Technical Manual

4 All technical manuals are available in PDF format at tech.napcosecurity.com Napco iSecure Security System
INTRODUCTION
NAPCO's iSecure Security System is an easy to install, state-
of-the-art microcomputer-based bur-
glary alarm system with integral cel-
lular communicator. Installation al-
lows for wall mounting or placement
on a table top. iSecure supports up
to 80 wireless protection zones that
may be divided into 1 or 2 Areas,
each containing their own protection
zones. The basic system can be
easily expanded, with all Kits com-
patible with the following standard
devices:
IBR-TOUCH-WL Smart 7" Wire-
less IoT Touchscreen Keypad
ISEC-WL-TOUCH* Wireless 4.3" Full Color Security
Touchscreen Keypad
ISEC-WL-KEYPAD Wireless Battery-Powered Standard
Keypad
ISEC-WL-SIREN* Wireless Siren
ISEC-WL-MODULE* Wireless 8-Zone Takeover Module
ISEC-DW-XMITTER Low Profile Window/Door Transmit-ter
ISEC-KEYFOB 4-Button Pendant/Keychain Transmitter
ISEC-SMOKE Supervised Wireless Digital Smoke Sen-
sor
ISEC-MOTION Passive Infrared Motion Sensor
ISEC-GLASSBREAK Wireless Glass-Break Sensor
ISEC-CARBON MON Supervised Wireless Carbon Mon-
oxide Sensor
ISEC-PANIC Single Button Waterproof Panic
ISEC-HEAT Wireless Heat Detector with Rate of Rise
ISEC-ZWAVE* Z-Wave Module
ISEC-WIFI* Internet Module
ISEC-2WF-MOD 2-Wire Fire Sensor Module
SLE-EXTANT-KIT Adapter Cable for ANTEXT Kits:
SLE-ANTEXT30 30' Remote Antenna Kit
SLE-ANTEXT50 50' Remote Antenna Kit
SLE-ANTEXT75 75' Remote Antenna Kit
SLE-ANTEXT100 100' Remote Antenna Kit
See page 73 for ordering and additional information. Re-
fer to our website for the latest revisions of the documentation
FEATURES
 iPhone and Android phone apps allow for local and remote
arm / disarm, system status and Z-Wave control
 Integral 319MHz wireless receiver allows for compatibility
with all NAPCO 319MHz wireless transmitters
 Integral 4-wire bus terminals that support the GEMWV-
RECV (additional peripherals require power supply)
 Integral Ethernet 10/100 network connection for backup
central station communication, notifications and IBR-
TOUCH-WL operation
 Integral siren with Burg, Fire and CO Alarm cadences capa-
ble of 85dBA at 10 feet
 Integral voice prompts with 4 volume levels
 All Kits support up to six (6) ISEC-WL-KEYPADs and/or
ISEC-WL-TOUCHs, combined. When the Go-Anywhere
Hub is connected to a network with a Wi-Fi access point,
up to four (4) IBR-TOUCH-WL tablet keypads can be used.
 Powered by 16.5VAC transformer (included). Provision for
rechargeable 4AH or 5AH 12V backup battery (not supplied)
that automatically provides power during AC power outages
 System fully monitors AC power and charges the backup
battery
 LTE cellular radio module for wireless central station com-
munication, notifications, remote programming and firmware
downloads
 Integral supervised bell output
 Integral PGM output initiated by a keyfob button press
(toggle on/off or momentary on for 5 seconds)
 Cloud-based programming in the iSecure Cloud Web
Portal (www.iSecureByNapco.com)
 900MHz Wireless Transceiver Module for adding other wire-
less system peripherals, including the ISEC-WL-KEYPAD,
the ISEC-WL-TOUCH Touchscreen, the ISEC-WL-
MODULE Takeover Module and the ISEC-WL-SIREN.
 Optional ISEC-ZWAVE Z-Wave Module for programming/
control of Z-Wave home automation controls such as Z-
Wave-enabled lights, outlets, thermostats, garage door oper-
ators and door locks
 Optional ISEC-WIFI Internet Module for backup central sta-
tion communication and notifications (supplied in KIT 3; see
page 73 for kit ordering information).
 Optional SLE-ANTEXT30 / 50 / 75 / 100 Extended Range
Remote Indoor/Outdoor Antenna to increase LTE cellular
transmission signal strength (see WI2230 for instructions)
 Optional ISEC-2WF-MOD 2-Wire Fire Sensor Module that
supports 2 Fire zones (connect to Fire Power [+], Zone 7 [‒]
and Zone 8 [‒] terminals)
See page 73 for ordering and additional information.
Note: Not all pages in this manual apply to all systems.
Use the instructions for the peripherals and devices included
with the iSecure kit or for any additional devices purchased, as
required. All wireless devices, including Z-Wave devices,
must be signal tested with all enclosure covers fully
closed, including the Go-Anywhere Hub.
Note: iSecure, Gemini Wave (GEMWV) and Gemini (GEM)
transmitters are compatible with the iSecure system; however,
iSecure and Gemini Wave (GEMWV) transmitters are not com-
patible with Gemini GEM-Receivers.
To simplify the installation process, the Go-Anywhere Hub
can be programmed either through the programming screens in
the iSecure phone app or by accessing the same programming
screens in the iSecure Cloud Web Portal
(www.iSecureByNapco.com). In addition, a log containing up
to 800 events monitors Go-Anywhere Hub activity referenced
to a precision real-time clock. This detailed event history may
be displayed in the website page or in the app, as needed.
Overview
Go-Anywhere Hub
™
*Coming soon