SERIAL / SÉRIE#______________________ DECORATIVE INDOOR WATERFALLS THAT PURIFY AND HUMIDIFY THE AIR WF 6/9/18 WF9ST MANUFACTURED BY / MANUFACTURE PAR: NAPOLEON APPLIANCE CORP., 214 BAYVIEW DR., BARRIE, ONTARIO, CANADA L4N 4Y8 PHONE: (705)726-4278 FAX: (705)725-2564 EMAIL: ask@nac.on.ca WEB SITE: www.napoleongrills.
NAPOLEON waterfalls are manufactured under the strict Standard of the world recognized ISO 9001-2000 Quality Assurance Certificate. NAPOLEON products are designed with superior components and materials, and are assembled by trained craftsmen who take great pride in their work. Every component is thoroughly inspected by a qualified technician before packaging and shipping to ensure that you, the customer, receive the quality product you expect from NAPOLEON.
indoor air quality Your new NAPOLEON waterfall will dramatically improve the indoor air quality in your home. The waterfall is a natural humidifier which helps alleviate dry skin and allergies. This is extremely beneficial in dry climates and also cold climates where forced air furnaces dry the air. The waterfall also cleans the air by attracting contaminants. Moving water attracts airborne particles, such as dust, pet dander, pollen and other pollutants.
water Water is perhaps the most critical component in the waterfall. Dirty or contaminated water will quickly cause operational problems with your waterfall. House water must be softened and filtered if the unit is to be connected to the water supply. RO (Reverse Osmosis) water will give the best results, and require the least amount of maintenance. If the unit is not being connected to the house supply, distilled bottled water is recommended.
INSTALLATION The framing dimensions are included in the framing specifications drawing. The unit is designed to be installed after drywalling. For added protection water resistant drywall (green board) or cement board are recommended in the vicinity of the fountain. The fountain is designed to be attached to the studs over the drywall along both vertical sides of the fountain using drywall screws. This will leave a basically flush surface to trim over. Leak test the waterfall before fully enclosing.
WF9 WF6 WF18 BACKBOARD BACKBOARD BACKBOARD 35.250” MORTAR MORTAR 35.250” TILES TILES 70.50” 23.625” 35.50” MORTAR CUSTOM SURFACE PANEL: Panels can also be made using materials such as mirror, glass, slate, marble or ceramic tile for display in your waterfall. If tiling, use waterproof cement board as a backer, available at any building centre. Cut the cement board to the size of your TILES existing stainless steel panel. Ensure that the tiles can be used in a wet environment.
TROUBLESHOOTING Problem Water not flowing. Dry spots on waterfall surface. Lights not working. UV-light not working. (optional) Possible Causes Solution Pump not plugged in. Plug pump into nearest GFI protected receptacle. Insufficient water level. Add water to recommended level. Pump must be submerged by 1-2” at all times. Water flow control valve turned off. Turn valve to on position. Sediment filter plugged. Replace filter. Pump is “vapour-locked”.
ORDERING REPLACEMENT PARTS Before contacting the customer service department, check the NAC web site for more extensive cleaning, maintenance, troubleshooting and part replacement instructions at www.napoleongrills.com. Contact the factory directly for replacement parts and warranty claims. The customer service department is available between 9 AM and 5 PM (Eastern standard time) at 1-866-820-8686 or fax at 1-705-727-4282. In order to process a claim, we must be provided with the following information: 1.
FRAMING SPECIFICATIONS 2x6 HEADER PANEL RECOMMENDED CHECK WITH LOCAL CODES HEIGHT Ø1.50” 4.00” CENTERS CONTINUE DRYWALL UP TO THIS EDGE 24” RECOMMENDED* WIDTH CHECK WITH YOUR LOCAL BUILDING AUTHORITY FOR COMPLETE FRAMING GUIDELINES. THE CHART BELOW WILL GIVE YOU THE OPENING SIZE REQUIRED FOR EACH MODEL. EACH WATERFALL IS INTENDED TO BE MOUNTED ON TOP OF THE DRYWALL (NOT SHOWN). THE DRYWALL BELOW THE UNIT SHOULD CONTINUE UP TO THE BOTTOM OF THE WATERFALL BASIN. MODEL HEIGHT WIDTH WF6 49.00” 26.
PIPING DIAGRAM WITHOUT UV LIGHT 6X N570-0043 (8-32 X 3/4") TO ELECTRICAL OUTLET 2 1 FROM THREE WAY VALVE TO WATERFALL FROM WATERFALL DRAIN TO BASIN A B FROM BASIN TO WATERFALL DRAIN A FROM THREE WAY VALVE TO WATERFALL B FROM WATER SOURCE TO FLOAT VALVE INSTALL THE SUPPLIED HOSE CLAMPS ON EITHER SIDE OF THE BASIN CUT THE SHORT PIECE OF BLACK TUBING TO 14” OVERFLOW PROTECTION SADDLE VALVE (NOT INCLUDED) SEDIMENT FILTER FLOW CONTROL VALVE / PURGE VALVE TO DRAIN PURGE LINE 10 Remove components
PIPING DIAGRAM WITH UV-LIGHT 9X N570-0043 (8-32 X 3/4") TO ELECTRICAL OUTLET 1 3 2 4 FROM THREE WAY VALVE TO WATERFALL A FROM WATERFALL DRAIN TO BASIN B A FROM BASIN TO WATERFALL DRAIN FROM THREE WAY VALVE TO WATERFALL B FROM WATER SOURCE TO FLOAT VALVE INSTALLTHE SUPPLIED HOSE CLAMPS ON EITHER SIDE OF THE BASIN SADDLE VALVE OVERFLOW PROTECTION TO DRAIN UV LIGHT SEDIMENT FILTER FLOW CONTROL VALVE / PURGE VALVE PURGELINE Remove components from basin and assemble as shown.
WATERFALL SURFACE INSTALLATION The stainless steel panel provided with WF6, WF9, and WF18 is installed simply by sliding the top of the panel under the retaining bracket at the top of the waterfall, and pushing it high enough to slip over the bottom support brackets. The welded brackets that protrude at an angle from the waterfall housing, merely provide pressure to the panel to prevent it from bowing. The optional acrylic panel can be placed in front of the stainless steel panel in the same manner.
PARTS DIAGRAM 13
