HI-TECH LISTED SOLID FUEL BURNING STOVES AND INSERTS INSTALLATION AND OPERATION INSTRUCTIONS EPA 1100, EPA 1100L, EPA 1100C, EPA 1400, EPA 1400L, EPA 1900, EPI 1101, EPI 1401

ManualsBrandsNapoleon Fireplaces ManualsStoveEPA 1100L

W415-0360 / 11.05.02

INSTALLATION AND OPERATION INSTRUCTIONS FOR

HI-TECH LISTED SOLID FUEL BURNING STOVES AND INSERTS

FREE STANDING MODELS

EPA 1100, 1100L, 1100C, 1400, 1400L

1900

INSERT MODELS

EPI 1101, 1401

INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.

CERTIFIED UNDER U.S. ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) JULY 1990 AND THE OREGON DEPARTMENT OF ENVIRONMENTAL QUALITY (D.E.Q.) PARTICULATE

EMISSION STANDARDS BY E.E.M.C. THESE STOVES HAVE BEEN TESTED AND LISTED BY WARNOCK HERSEY LTD. TO STANDARDS: CSA B366.2 , ULCS627, ULC S628, UL 1482.

MODEL 1100 HAS BEEN TESTED AND LISTED FOR INSTALLATION IN MOBILE HOMES.

Fax: (705)722-6031 www.napoleonfireplaces.com Email: ask@napoleon.on.ca

Wolf Steel Ltd., 24 Napoleon Rd.,

Barrie, ON., Canada L4M 4Y8 (705)721-1212

WARNING:

If this unit is not properly installed, a house fire may result.

FOR YOUR SAFETY

Follow the installation directions. This unit can be very hot when burning. Combustible materials

such as firewood, wet clothing, etc. placed too close can catch fire. Children and pets must be

kept from touching the unit when it is hot. The chimney must be sound and free of cracks. Before

installing your unit, contact the local building or fire authority and follow their guidelines.

Operate only with door tightly closed. Burn wood directly on firebricks. Do not use a grate or

elevate the fire. At least 14 square inches (90 sq.cm.) of outside air must be admitted to the room

or directly to the unit through a 4 inch (10cm.) diameter pipe. This unit is designed to burn natural

wood only. Higher efficiencies and lower emissions generally result when burning air dried sea-

soned hardwoods, as compared to softwoods or to green or freshly cut hardwoods. Do not start a

fire with chemicals or fluids such as gasoline, engine oil, etc. Do not burn treated wood, coal,

charcoal, coloured paper, cardboard, solvents or garbage which tend to produce more pollution

than wood. Do not let the unit become hot enough for any part to glow red.

KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C). Attempts to achieve heat output rates

that exceed design specifications can result in steel distortion and damage.

R-2000

Summary of content (16 pages)

PAGE 1
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER. CERTIFIED UNDER U.S. ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) JULY 1990 AND THE OREGON DEPARTMENT OF ENVIRONMENTAL QUALITY (D.E.Q.) PARTICULATE EMISSION STANDARDS BY E.E.M.C. THESE STOVES HAVE BEEN TESTED AND LISTED BY WARNOCK HERSEY LTD. TO STANDARDS: CSA B366.2 , ULCS627, ULC S628, UL 1482. MODEL 1100 HAS BEEN TESTED AND LISTED FOR INSTALLATION IN MOBILE HOMES.
PAGE 2
NAPOLEON wood fireplaces are manufactured under the strict Standard of the World Recognized ISO 9001 : 2000 Quality Assurance Certificate. NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. The complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure that you, the customer, receives the quality product that you expect from NAPOLEON.
PAGE 3
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE TABLE of CONTENTS PG 2-4 INTRODUCTION 10-11 FINISHING Warranty General Information Care of Plated & Enamelled Parts Care of Glass Brick Installation Ornamental Trivet Installation Door and Handles Installation Pedestal Trim Installation 5-6 INSTALLATION 11-13 OPERATING INSTRUCTIONS Installing the Legs Alcove Installation Stove Installation Chimney Connection Adding Chimney Sections Outside Air Achieving Proper Draft Fire Extinguishers and Smoke Detec
PAGE 4
INTRODUCTION GENERAL INFORMATION Except for their different depths, models 1100, 1400, 1900 and the fireplace inserts 1101 and 1401 are identical and use the same burning principles. They were specifically designed over many months of research to meet the 1990 U.S.A. EPA particulate emission standards and have been extensively tested in Canadian and American laboratories.
PAGE 5
STOVE INSTALLATION INSTALLING THE LEGS To avoid being damaged during shipping, the stove has been bolted to the pallet and must be unbolted before the stove can be installed. FIGURE 2A 1. Remove the 4 nuts and washers from the underside of the pallet. 2. Lift the stove up and away from the pallet to clear the threaded studs sticking through the pallet. Place the stove on its back onto a protective surface such as a carpet or blanket to avoid scratches during leg installation.
PAGE 6
DO NOT USE ANY MAKESHIFT MATERIALS DURING INSTALLATION. 1. Move the stove into position with the flue centered, midpoint between two joists to prevent having to cut them. Use a plumb bob to line up the centre. 2. Cut and frame an opening in the roof to provide a 2" clearance between the outside of the chimney and any combustible material. DO NOT FILL THIS SPACE WITH ANY TYPE OF MATERIAL. Nail headers between the joist for extra support.
PAGE 7
OUTSIDE AIR Connection from the stove's air intake to the outside is mandatory in mobile homes only, either through a hole in the wall to line up with the knockout in the pedestal back, or through a hole in the floor to line up with the hole in the pedestal base. Use a fresh air kit. Secure the 4 inch diameter aluminum liner by flaring the end once it is inserted through the 4-1/2 inch diameter hole in either the back or base of the pedestal.
PAGE 8
In the United States, continued: If a continuous liner is not installed, a "direct flue connection" must be made. The direct flue connection requires a non-combustible connector that extends from the insert into the chimney flue liner and also that the installed flue cover be sealed below the entry point of the connector to prevent dilution of combustion products in the chimney flue with air from inside the house. Cap the top of the chimney using an approved rain cap.
PAGE 9
1101 FAN SERVICE OR REPLACEMENT 1. Turn off all electrical power to the insert. Remove the glass door and set aside in a safe place. 2. Remove the top right GASKET side bricks from inside the firebox, 4-#7's and 2#2's. Then remove the rest of the side and back bricks from the right side of the 1101 insert. It is not necessary to remove the bottom bricks. THERMAL SWITCH 3. The access panel can be removed by taking out the 8 #10 self taping screws. A 5/16" nut driver will be required to complete this job.
PAGE 10
FINISHING SIZES 1100/1100C 1400 1401/1400L 1900 BACK 4-#1 2-#4 4-#1 2-#4 4-#1 2-#4 4-#1 2-#4 4-#7* 2-#2 SIDES 8-#1 2-#3 8-#1 2-#3 12-#1 12-#1 12-#7* 2-#3 2-#4 (notched) 2-#102-#10 2-#11 2-#11 2-#12 4-#1 2-#2 5-#1 2-#2 1-#5 1-#6 6-#1 2-#2 7-#7* 2-#2 1-#5 1-#6 2-#2 1-#8 1-#9 2-#2 1-#8 1-#9 2-#2 1-#8 1-#9 2-#2 1-#8 1-#9 #1. #2. #3. #4. 1-1/4" x 4"-1/2 x 9" 1-1/4" x 3" x 9" 1-1/4" x 4-1/2" x 4-1/2" 1-1/4" x 4-1/2" x 9" #5. #6. #7.
PAGE 11
BRICK and BAFFLE INSTALLATION With stove and chimney installation completed, move the bricks into place by working as illustrated for your unit on page 10. 1. Install two or three courses of brick on both sides of the unit. Install two courses on the back wall. Install the final course of bricks on the back wall. These bricks are held in place by a brick retainer. Before installing the bricks, loosen the screw holding the retainer and ensure that it has been moved forward.
PAGE 12
You can now add larger pieces of wood and operate the stove normally. Once the stove/insert is entirely hot, it will burn very efficiently with little smoke from the chimney. There will be a bed of orange coals in the firebox and secondary flames flickering just below the top firebrick.
PAGE 13
DO NOT OVERFIRE THE STOVE! Overfiring can occur by: a) burning large amounts of smaller wood pieces such as furniture scraps, skids or treated wood; b) vigorously burning large loads of wood with the draft control on "HIGH" (fully open) for long periods of time (one or two hours). maintenance 13 Check your chimney and chimney connector for creosote and soot buildup weekly until a safe frequency for cleaning is established.
PAGE 14
WOOD PILE MAINTENANCE Burn only dry, clean unpainted wood that has been seasoned. It produces more heat and less soot or creosote. Freshly cut wood contains about 50% moisture while after proper seasoning only about 20% of the water remains. As wood is burned, this water boils off consuming energy that should be used in heating. The wetter the wood, the less heat is given off and the more creosote is produced.
PAGE 15
ORDERING PROCEDURES Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Napoleon dealer or distributor. When ordering replacement parts always give the following information: 1. Model & Serial Number of fireplace 2. Installation date 3. Part Number 4. Description of part 5. Finish REPLACEMENT PARTS ACCESSORIES / OPTIONS # PART NO.
PAGE 16
35 39 34 1 38 17 35 37 36 15 19 43 32 28 49 44 33 31 55 24 1 29 48 40 57 52 W415-0360 / 11.05.