Data Sheet

NCC警語：取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率
或變更原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干
擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。
低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This device has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used following the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this device does cause harmful interference to radio or television reception, which can be determined by turning the device
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
·
Reorient or relocate the receiving antenna.
· Increase the separation between the device and receiver.
·
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled rolled environment. This device should
be installed and operated with a minimum distance of 20cm between the radiator and your body.
Important Note
This radio module must not be installed to co-locate and operating simultaneously with other radios in the host system except
following FCC multi-transmitter product procedures. Additional testing and device authorization may be required to operate
simultaneously with other radios.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware
programmed at the factory to match the intended destination. The firmware setting is not accessible by the end-user.
The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by
the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with
the modular transmitter installed.
The end-user manual shall include all required regulatory information/warnings as shown in this manual, including “This
product must be installed and operated with a minimum distance of 20 cm between the radiator and user body”.
This device has got an FCC ID: 2AEWY-NL04A. The end product must be labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: 2AEWY-NL04A”.
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20cm is maintained between the antenna and users, and the transmitter module may
not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed.
ISED Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1.This device may not cause interference.
2.This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux RSS exemptés de licence
d'Innovation, Sciences et Développement économique Canada. L'exploitation est soumise aux deux conditions suivantes :
1.Cet appareil ne peut pas provoquer d'interférences.
2.Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement
indésirable de l'appareil.
This device has got an IC: 20489-NL04A. The end product must be labeled in a visible area with the following: “Contains
Transmitter Module IC: 20489-NL04A”.
Cet appareil a un IC:20489-NL04A. Le produit final doit être étiqueté dans une zone visible avec
ce qui suit?"Contient le circuit intégré du module émetteur?IC:20489-NL04A".
Le manuel de l'utilisateur final doit inclure toutes les informations/avertissements
réglementaires requis, comme indiqué dans ce manuel, y compris "Ce produit doit être installé
et utilisé avec une distance minimale de 20 cm entre le radiateur et le corps de l'utilisateur".