INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE. INSTALLATION AND OPERATING INSTRUCTIONS CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278 CSA STANDARD EF39HD ELECTRIC FIREPLACE CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
TABLE OF CONTENTS 1.0 2.0 3.0 INTRODUCTION 3 1.1 1.2 1.3 4 4 5 LOCATING APPLIANCE 6 2.1 2.2 2.3 6 6 7 5.0 6.0 7.0 8.0 9.0 10.0 UNPACKING AND TESTING APPLIANCE GROUNDING APPLIANCE HARD WIRE INSTALLATION INSTALLATION 3.1 3.1.1 3.1.2 3.1.3 4.0 DIMENSIONS LISTING APPROVALS GENERAL INSTRUCTIONS WALL MOUNT INSTALLATION MINIMUM CLEARANCE TO COMBUSTIBLES MINIMUM MANTEL CLEARANCES INSTALLING THE APPLIANCE 8 9 9 9 10 FINISHING 11 4.1 4.
1.0 INTRODUCTION ! • • • • • • • • • • • • • • • • • • • • • • • • • • • • • WARNING THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED. Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fire or injury. Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before servicing.
1.1 DIMENSIONS 7 1/4” 39 3/16” ELECTRICAL INLET 28 1/16” 25” 29 1/8” 2” 51/4” Heat Vents (Do not cover) Power Switch 37 1/4” 1.2 LISTING APPROVALS This appliance has been tested in accordance with the CSA Standards for fixed and location-dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer.
1.3 GENERAL INSTRUCTIONS ! WARNING READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT. THIS ELECTRIC APPLIANCES IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL ACCESSORIES LISTED IN THESE INSTRUCTIONS.
2.0 LOCATING APPLIANCE ! WARNING DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS, CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE. NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER WATER CONTAINER. WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND MAINTENANCE.
2.3 HARD WIRE INSTALLATION If it is necessary to hard wire this appliance, a qualified electrician may remove the cord connection, and wire the appliance directly to the household wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in United States. COVER PLATE STRAIN RELIEF A.
3.0 INSTALLATION ! WARNING RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER. RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER.
3.1 WALL MOUNT INSTALLATION 3.1.1 MINIMUM CLEARANCE TO COMBUSTIBLES Measurements are taken from the glass front. 3 Bottom 19 /4" Top 2 1/2" to mantel Sides 4" Top 4 1/2" to ceiling Back 0" 3.1.2 MINIMUM MANTEL CLEARANCES ! WARNING WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE HEAT RESISTANT TO PREVENT DISCOLOURATION. Mantel 2 1/2” Wall Floor Side View W415-0752 / B / 06.03.
3.1.3 INSTALLING THE APPLIANCE Due to the many different materials used on different walls, it is highly recommended that you consult your Body local builder before you install this appliance on the wall. A. Glass Front Select a location that is not prone to moisture and is located at least 36" away from combustible materials such as curtain drapes, furniture, bedding, paper, etc. B. Have two people hold the appliance against the wall to determine the final location. C.
4.0 FINISHING ! WARNING POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID RECONSTRUCTION. HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES. 4.1 GLASS EMBER INSTALLATION Glass front must be removed and the appliance must be mounted in its final location before the glass embers are installed. Glass embers may have sharp edges, wear safety glasses and gloves when handling. 4.2 A.
5.0 OPERATING INSTRUCTIONS Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate. NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power failure, when the main power switch is in the "I" ON position and the hand held remote control is in the OFF position, the flame generation lights will come on at the high setting. 5.1 MAIN POWER SWITCH The Main Power Switch is located on the bottom of the appliance as illustrated.
6.0 MAINTENANCE ! WARNING PREPARATION FOR MAINTENANCE ALWAYS DISCONNECT THE POWER AND ALLOW THE ELECTRIC APPLIANCE TO COOL BEFORE PERFORMING ANY CLEANING, MAINTENANCE OR RELOCATION OF THIS ELECTRIC APPLIANCE. TURN CONTROLS TO OFF AND REMOVE PLUG FROM OUTLET OR TURN OFF THE HOUSE CIRCUIT BREAKER TO ELECTRIC APPLIANCE RECEPTACLE. DO NOT INSTALL REPLACEMENT BULBS THAT EXCEED SPECIFIED MAXIMUM WATTS. THE HALOGEN LIGHT BULBS IN YOUR APPLIANCE CAN BECOME EXTREMELY HOT.
6.1 REPLACING THE FLAME GENERATION LIGHT BULBS ! WARNING REMOVE THE APPLIANCE FROM THE WALL AND TURN OFF ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE. A. Remove the 6 screws on the back plate of the appliance near the bottom. Open back plate from the top. B. Locate the flame generation cylinder drum. It is attached to the inside of the back plate. They are 2 matte black sheet metal pieces with holes in them, either of which can be removed from the appliance. C.
6.2 REPLACING THE EMBER BED LIGHT BULBS Ember Bed Bulb Replacement Ember Bed Bulb Replacement 2 screws Screw Back View Right Left Screw Screws Switch wires A. Remove the 2 screws on the bottom left and right corner of the appliance behind the front panel. B. Remove the 2 screws holding the main power switch and pull switch down carefully. Before removing the wires we recommend labelling the 3 wires on the switch.
7.0 REPLACEMENT PARTS Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Authorized dealer / distributor. FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.
8.0 TROUBLESHOOTING ! WARNING TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
9.0 WARRANTY NAPOLEON® electric appliances are manufactured under the strict Standard of the world recognized ISO 9001 : 2008 Quality Assurance Certificate. NAPOLEON® products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. Once assembled the complete appliance is thoroughly inspected by a qualified technician before packing to ensure that you , the customer, receive the quality product that you expect from NAPOLEON®.
10.0 SERVICE HISTORY 43.1 W415-0752 / B / 06.03.
11.0 NOTES 44.1 W415-0752 / B / 06.03.
