ARMED READY ü SYSTEM FIRE Using Your XP-600 Security System AC ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 NAPCO Oi218a.
Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-600 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use.
Introduction Table of Contents Keypad Controls and Indicators ................................ Arming your System (When Leaving) ....................... Protecting Yourself While Home ............................... Emergency Keys ....................................................... Disarming the System ............................................... Silencing an Alarm..................................................... Resetting a Fire Alarm...............................................
Keypad Controls and Indicators * Key Used to enable special functions and options. Press *and then the corresponding Special Function number Option (See Special Functions, Page 11) Numerical Keys 1-9, 0. Used to enter User Codes, Zone numbers, etc. Ready Light will light when all zones are secure and system is ready to be Armed. ARMED READY üSYSTEM FIRE Bypass Key Used to bypass zones. Press Bypass and the corresponding zone number, and then Arm system.
Arming Your System Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding. If any zones cannot be secured, see Bypassing Zones below. 2 Enter your user code. The Green Ready light will go out, the Red Armed light will light. • If you make a mistake entering your code, press B and re-enter the code.
Arming Your System Protecting Yourself While at Home READY SYSTEM AC ZONE 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding. 2 Enter your user code. The Green Ready light will go out, and the Red Armed light will light.
Emergency Conditions E e Fire Emergency Enabled? Yes F F No Auxiliary Emergency Enabled? Yes G G No Police Emergency Enabled? Yes No Ambush Alarm Enabled? Yes No Emergency Buttons E FG The three sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time.
Disarming Your System / Silencing an Alarm Disarming Your System when Returning 1 2 ARMED READY Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, press the B key and re-enter the code.
Fire Protection Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan. To prepare your plan, draw floor plans of your building. (space is provided on the next page) Show two exits - a front or back door and a window from each room. (Make sure each window works. You may need a special fire-escape ladder if the window is high up.) Write down your outside meeting place.
Fire Protection Floorplan Draw a plan of your premises below. 10 Oi218a.
Special Functions A By pressing A followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: A0 Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing A followed by 0. This will allow the easy arming of the system by someone who is not a regular system user. A0 Easy Exit (when system is armed) This function (if programmed) allows an occupant to leave the premises without disarming the system.
ü System Troubles ARMED READY SYSTEM FIRE AC ZONE 1 The XP600 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the yellow ü SYSTEM light and beeping the keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used.
ü Keypad Beeps or ü SYSTEM Flashes 2 Beeps Zone light System Trouble ON Condition 2 Fire Trouble 2 Beeps 3 2 Beeps 4 3 Beeps 1-6 ARMED READY SYSTEM FIRE AC Warning: Replace batteries only with the same type as specified above. Use of another battery may present a risk of fire or explosion. Do not recharge or disassemble battery, or dispose of in fire. ZONE 2 4 Beeps 1-6 5 Beeps 1-4 ZONE 4 ZONE 5 ZONE 6 Action A problem has been detected in the Fire Circuit.
Programming User Codes Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program other user codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program Mode ARMED READY SYSTEM FIRE AC ZONE 1 ZONE 2 Press A followed by 8 and then enter the User 1 code. The Armed, Status and ü System Lights will flash, and the keypad will beep 4 times.
Glossary Ambush Code - In the event that you are forced by an intruder to disarm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station. If your system has the Ambush feature enabled, the code assigned as the User 6 code will function as your Ambush Code Arming / Disarming - Turning the system on or off by entering your user code at the keypad.
NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
