MANUAL OF USE AND MAINTENANCE
Foreword 3 Manual content, use and maintenance 3 Storage of manual of use and maintenance 3 Machine delivery 3 Namco Floorwash technical description 3 Serial number 3 General safety rules 3 Recommendations 4 Warnings 5 Technical data 6 Spare parts 7 Packaging specifications and dimensions 8 Machine unpacking 8 Machine assembly 9 How to get started 10 ON/OFF 11 Functioning 12 Transport 14 After cleaning 14 Maintenance 16 Troubleshooting tips 17 2
FOREWORD It is of outmost importance to keep the machine at its maximum efficiency by carrying out the maintenance described in this manual carefully. It is important to keep this instruction manual in a safe place so that it can be referred to whenever necessary. For further requirements, please contact our customer service centre or your nearest authorised dealer.
Recommendations • The machine is not intended to be used by persons (including children) whose physical, sensory and mental capacities are impaired, or with lack of the necessary experience and knowledge, unless they are supervised or instructed in its use by persons responsible for their safety. • Children shall be supervised to ensure that they do not play with the machine. • If the power supply is damaged, it shall be replaced by the manufacturer or its authorised technical assistance.
Warnings Always unplug the power cable from the outlet when not in use or before adjustments and maintenance are performed. Do not use or keep the machine outside in wet conditions, and avoid direct exposure to rain. Do not hold the plug or machine with wet hands. The machine is suitable for use in dry conditions at a temperature range of +5°C to +35°C (+41°F to +95°F). The power outlet socket of the machine shall be connected to an approved earth. Do not insert objects through openings.
Request original spare parts only to dealers and/or authorised resellers in case of parts replacement or maintenance. Check the machine in an authorised service centre at least once a year. Organise the disposal of waste materials complying scrupulously with current regulations.
SPARE PARTS 38 51 50 41 37A DAD2 37 20A VIT18 29 20B 18 VIT17 18A 18B 20C 20D 18C 18D 15 1 1A DAD2 CA 15 16 18 18A 18B 18C 18D 1A DAD2 39 VIT19 16 COMPLETE NYLON EXTERNAL LEFT SIDE NYLON EXTERNAL LEFT SIDE LOW SQUARE NUT 4MA MACHINE BODY UNIVERSAL REAR BRUSH UNIVERSAL FRONT BRUSH COMPLETE HEXAGON SPRING PLUNGER CH10 HEXAGON PLUNGER INSERT BUTTON CH10 HEXAGON PLUNGER CH10 SPRING LATCH FOR HEXAGON PLUNGER CH10 HEXAGON PLUNGER EJECT BUTTON CH10 1 20 20A 20B 20C 20D 37 37A 38 41 50 51 7 C
PACKAGING SPECIFICATIONS AND DIMENSIONS The Namco Floorwash machine is delivered in a protective packaging. Ensure that the packaging is fully intact and that there are no signs of tempering when the product is taken over. In case of damage, the customer shall notify our customer service immediately. 31 35 80 MACHINE UNPACKING Follow the procedure below: 1 Place the packaging on the floor/work table softly by laying it down on the right part.
MACHINE ASSEMBLY Follow the procedure below: The Namco Floorwash machine has a fast assembly system since no tools are required. Do not use any tool to avoid injuries or damage to the machine. 1 Place the body of the machine on a stable surface without slopes. 2 Insert the handle in the axle of the machine body. CLACK! 3 Insert the tank in the handle at the desired height (3 different heights). CLACK! 4 Insert the small transparent water tube in the relief valve situated on the lower part of the tank.
HOW TO GET STARTED The Namco Floorwash machine is a mechanical collection device that can achieve excellent results even with the use of water without detergent. An excellent result is achieved with the use of specific detergents. The machine comes with universal brushes (gr 0.12). Anyway, it is possible to request specific brushes to our customer service according to the type of surface to be treated. Use foam-controlled detergents to avoid excessive foaming. Do not use pure acids.
ON/OFF Before the start-up of the device, check that the electrical cord and the machine are not malfunctioning in any way. If this is not the case, do not use the device and contact our service centre as soon as possible. 1 Insert the plug in a 120 230-volt wall outlet. 2 Press the kick-start pedal situated at the bottom right side of the machine.
FUNCTIONING Check that all steps described above have been completed correctly before using the machine. Before starting the washing procedure with the machine, remove any solid residual such as dust lumps, stones, glass, paper etc. from the surface which has to be treated. 1 After the engine has turned on, move the machine back and forth with linear movements. The lever placed beneath the handle will allow you to dispense the liquid previously poured in the tank.
3 The recovery of the dispensed liquid occurs automatically by means of mechanical collection. The liquid will flow into the waste situated in the lower part of the machine. It is important to empty the waste when the seep liquid reaches the maximum mark printed on the back of the waste, thus avoiding an accidental release of the same.
TRANSPORT To transport the machine safely, follow these steps: Check that the tank is placed in a vertical position before moving the machine. The electrical cord shall be unplugged from the outlet. 1 The machine has two rubber wheels situated in the lower part. By pulling the tank towards you, without pressing the kick - start pedal, the front part of the machine will be lifted up, guaranteeing an easy transportation.
1 Open the upper cover of the machine by pushing the two lateral hooks up. 2 Remove and empty the dirty water waste. Wash it with running water and, if necessary, use a spatula to remove any residual from the bottom. The stainless-steel sheet welded to the waste is not removable. Do not try to remove it. 11 3 Unhook the upper cover and wash it gently with running water. Check that the drip tray and the water tube are not clogged.
MAINTENANCE A regular maintenance keeps the machine safe and always ready to use. Carry out the following operations: Before carrying out any operation, check that the electrical cord is unplugged from the outlet. 1 Keep the machine in a safe place to ensure its maintenance. Wear protective gloves when carrying out these operations, in order to avoid direct contact with metal edges or sharp plastic parts. 2 2 Unhook the handle from the machine body and place it on a work table.
2 4 Remove the brushes by pressing the button placed on the left side of the machine. Use a damp cloth to clean the internal sides of the machine while checking that seals are not clogged. 2 1 3 1 3 Do not clean the machine with steam cleaners. TROUBLESHOOTING TIPS The following are examples of some problems that may arise. If after completing the verifications listed below, you do not achieve positive outcomes, please contact our service support immediately.
NOTES 18
Namco Manufacturing 1651 Blalock Rd, Houston, TX 77080, 1729 Brittmoore Rd, Houston, TXU.S.A. 77043 Tel. 1-800-634-5816 Fax 713-932-9254 bryan@namcomfg.com www.namcomfg.