektriske stød sikres, at maskinen er forbundet til hovedstrømmen med sikkert monterede jordstik. 2m50cm min For at undgå skader på maskinen p.g.a. fejlbetjening sikres, at spændingen på hovedstrømmen er 230 volt AC.
No se permite la reproducción total ni parcial de esta publicación por ningún medio mecánico, fotográfico o electrónico, grabaciones fonográficas, ni su almacenamiento informático, su transmisión o su copia, ya sea para uso público o privado, sin permiso de NAMCO EUROPE LIMITED. Si bien la información contenida en este manual se da de buena fe y es correcta en el momento de su impresión, NAMCO EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.
NOTAS DE INSTALACIÓN. 1m76cm min JAMÁS ENCIENDA la máquina antes de haber completado la instalación. 50cm min 50cm min 50cm min Si el lugar donde se instalará la máquina tiene un piso pulido, se recomienda colocar tacos de goma bajo los ajustadores de nivel para evitar que la máquina se deslice por el suelo. Notas : Para acceder a las unidades de Fuente de Alimentación y CPU, asegúrese de que la parte trasera del mueble principal está separada de muros u otras máquinas al menos 500 mm.
Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d’enregistement phonographique. Ces informations ne seront ni stockées grâce à un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l’autorisation de NAMCO EUROPE LIMITED.
NOTES D’INSTALLATION 1m76cm min NE JAMAIS mettre le jeu en marche avant que l’installation ne soit complétement effectuée. 50cm min 50cm min 50cm min Note: Si l’endroit où doit être installée la machine à un sol pôli, il est recommandé de poser des tampons feutrés sous les vérins pour éviter que le jeu ne glisse sur le sol Afin de facilité l’accès aux CPU at à l’alimentation, s’assurer qu’il y a un espace d’au moins 500 mm entre l’arrière du meuble et le mur ou tout autre jeu.
ও Κανένα μέρος αυτής της έκδοσης δεν μπορεί να αναπαραχθεί με οποιοδήποτε μηχανικ" ,φωτογραφικ" ή ηλεκτρονικ" μέσο , ή με μορφή φωνητικής ηχογράφησης και ούτε να αποθηκευτεί με επανορθωτικ" σύστημα , να μεταδοθεί ή να αντιγραφεί για δημ"σια ή ιδιωτική χρήση , χωρίς την άδεια της NAMCO EUROPE LIMITED. Καθώς αυτές οι πληροφορίες σε αυτ" το εγχειρίδιο έχουν δοθεί με καλή πίστη και ακριβώς την ώρα της τύπωσης , η εταιρεία NAMCO EUROPE LIMITED κρατάει το δικαίωμα να κάνει οποιεσδήποτε αλλαγές χωρίς ειδοποίηση.
ΣΗΜΕΙΩΣΕΙΣ ΓΙΑ ΤΗΝ ΕΓΚΑΤΑΣΤΑΣΗ ΠΟΤΕ να μην ανάβει το μηχάνημα εάν δεν έχει ολοκληρωθεί η εγκατάσταση. 1m76cm min 50cm min 50cm min 50cm min Για την αποφυγή ηλεκτρικών σοκ πρέπει το μηχάνημα να έχει γειωθεί. 2m50cm min Για την αποφυγή βλάβης στο μηχάνημα λ"γο λάθος λειτουργίας , πρέπει η παροχή να είναι 230volt AC.. wall Playzone Pathway 1m min ΣΗΜΕΙΩΣΗ: Για την εύκολη πρ"σβαση στην κυρίως παροχή ή το CPU πρέπει η πίσω π"ρτα του μηχανήματος να απέχει τουλάχιστον 500mm απ" τον τοίχο ή άλλο μηχάνημα.
Nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza l’autorizzazione di NAMCO EUROPE LIMITED. Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione.
NOTES D’INSTALLATION NON ACCENDERE MAI la macchina finchè l’installazione non è stata completata. 1m76cm min 50cm min 50cm min Note: Per garantire l’accesso all’alimentatore e alla scheda madre, assicurarsi che il retro del mobile principale sia separato dalla parete o da altre macchine di almeno 500mm.
Ingen del av denne utgivelsen må reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra NAMCO EUROPE LIMITED. Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP LIMITED seg retten til å lage forandringer uten varsel.
MERKNADER VED INSTALLASJON 1m76cm min Slå ALDRI på maskinens strømforsyning før installasjonen er fullført. 50cm min 50cm min MERKNADER: For å få adgang til strømforsyningen og CPU-kort, forsikre deg om at bakparten av hoved kabinettet er skilt fra vegger eller andre maskiner med minst 500mm. 2m50cm min Hvis plassen hvor spillet skal plasseres har polerte gulv anbefales det at du benytter gummi sko under nivå justeringene, for å forhindre at maskinen kan flytte på seg.
Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe Limited.
Opmerkingen aangaande Installatie Sluit de machine nooit aan op de stroomtoevoer totdat de installatie is voltooid. 1m76cm min 50cm min 50cm min 2m50cm min OPMERKING: Als de machine op een gladde ondergrond wordt gebruikt, is het raadzaam rubber matjes onder de stelpootjes te bevestigen om te voorkomen dat de machine over de vloer gaat glijden.
Nenhuma parte desta publicacão poderá ser reproduzida por processos mecanográficos, fotográficos, electrónicos ou ainda sob a forma de gravacão sonora nem tão pouco poderá ser gravada através de sistemas informáticos transmissiveis ou de outra forma copiados para uso publico ou privado sem autorização expressa da NAMCO EUROPA LIMITADA. A informação contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicação.
NOTAS SOBRE A INSTALAÇÃO NUNCA ligar a maquina sem que a instalação esteja completamente finalizada. 1m76cm min 50cm min 50cm min NOTAS : Se esta maquina estiver colocada sobre um chão polido, recomenda-se a utilização de tapetes de borracha debaixo dos pés niveladores, afim de prevenir a maquina de deslizar no chão.
Ingen del av denna publikation får reproduceras, varken fotografiskt, elektroniskt eller i någon form av ljudinspelning. Det får inte heller lagras i något återvinningssystem, översändas eller på annat sätt kopieras för offentlig eller privat användning, utan tillstånd från NAMCO EUROPE LIMITED. Eftersom informationen i denna manual lämnas ut i god tro och var korrekt när den trycktes, reserverar sig NAMCO EUROPE LIMITED för ändringar.
ATT BEAKTA VID INSTALLATION 1m76cm min 50cm min 50cm min 50cm min Sätt aldrig på strömmen på maskinen innan installationen är klar. OBSERVERA: Om maskinen är placerad på ett polerat golv, rekommenderas att placera gummibrickor under nivåjusteringen för att förhindra att maskinen glider på golvet. För att kunna komma åt strömförsörjningen och CPU, se till att baksidan av huvudkabinettet är placerat minst 500 mm från vägg eller annan maskin.
Tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman NAMCO EUROPE LIMITED:in lupaa. Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. NAMCO EUROPE LIMITED:illä on kuitenkin oikeus muutoksiin ilman erillistä ilmoitusta. Tämä laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiivejä: 89/336/EEC ja 72/23/EEC (EN55014-1, EN55014-2 ja EN 60335-2-82 standardit).
ASENNUSHUOMIOITA 1m76cm min 50cm min 50cm min 2m50cm min wall Playzone Huomio: Jos tämä laite sijoitetaan liukkaalle esim. vahatulle lattialle, suositellaan laitettavaksi kumityynyt säätöjalkoihin liikkumisen estämiseksi. Pathway 50cm min Varmista, että virtalähteen jännite on 230 V AC, jotta ei laite vioitu. 1m min Tämän laitteen virtalähde on kytkettävä maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sähköiskun vaaraa ei olisi.
1.
2.
3. HOW TO PLAY This is a 1 or 2 player SWP shooting game, with a maximum single win of £40.00. The game consists of 3 (1 player game) or 4 (2 player game) mini-games that accumulate a cash sum depending upon the result of each mini-game. This total cash sum is played for in a win or lose final game. In the event of a 2 Player game, only the Player who has completed the most minigames in the fastest time will play for the final Cash Win Game. 1.
4. MOVING THE MACHINE This equipment is fitted with castors to make it easier to move. Take care when moving the equipment on an inclined floor. The overall height of this equipment is 1880mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables, etc.) 5. INSTALLATION Notes on Installation Never turn the power to the machine ON until installation has been completed.
1. 2. 3. 4. 5. 6. 쮕 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. This machine is designed for INDOOR USE ONLY. Do not install in the following places. Outdoors Direct Sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature. Places where it would be in the way of emergency exits or fire extinguishing equipment. Unstable places or places with excessive vibration.
1. 2. 3. 4. 5. 6. ও 1. 2. 3. 4 5. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS A l’extérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits où il y a des risques de fuite d’eau, près de ventilateurs ou source de chaleur, aux endroits très chauds ou froids.
1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6 1. 2. 3. 4. 5. 6. DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN Buiten In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd.
5-1 Adjusting the Level Adjusters 1. When the game is in it’s final position, lower the five (5) level adjusters, with a spanner, so that all castors are raised from the floor by approximately 5mm. Tighten the lock nuts with a spanner to ensure that the Level Adjusters do not move. Castor Lock Nut Approx.
6. ADJUSTMENTS 쮕 ও Adjustment or maintenance on this machine should be carried out by qualified personnel only. Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem Fachpersonal vorgenommen werden. Justeringer eller vedligehold af denne maskine bør kun udføres af kvalificeret personale. Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo por personal cualificado.
6-1 Adjustment Switches The Adjustment Switches are located inside the coin door. 1. Enter Switch. Press this switch to select options in the Test Mode. 2. Test Switch. Slide this switch ON to enter the test mode. Test mode allows the testing and changing of game settings. (refer to section 6-2 “Test Mode” page 38) 3. Select Up/Down Switch This switch is used to step through the test options and to alter the option settings.
6-2 Test Mode 1. Slide the Test Switch ON. The ‘Test Mode Menu’ screen will be displayed. 2. Use the Select Up/Down switch to select the required item. 3. Press the Enter Switch to enter the required test. 4. When all tests and adjustments have been completed slide the Test Switch OFF to return to normal game mode. TEST MODE MENU LOADED SOFTWARE:AFC2/VER.AX S/N: XXXX-XXXX Software Serial No.
6-2-1 Coin Options 1. Select ‘COIN OPTIONS’ from the test mode menu and press the Enter Switch. The following screen will be displayed. COIN OPTIONS F R E E P L AY: NO EXIT S E L E C T: S E L E C T S W U P / D O W N ENTER: ENTER SW < D E FA U LT I N G R E E N > 2 Use the Up/Down Select switch to choose FREE PLAY. Press the Enter Switch to change the setting from OFF > ON > OFF 3. Use the Up/Down Select switch to choose EXIT. Press the Enter Switch to return to the Test Mode Menu screen.
6-2-2 Game Options 1. Select ‘GAME OPTIONS’ from the test mode menu and press the Enter Switch. The following screen will be displayed. GAME OPTIONS MUSIC IN ATTRACT: YES LAMP BLINKING IN ATTRACT: YES P1 GUN BLOWBACK POWER LEVEL: 3 P2 GUN BLOWBACK POWER LEVEL: 3 EXIT SELECT: SELECT SW UP/DOWN ENTER: ENTER SW 2. Use the Up/Down Select switch to select the required item. Press the Enter Switch to change the setting. 3. Use the Up/Down Select switch to choose EXIT.
6-2-3 Total Plays Meter 1. Select ‘TOTAL PLAYS METER’ from the test mode menu and press the Enter Switch. The following screen will be displayed. TOTAL PLAYS METER COIN IN: 000000 COIN OUT: 000000 TOTAL PLAY: 000000 HOPPER DUMP: £000 RETURN THIS AMOUNT TO HOPPER: £00 SEE "PAYOUT ERROR HISTORY" EXIT SELECT: SELECT SW UP/DOWN ENTER: ENTER SW 2. Use the Up/Down Select switch to choose EXIT. Press the Enter Switch to return to the Test Mode Menu screen.
6-2-4 Switch Test 1. Select ‘SWITCH TEST’ from the test mode menu and press the Enter Switch. The following screen will be displayed. SWITCH TEST P1 TRIGGER :OFF P2 TRIGGER :OFF P 1 S TA RT :OFF P 2 S TA RT :OFF S E RV I C E :OFF SELECT :OFF TEST SW :ON ENTER :OFF EXIT : ENTER SW & SELECT SW UP/DOWN 2. The display will change from OFF to ON each time the corresponding switch is operated. 3. Use UP/DOWN Select switch and Enter Switch together to return to the Test Mode Menu screen.
6-2-5 Lamp and Blowback Test 1. Select ‘LAMP & BLOWBACK TEST’ from the test mode menu and press the Enter Switch. The following screen will be displayed. LAMP & BLOWBACK TEST P1 BLOWBACK TEST P2 BLOWBACK TEXT P1 START LAMP TEST P2 START LAMP TEST HEADER LAMPS TEST - (Not used) P1 SIDE LAMP TEST P2 SIDE LAMP TEST PAYOUT TRAY LAMP TEST EXIT SELECT : SELECT SW UP/DOWN ENTER : ENTER SW 2 Use the Select Up/Down Switch to select the required item, then press the Enter Switch to conduct the test. 3.
6-2-6 Monitor Test 1. Select ‘MONITOR TEST’ from the test mode menu and press the Enter Switch. The following screen will be displayed. CONVERGENCE NEXT TEST : ENTER SW 2. SELECT : SELECT SW UP/DOWN ENTER : ENTER SW & SELECT SW UP/DOWN Use the Enter Switch to toggle between the Convergence screen and the Colour Bar Screen. COLOUR BAR NEXT TEST : ENTER SW SELECT : SELECT SW UP/DOWN ENTER : ENTER SW & SELECT SW UP/DOWN 3.
6-2-7 Sound Test 1. Select ‘SOUND TEST’ from the test mode menu and press the Enter Switch. The following screen will be displayed. SOUND TEST LEFT CENTRE RIGHT SONG: 01 PLAY EXIT SELECT : SELECT SW UP/DOWN ENTER : ENTER SW 2. Use the Select Up/Down switch to select SONG, then press the Enter Switch. Use the Select Up/Down switch to change the song number. Press the Enter switch to return to item select mode. 3. Use the Select Up/Down Switch to select PLAY.
6-2-8 Cashflow Test 1. Select ‘CASHFLOW TEST’ from the test mode menu and press the Enter Switch. The following screen will be displayed. CASHFLOW TEST £0.10 : 000 £0.20 : 000 £0.50 : 000 £1.00 : 000 £2.00 : 000 EXIT: ENTER SW & SELECT SW UP/DOWN 2. Each time a coin is inserted through the Cashflow, the corresponding display will increase by 1. All numbers will return to 000 when exiting from this test. 3.
6-2-10 Initialize and Payout Setting 1. Select ‘INITIALIZE & PAYOUT SETTING’ from the test mode menu and press the Enter Switch. The following screen will be displayed. INITIALIZE & PAYOUT SETTING SETTING DEFAULTS OPTION: TOTAL PLAYS METER CLEAR: PAYOUT PERCENTAGE: 30 PAYOUT ERROR MESSAGE: AUTO RESET EXIT SELECT : SELECT UP/DOWN SW ENTER : ENTER SW 2 Use the Select Up/Down Switch to select the required item, then press the Enter Switch to conduct the test. 3.
6-2-11 Gun Initialize 1. Select ‘GUN INITIALIZE’ from the test mode menu and press the Enter Switch. The following screen will be displayed. P1 GUN INITIALIZE CHANGE GUN : SELECT SW UP/DOWN ADJUST GUN : ENTER SW EXIT : ENTER SW & SELECT SW UP/DOWN 2 Use the Select Up/Down Switch to select Player 1 or Player 2, then press the Enter Switch. The following screen will be displayed. P1 GUN INITIALIZE AIM AT CENTRE OF THE CROSS AND PULL GUN TRIGGER EXIT : ENTER SW & SELECT SW UP/DOWN 3.
4. Aim the gun at the “+” and pull the trigger. The “X”should overlap the “+”. Move the gun around the screen, without pulling the trigger, and ensure that the “X” overlaps the “+” when aiming at the “+”. If adjustment is OK, press the Enter Switch. Repeat the procedure for the other gun. If setting is not correct repeat the procedure. 5. Press the Select Up/Down switch and the Enter Switch together to return to the Test Mode Menu screen.
6-2-12 Payout Error History 1 Select ‘PAYOUT ERROR HISTORY’ from the test mode menu and press the Enter Switch. The following screen will be displayed. PAYOUT ERROR HISTORY 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: TOTAL: £ 0.00 RESET: EXIT £ £ £ £ £ £ £ £ £ £ 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 SELECT : SELECT SW UP/DOWN ENTER : ENTER SW 2. Use the Select Up/Down Switch to select the required item, then press the Enter Switch to conduct the test. 3.
7 ERROR MESSAGE This screen appears if insufficient winning coins are paid. Also all display lamps will light and blink. PAYOUT ERROR £3.00 Please call an attendant This error will be recorded in the “PAYOUT ERROR HISTORY” log. (see Test Mode 6-2-12 page 50) If the Payout Error Message has been set to AUTO RESET, (see Test Mode 6-2-10 page 47), the Error Message Screen will return to the normal Attract Mode screen after 10 minutes.
8. MAINTENANCE 쮕 ও Adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the POWER to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, service or repairs etc.) Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem Fachpersonal vorgenommen werden. Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der Netzstecker gezogen werden.
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine UITgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.) Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente por pessoal qualificado. Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutenção. (identifação de avarias, reparação etc.
8-1 Removing the Play Panel 1. Remove 3off security screw from the top of the Play Panel. 2. Remove 4off security screw from the underside of the Play Panel. Security Screw Security Screw 3. Lift the Play Panel only sufficient to reach the connectors, and disconnect the connectors. 4. Remove the Play Panel. 5. Reassemble in reverse order.
8-2 Replacing the Start Lamp / Switch 1. Remove the Play Panel. (see 8-1 page 54) 2. To remove the Microswitch, disengage the lug of the long retaining arm from the switch, lift the front of the switch up, and remove from the switch holder. Microswitch Long retaining arm Lug 3. To replace the lamp, twist the Lamp/Switch assy counterclockwise and remove from the Switch Body. Remove the lamp by pulling it straight out from the Lamp Holder 4. Reassemble in reverse order.
8-3 Replacing the Gun Assy 1. Remove the Play Panel. (see section 8-1 page 54) 2. Disconnect the connectors. 3. Remove 2off Whizz nuts (M6), and remove the Earth wires. 4. Remove the Gun Assy complete with gun cable and connector cover assy. Gun Assy Connector cover Play panel Earth terminal Whizz nut (M6) Rear side of play panel 5. Replace Gun Assy in reverse order. Ensure that the Earth wires are reconnected and fully secure.
8-4 Removing the Gun Slides 1. Remove 4off socket head screws (M3x10). Remove 1off button head screw (M4x25), taking care not to lose the M4 nut in the Gun Slide (L). Nut (M4) Socket cap screw (M3x10) Gun slide L Button head screw (M4x25) Socket cap screw (M3x10) 2. Remove the Gun Slides. 3. Reassemble in reverse order.
8-5 Removing the Gun Cover. 1. Remove the Gun Slides. (see section 8-4 page 57) 2. Lay the gun down on its left hand side. Nut (M4) Button head screw (M4x20) Lens Gun side (L) Gun PCB Button head screw (M4x10) Gun side R Socket cap screw (M3x10) 3. 4. 5. Button head screws (M4x10) Remove 4off button head screws (M4x10), 1off button head screw (M4x25) , and 1off socket head screw (M3x10). Take care not to lose any of the nuts in the left hand Gun Cover.
8-6 Replacing the Gun Solenoid 1. Remove the Gun Assembly. (see section 8-3 page 56 Replacing the Gun Solenoid Assy) 2. Remove the Gun Slides. (see section 8-4 page 57) 3. Remove the gun covers. (see section 8-5 page 58) 4 Disconnect the solenoid connector. 5. Remove 1off cap bolt (M3x10) and remove the solenoid bracket. Solenoid Cap bolt (M3x10) Solenoid bracket Connectors Ground terminal Toothed lock washer Cup screw (M) (M3x8) 6. Remove 1off cup screw (M3x8) and detach the ground wire.
8-7 Replacing the Gun Cable 1. Remove the Gun Assembly. (see section 8-3 page 56) 2. Remove the Gun Slides. (see section 8-4 page 57) 3. Remove the gun sides. (see section 8-5 page 58) 4. Detach the solenoid bracket, connector and ground wire. (see section 8-6 page 59) 5. Disconnect the sensor and detach the fast-on connectors from the micro switch. 6. Remove the button bolt (M4x10) fixing the conduit to the gun cover (L). 7. Remove 2off button bolt (M4x10) and remove the connector cover.
8-8 Replacing the Fluorescent Tube and Display Lamps 1. Remove 2off security screw (M5x25) and remove the Acrylic Retaining Bracket. Security screw (M5x25) Acrylic Retaining Brkt Display Acrylic 2. Remove the Display Acrylic. 3. Replace the Fluorescent Tube or Starter. 4. Remove the Wedge Lamps by pulling them straight out from the holder, and replacing them by pushing them into the holder. Lamp Holder Fluorescent Tube Starter Wedge Lamps (12v 5w) 5. Reassemble in reverse order.
8-9 Removing the Monitor 1. Remove 4off wood screws and remove the Monitor Cover Door from the rear of the cabinet. 2. Disconnect the connectors from the Monitor. Connectors 3. Loosen only 4off security screw retaining the Bottom Glass Bracket. 4. Remove 3off security screw, and remove the Top Glass Bracket. Note: Take care that the glass does not fall forward when removing the Top Glass Bracket.
5. Remove the Monitor Glass by tilting it forward at the top, and withdrawing it upwards from the Bottom Glass Bracket. Monitor glass 6. Remove the Screenprinted Monitor Surround. 7. Remove 4off hex head screws (with washers), and remove the Monitor from the front of the cabinet. Hex head screws Hex head screws 8. Reassemble in reverse order.
9 PARTS 9-1 Cabinet - Front 1 2 3 14 4 5 13 6 12 7 11 10 4 8 10 9 Page 64
Item Description Part No 1 Header Acrylic 30000096 3 2’ Fluorescent Assy 64500044 4 Wedge Lamp - 12v 5w 64000072 5 Front Glass 31000031 6 Screenprinted Monitor Surround 47000793 7 Front Glass Bracket - Bottom 47000795 8 Payout Acrylic 30000097 9 Coin Tower Decal - LHS 40000805 10 Wedge Lamp - 12v 1.
9-2 Cabinet - Rear 1 2 3 7 4 5 6 Page 66
Item Description Part No 1 Game PCB Assy XAFC-GAMEPCB 2 Fan - 4‰" 230v 67000015 Interlock Switch 60000006 Interlock Switch Cover 39000028 Schaffner Mains Filter Assy 62500010 Schaffner Boot 66000017 5 Adjustable Foot - M16 x 95 88300079 6 Swivel Castor - 75mm 59000005 7 Switchmode Power Supply - 200watt 1149-010 3 4 Parts not Shown Lamp Driver PCB 47000752 Transformer 18v @ 3A 67700015 Bridge Rectifier 71000040 Capacitor - 22,000 25v 70200043 Page 67
9-3 Hopper Door Assy 1 2 3 Item Description Part No 1 Mars CashFlow 9524 Front entry with Selector 65500766 2 Cold Cathode Tube Assy - White 64000132 3 Asahi Coin Hopper - £1 65501128 Page 68
9-4 Play Panel Assy 2 3 1 6 5 Item 1 4 Description Part No Panel Switch - Red 60200111 Play Panel Plastic - Bottom 47000753 Play Panel Plastic - Top 47 0 0 0 7 5 4 3 Panel Switch - Blue 60200112 4 Gun Holster Acrylic - Front 39000124 5 Play Panel Decal 40000807 Strain Relief Rope 4500 070 8 Gun Hoops 45000210 Red LED 64000104 2 6 Not Shown Page 69
9-5 Gun Assy 14 15 12 10 13 16 11 17 1 21 20 18 2 3 4 9 19 8 5 6 7 Page 70
Item 1 2 Description Par t No Gun Assembly - Red XPB-Gun-Red Gun Assembly -Blue XPB-Gun-Blue Gun Cover (LHS) - Red XPB-Cover-LR Gun Cover (LHS) - Blue XPB-Cover -LB Trigger Spring XPB-296-421 Trigger - Red XPB-Trigger-R Trigger - Blue XPB-Trigger-B 4 Solenoid - ST-0860A2 XPB-004-056 5 Tube Bracket (A) XPB-296-418 6 Gun Cord Harness Assy XPB-296-401 7 Tube Bracket (B) XPB-296-423 8 Connector Cover XPB-296-424 3 Gun Cover (RHS) - Red XPB-Cover-RR Gun Cover (RHS) - Blue XPB
9-6 Service Bracket 1 1 1 2 5 3 4 Item Description Part No 1 3.
10 SCHEMATIC LAMP CONTROL PCB Cabinet Assy 2P WHT/BLK 2P WHT/RED 1 1 WHT/RED 2 2 Uni 1 2 YEL 1 2 WHT/RED YEL YEL 1 1 WHT/BLK 2 2 Uni YEL 3 3 4 4 Uni WHT/BLK WHT/BLK GRY/YEL BLK WHT/BLK (L) HIDDEN WINDOW (R) 2P YEL 1 1 WHT/RED 2 2 YELLOW Uni WHT/RED BRN 4 0W 1 GRN/YEL 2 2 3 3 +5V 1 CONTROL (L) CONTROL (R) PAYOUT 2 1 2 3 4 3 4 2P RGB CABLE 1 BLK YEL/GRN 2 3 1 AC 2 AC 3 EARTH GRY/RED WHT/RED BLK Mini 6 Mini Sensor PCB Assy EI (AMP) 1 GND 2 SSIN 1 2 3 3 3P YEL YE
Copies of Namco Game Manuals can be downloaded from our website: www.namco.co.uk They are located under Components, Sales and Service For all Parts or Technical Support contact: Brent Electronic, Namco House, Units 5-8, Acton Park Estate, The Vale, London. W3 7QE www.brentelectronic.co.
