Technical Manual

ManualsBrandsNapco Security Technologies ManualsComputers & AccessoriesThe Hub is the central unit that forms the alarm panel. The Hub connects to a variety of wireless sensors that perform various sensor interfaces in the premises.

Napco iSecure Security System All technical manuals are available in PDF format at tech.napcosecurity.com 61

Cold Start, Test and Reset Processes

Your iSecure Go-Anywhere Smart Hub and 900 MHz Keypads, Siren and take Over module can be reset back to their original

"default" conditions, i.e. the state each was in when they first left the factory. Proceed as follows:

Cold Start the Go-Anywhere Hub (Factory Default)

The Go-Anywhere Smart Hub can be reset back to its original "default" condition, clearing all programming and settings, includ-

ing all zones and keypads, and re-loading its factory default program.

1. Remove AC power from the Go-Anywhere Hub.

2. Separate the Go-Anywhere Hub front and rear housing by pushing in the two tabs at the bottom with a flat head screwdriv-

er until the tabs unhook. Battery power is removed upon separation of the housing.

3. Add a jumper to the two (2) pins of JP2 (located at the top left of the PC board).

4. Wait 60 seconds, or until error code E09-00 appears on the keypad or touchpad display.

5. Remove jumper from JP2.

6. Reassemble the front and rear housing and re-connect AC power.

7. Perform a Full Download of the Hub programming.

Factory Reset the ISEC-WL-SIREN

1. Remove power.

2. Place jumper on J1.

3. Power up siren. The siren will blink once with a strobe flash.

4. Remove jumper J1.

If the default process is successful, upon power up the LED will blink three times.

If unsuccessful, the LED will blink only once.

Test the ISEC-WL-SIREN (Strobe/Sounder Test)

Use hearing protection before testing! The siren is rated at 85dBA.

1. Remove AC and batteries.

The jumper pins on the siren PCB are marked "2 1" (see image at right). With the

unit oriented with the wall outlet AC prongs at the top, the factory storage position

for the jumper is across the top two pins.

2. Place jumper across the two bottom pins as shown to begin the test process.

3. Install batteries, observing polarity.

Upon the insertion of the 4th battery, the siren will sound and the strobe will flash.

4. Remove jumper and store in the top two pins for future use.

5. Remove batteries to silence; replace batteries and restore AC (if necessary).

Factory Reset the ISEC-WL-MODULE Takeover Module

1. Remove power.

2. Place jumper on J1.

3. Power up the module.

4. Wait 10 seconds and remove jumper from J1.

If the default process is successful, upon power up the LED will slowly blink.

Factory Reset the ISEC-WL-KEYPAD Wireless Battery-Powered Standard Keypad

1. Press and hold the AREA ( ) button until "LF" appears in the display.

2. Press 0, 2, ENTER.

If the default process is successful, the "dot" in the left bottom corner of the display and the word READY will appear. If

unsuccessful, only the "dot" in the left bottom corner of the display will appear. Note: This reset proce-

dure can only be initiated either within 1 minute after power up, or when the keypad flashes "o#" (where #

is the keypad address).

Factory Reset the ISEC-WL-TOUCH Wireless 4.3" Full Color Security Touchscreen Keypad

1. From the Home screen, press the System Settings ("gears") icon (shown at right).

2. Enter the Master Security Code (refer to the OI404LF card), then press ENTER.

3. In the System Settings screen that opens, press the Dealer KP Config button.

4. Press the LearnOff button. The LearnStatus will change from ON to OFF.

5. Press Exit twice to save and exit.

Note: To verify the LearnStatus, re-enter the System Settings screen and press the Dealer KP Config button.

System Settings

("gears") icon

ISEC-WL-SIREN Strobe / Sounder

Test Jumper Pins

(jumper shown when starting test)

2 1

prongs

(Store)

(Test)

Summary of content (20 pages)

PAGE 1
Cold Start, Test and Reset Processes Your iSecure Go-Anywhere Smart Hub and 900 MHz Keypads, Siren and take Over module can be reset back to their original "default" conditions, i.e. the state each was in when they first left the factory. Proceed as follows: Cold Start the Go-Anywhere Hub (Factory Default) The Go-Anywhere Smart Hub can be reset back to its original "default" condition, clearing all programming and settings, including all zones and keypads, and re-loading its factory default program. 1.
PAGE 2
Common Error Codes / Troubles E01 AC -- Power Failure This trouble will occur if AC power is not present. Make sure system transformer is plugged into AC receptacle and check the circuit breaker, otherwise call installing company for service. E01-89, E01-90, E01-91 and E01-92: AC loss for the ISEC-WLSIREN (#1 through #4) E01-93, E01-94, E01-95 and E01-96: AC loss for ISEC-WLMODULE Takeover modules (#1 through #4).
PAGE 3
ISEC-WL-KEYPAD "Local Functions" The ISEC-WL-KEYPAD includes internal keypad " local functions" that display certain keypad attributes as well as allow for the adjustment of some internal settings. Keypad Attributes This function displays certain keypad attributes that may be helpful when installing and configuring the system. 1. Press and hold the keypad AREA ( ) button until "LF" appears in the Window. 2. Press the keypad AREA button once ( ), then press ENTER.
PAGE 4
ISEC-WL-KEYPAD "Local Functions" (cont'd) 1. Press and hold the keypad AREA ( ) button until "LF" appears in the Window. 2. Press "0" and all keypad icons will briefly turn on at the same time (this is a test of the Window display). 3. Press ENTER. All signal strength readings in this function are expressed in dBm units (signal level relative to 1 milliwatt), provided for those more familiar with signal readings expressed using standard radio communication terminology.
PAGE 5
ISEC-WL-TOUCH "System Diagnostics" The ISEC-WL-TOUCH "System Diagnostics" screen shown below is exclusive to the ISEC-WL-TOUCH 4.3-inch 900MHz Color Touchscreen Wireless Keypad. It is designed to help you find the optimum mounting location for your ISEC-WL-TOUCH keypad by displaying the signal strength of the 900MHz radio signal link between the Go-Anywhere Hub and the ISEC-WL-TOUCH keypad within the installation environment.
PAGE 6
Keypad Dealer Function Menu The keypad can provide a wide assortment of utility functions as summarized in the Function Menu. The functions are displayed in a prompting "YES/NO" format. The complete Function Menu list is provided here in its normal displayed sequence. However, since not all functions are designed for all systems (or intended for all users), only functions that are applicable and active are displayed (e.g. if no zones are bypassed, "DISPLAY ZN BYPASSED" will not appear).
PAGE 7
Keypad Dealer Function Menu (cont'd) sounder for about 7 seconds. Tapping and poking at suspect points, the installer can easily locate swingers by listening for the beep. This eliminates the need of returning to the keypad to visually check after each attempt. Press RESET to restore normal operation (arming the system automatically cancels the Fault Find mode). Note: When testing wireless systems, the keypad will not beep if the signal strength is less than 3, but the strength will still be displayed.
PAGE 8
IBR-TOUCH-WL Dealer Settings Menu Run Diagnostics . Tap to run a system diagnostics test for components selected the last time the Setup Wizard was run (typically when the touchscreen was first powered). Functional components are marked with a check; items not configured or not enabled are marked with an "x". Selections are blank when the Wizard is run for the first time.
PAGE 9
IBR-TOUCH-WL Dealer Settings Menu (cont'd) Time interval to request status: Displays the duration between autodiscovery process activations. Connect using Wi-Fi Only a new "broadcast" SSID (named "BSSID" in this menu) to be stored in the touchscreen's memory, to be used by default when the touchscreen is rebooted, powered off/on or emerges from Screen lock. This selection MUST be checked (enabled).
PAGE 10
IBR-TOUCH-WL Dealer Settings Menu (cont'd) 1. The camera must be powered and wirelessly connected to the network before proceeding. "Keypad Skin" using the Update Logo menu selection (see above) and this logo is later tapped, the "dealer.png" image file will appear enlarged on the touchscreen. 2. Tap Yes to proceed or No to exit without saving any changes. If you tap Yes, the touchscreen will scan the network and all available cameras will be listed (by IP address) in the Camera List that appears.
PAGE 11
IBR-TOUCH-WL Dealer Settings Menu (cont'd) Zip Code: Tap to set the Zip Code to which the Weather Feed is associated. Update Automation Clock - Synchronizes the clock within the customer's router with the same time as the IBR-TOUCH-WL touchscreen. Lock Display on Keypad View - Enabled (checked) when "Keypad Only" is selected in the Setup Wizard (see below).
PAGE 12
Standby-Battery Calculation Worksheet Use the procedure given below to determine the required standby battery capacity in Ampere-Hours (AH). Note: It is not totally accurate to merely multiply the combined standby current (in amperes) by the standby time (in hours) to obtain the battery capacity (in ampere-hours), since other factors (Go-Anywhere Hub charging capabilities, temperature, battery condition, etc.) affect battery operation.
PAGE 13
Ordering Information ORDERING INFORMATION  IBR-TOUCH-WL Complete Professional System Kits  Kit 1 (ISEC-KIT1) with ISEC-WL-KEYPAD Wire- less Battery-Powered Standard Keypad: AllInclusive system includes a Go-Anywhere Smart Hub with up to 80 zones, siren and integral dual path cell/IP LTE reporting, wireless LCD keypad (lithium battery-powered), security and notifications from consumer app, 50' wireless PIR and two wireless window/door contact transmitters.
PAGE 14
Ordering Information (cont'd)  ISEC-HEAT Wireless Heat Detector with Rate  ISEC-SMOKE  ISEC-KEYFOB  Optional ISEC-WIFI Internet Module for backup of Rise: A high-quality 135°F (57°C) fixed temperature detector with Rate of Rise and built-in supervised digitally-coded radio transmitter. It is compatible with Napco's iSecure RECV series supervised receivers that monitor alarms, restores, low battery, tamper and status.
PAGE 15
ISEC-WL-SIREN Wireless Siren Mounting Template For Wall Outlets With a Center Cover Plate Screw Screw Hole Tab "Center Line of Wall Socket" Align this centerline with Wall Socket 5-1/4" Magnet Screws (2) (Use with battery powered units only) Slide Screw (Use with battery powered units only) 7/16" ENSURE THIS BOX IS 1 INCH X 1 INCH Napco iSecure Security System Magnet 1-5/8" All technical manuals are available in PDF format at tech.napcosecurity.
PAGE 16
Notes 76 All technical manuals are available in PDF format at tech.napcosecurity.
PAGE 17
ISEC-WL-SIREN Wireless Siren Mounting Template For Wall Outlets Without a Center Cover Plate Screw Screw Hole Tab This template shows the unit plugged into the bottom receptacle, but either can be used (or invert the unit as required). "Center Line of Wall Socket" Remove the two screws from the siren housing and replace screws with bracket in place, as shown.
PAGE 18
Notes 78 All technical manuals are available in PDF format at tech.napcosecurity.
PAGE 19
iSecure Hub Wiring Diagram Napco iSecure Security System All technical manuals are available in PDF format at tech.napcosecurity.
PAGE 20
N AP C O L I M I T E D WAR R AN T Y NAPCO SECURITY TECHNOLOGIES, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.