User Guide

ManualsBrandsNapoleon Grills ManualsOtherBUILT-IN GRILLS

BUILT-IN UNIT INSTRUCTION GUIDE

N415-0107 / APR 28/06

Please use this manual in conjuction with your main manual to properly assemble your built-in grill. Refer to the

main manual for operating, cleaning, and maintenance instructions. This grill is designed for non-combustible

enclosures only, and must be installed and serviced by a qualified installer to local codes.

BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as

shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an

approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane installation code in

Canada, or to the National Fuel Gas code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"

for rigid pipe, and 1/2" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN

B149.1. Propane Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The gas

supply must be connected to the 3/8” flare elbow fitting located under the right hand side of the control panel. If installing a side

burner, a separate line must be branched off to the side burner unit and enter the side burner opening at the specified location. If the

enclosure is to house a propane cylinder, the tank portion of the enclosure must be ventilated according to local codes, and must not

have communication with the cavity used to enclose the gas grill. The tank can not be stored below the gas grill.

BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as

shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an

approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane Installation Code in

Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"

for rigid pipe, and 5/8" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN

B149.1. Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States.

Built in units are supplied with a drip pan which holds only a minimal amount of grease. To prevent grease fires, the pan must

be cleaned after each use.

SERIAL #______________________

Summary of content (9 pages)

PAGE 1
SERIAL #______________________ BUILT-IN UNIT INSTRUCTION GUIDE Please use this manual in conjuction with your main manual to properly assemble your built-in grill. Refer to the main manual for operating, cleaning, and maintenance instructions. This grill is designed for non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes.
PAGE 2
BUILT-IN UNIT OPENING DIMENSIONS BUILT-IN SIDEBURNER BIU405 BUILT-IN GRILL HEADS OUTDOOR GFI OUTLET RECOMMENDED - LOCATE ON LEFT SIDE OF GRILL FOR ROTISSERIE USE. W BIPT450 / BIPT600 / BIPT750 BUILT-IN GRILL HEADS D H 1¾” 6” . 3” MIN D 1¾” H D 7” H 2” 4” GAS INLET OPENING W GAS INLET OPENING W GAS INLET OPENING 34” RECOMMENDED DEPTH OF COUNTERTOP OVERHANG MINIMUM 10 SQ IN OF VENTILATION REQUIRED ON EACH END OF CABINET WIDE 1 ¼” OVERHANG NOTCH REQUIRED IF USING SUPPLIED TRIM KIT.
PAGE 3
BUILT-IN ACCESSORY OPENING DIMENSIONS D NOTE: ACCESSORY FRAMES OVERLAP OPENING BY 1 ½” ON ALL 4 SIDES H W Part # Description Picture OPENING DIMENSION W H N370-0069 Flat vertical painted door 13 ¼” 18 ¼” N370-0071 Flat vertical stainless steel door 13 ¼” 18 ¼” N370-0070 Flat horizontal painted door 18 ¼” 13 ¼” N370-0072 Flat horizontal stainless steel door 18 ¼” 13 ¼” N370-0356SS Curved stainless steel door - 308 size 22 ½” 19 ¾” N370-0357SS Curved stainless steel door - 450 si
PAGE 4
1. BIPT450 BUILT-IN INSTRUCTIONS N080-0142 N080-0142 N570-0026 N715-0062 N715-0060 N715-0059 N710-0027 N715-0061 This grill is designed for masonry, non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes. 1. Attach side mounting brackets and side trim pieces to each side of the grill using #14 x 1/2" screws (n570-0026). 2. Mount the lower front trim to the bottom front edge of the opening (fasteners not included). 3.
PAGE 5
2. BIPT600 BUILT-IN INSTRUCTIONS N080-0142 N570-0026 N380-0009 N080-0066 N051-0001 N715-0060 N710-0044 N715-0059 N715-0072 This grill is designed for masonry, non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes. 1. Attach side mounting brackets and side trim pieces to each side of the grill using 1/4-20 x 1/2" screws (n570-0026). 2. Mount the lower front trim to the bottom front edge of the opening (fasteners not included). 3.
PAGE 6
2. BIPT750 BUILT-IN INSTRUCTIONS N080-0142 N570-0026 N380-0009 N051-0001 N715-0076 N715-0060 N710-0044 N715-0059 N715-0077 This grill is designed for masonry, non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes. 1. Attach side mounting brackets and side trim pieces to each side of the grill using 1/4-20 x 1/2" screws (n570-0026). 2. Mount the lower front trim to the bottom front edge of the opening (fasteners not included). 3.
PAGE 7
3. BIU405 BUILT-IN INSTRUCTIONS N080-0152 N715-0063 N570-0026 N570-0026 N570-0026 N080-0152 23 e c-c N080-0155 N080-0155 This grill is designed for masonry, non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes. Access must be provided in the enclosure for drip tray removal and cleaning. 1. Attach the side mounting brackets and the rear trim to the unit using #14 x 1/2” screws (n570-0026).
PAGE 8
4. BUILT-IN SIDE BURNER INSTRUCTIONS N280-0003P (BLACK) N280-0004 (STN STL) 1. Fit the side burner frame into the opening. The frame should be attached to the opening to prevent any future movement (fasteners not included). 2. Ensure that there is at least 5 sq in of opening in the bottom of the cut out, for combustion air. 3. Set the side burner into the frame. 4. Connect the gas supply to the side burner valve. Leak test the entire installation before operating the unit.
PAGE 9
5. BUILT-IN ACCESSORY DRAWER INSTRUCTIONS 1. Unpack the drawer frame assembly. 2. Remove the drawers from the enclosure by fully extending them and then lifting up to remove them from the slides. 3. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located at the same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to ensure that the front of the enclosure is plumb. 4.