W415-0469 / A / 01.04.05 W415-0469 / A / 01.04.
TABLE of CONTENTS PG 2-4 INTRODUCTION Warranty Important Instructions Locating Your Fireplace Dimensions 5 ELECTRICAL CONNECTION 8 LIGHT REPLACEMENT 9-10 FINISHING Mantel Installation Clearance to Combustibles Framing and Finishing Hearth Cold Climate Installation Glass Removal Log Installation Optional screen installation REPLACEMENTS Ordering Replacement Parts Replacement Parts Accessories OPERATION Flame Effect Maintenance 5-7 7 11 TROUBLE SHOOTING GUIDE 12 RATING PLATE LOCATION PLEASE
NAPOLEON electric fireplaces are manufactured under the strict Standard of the world recognized ISO 9001:2000 Quality Assurance Certificate. NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. Once assembled the complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure that you, the customer, receive the quality product that you expect from NAPOLEON.
IMPORTANT INSTRUCTIONS LOCATING YOUR ELECTRIC FIREPLACE 1. READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. THIS APPLIANCE IS HOT WHEN USED. Your new fireplace may be installed into an existing masonry or zero clearance fireplace. It may also be installed using a prefabricated cabinet available from your dealer or may be built into a wall. For the best effect, install the fireplace out of direct sunlight. 2. To avoid burns, DO NOT let bare skin touch hot surfaces.
OPERATION There are two operation controls for the EF31. 1 - Controls the heater. 2 - Controls the flame effect. Control Door To access the contr ols controls ols,, slide the control door to the right. 1. Heater To set the heater at the maximum setting - roll the switch up to the uppermost setting. To turn the heater off - roll the switch down to the lower most setting. 2. Flame effect The rocker switch is used to turn the flame effect on and off.
EF31 HEARTH Corner Installation A hearth is NOT necessary but is recommended for aesthetic pur poses purposes poses.. COLD CLIMATE INSTALLATION WARNING: It is MAND ATOR Y to ha ve an insula ted w all beMANDA ORY hav insulated wall hind the fireplace, when the fireplace is being installed on an outside w all or c hase wall chase hase.. GLASS REMOVAL Top View Remove the two screws holding the glass retainer and pull the glass and retainer forward until the glass is past the fireplace bottom.
OPTIONAL SCREEN INSTALLATION 1. Bunch the curtain mesh in the middle of the rod. 2. Insert one end of the rod through the hole indicated in the side of the firebox frame. 3. The rod will need to be bowed in the middle in order to insert the other end of the rod into the opposite hole. 4. Tuck the bottom of the curtain mesh behind the front lip of the retainer. ELECTRICAL CONNECTION This fireplace requires a 15 amp, 120 volt and 60 hz circuit. The fireplace should be on its own circuit.
LIGHT REPLACEMENT There are two methods to replace the light: In either method, the electrical circuit breaker must be shut off until the replacement procedure has been completed at which time it can be turned back on. 2. Remove the five screws holding the defuser screen. Pull the top two corners in towards the center and remove from the unit. Light Bulb Replacement Method 1: 1. If the unit is not secured to the floor, turn the unit around to view the access panel. 2.
REPLACEMENTS Contact your dealer for questions concerning prices and availability of replacement parts. Normally all parts can be ordered through your Napoleon dealer or distributor. When ordering replacement parts always give the following information: FOR WARRANTY REPL ACEMENT PAR TS, A PHO TOCOPY OF REPLA ARTS PHOT THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM. 1. 2. 3. 4. 5.
W415-0469 / A / 01.04.
TROUBLE SHOOTING GUIDE SYMPTOM PROBLEM No Flame Light but - Light bulbs have burned out. everything else is TEST SOLUTION - Remove access panel and change light bulbs. working properly. Flame light, but no movement in the flame - Flame generator motor has burned out. - Flame generator has come loose. - Consult your local dealer. - Remove the access panel and check to make sure the flame generator is in the flame generator bracket, and is secured to the motor with the rubber tube.
RATING PLATE LOCATION There are two methods to gain access to the rating plate, located behind the access panel. Method 1: 1. If the unit is not secured to the floor, turn the unit around to view the access panel. 2. Remove the four screws securing the access panel. Method 2: 1. Remove the two screws holding the glass retainer and pull forward to remove the glass. Place the glass and retainer in a safe spot. 2. Remove the five screws holding the defuser screen.
