This gas grill must be used only outdoors in a well-ventilated space and must not be used inside a building, garage, screened-in porch, gazebo or any other enclosed area. EN APPLY SERIAL NUMBER LABEL FROM CARTON Serial No. XXXXXX000000 MODEL NO. DE PG.35 DO NOT DISCARD BIPRO 500 WARNING! CABINET FRAME, CABINET AND COUNTER TOP MUST BE MADE FROM NON-COMBUSTIBLE MATERIAL. DANGER IF YOU SMELL GAS: • Shut off gas to the appliance. • Extinguish any open flame. • Open lid.
Quality System Certified To EN 9001-2008 All NAPOLEON gas grills are manufactured under the strict Standard of the world recognized ISO 9001-2008 Quality Assurance Certificate. NAPOLEON products are designed with superior components and materials, and are assembled by trained craftsmen who take great pride in their work. The burner and valve assembly are leak tested and test-fired at a quality test station.
WARNING! Failure to follow these instructions could result in property damage, personal injury or death. Read and follow all warnings and instructions in this manual prior to operating grill. Safe Operating Practices • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • This gas grill must be assembled exactly according to the instructions in the manual.
EN Correct Disposal Of This Product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.
Technical Data The following table lists input values for the appliance. Burner Main Rear Orifice Size I II #60 (Gross) Heat Input (Total) I II 1.45mm 1.25mm Gas Usage (Total) I II 16.0 kW 14.0 kW 1164 g/hr 1332 L/hr 5.7 kW 5.0 kW 415 g/hr 476 L/hr #50 Certified Gases / Pressures - Check rating plate to ensure that it corresponds with following list.
EN Gas Hook-Up Instructions WARNING! This grill is designed for non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes. WARNING! Cabinet frame, cabinet, and counter top must be made from non-combustible material. WARNING! The pressure supplied to the grill must conform to what is listed on the rating plate of the grill. If the supply pressure is greater, a regulator must be installed.
WARNING! • The cylinder valve(s) must be readily accessible for hand operation. A door on the enclosure to gain access to the cylinder valves is acceptable, provided it is non-locking and can be opened without the use of tools. • The enclosure for the LP-gas cylinder must isolate the cylinder from the burner compartment to provide shielding from radiation, a flame barrier, and protection from foreign material, such as hot drippings. The enclosure cannot be located directly below the grill.
Lighting Instructions EN Lights Igniter Left Burner Left Centre Burner Right Centre Burner Rear Burner Right Burner Off Position WARNING! Open lid WARNING! Ensure all burner controls are in the off position. Slowly turn on the gas supply valve. Main Burner Lighting Rear Burner Lighting (if equipped) Side Burner Lighting (optional) 1. Open grill lid 1. Open grill lid 1. Open burner cover. 2. Push and turn any main burner knob slowly to the high position.
Cooking Instructions Initial Lighting: When lit for the first time, the gas grill emits a slight odor. This is a normal temporary condition caused by the “burn-in” of internal paints and lubricants used in the manufacturing process and does not occur again. Simply run the main burners on high for approximately one-half hour. Do not locate this gas grill in windy settings. High winds adversely affect the cooking performance of the gas grill.
EN Main Burner Use: When searing foods, we recommend preheating the grill by operating all main burners in the high position with the lid closed for approximately 10 minutes. Food cooked for short periods of time (fish, vegetables) can be grilled with the lid open. Cooking with the lid closed will ensure higher, more even temperatures that can reduce cooking time and cook meat more evenly.
Cleaning Instructions Warning! Always wear protective gloves and safety glasses when servicing your grill. Warning! To avoid the possibility of burns, maintenance should be done only when the grill is cool. Avoid unprotected contact with hot surfaces. Ensure all burners are turned off. Clean grill in an area where cleaning solutions will not harm decks, lawns, or patios. Do not use oven cleaner to clean any part of this gas grill.
EN Maintenance Instructions We recommend this gas grill be thoroughly inspected and serviced annually by a qualified service person. At all times keep the gas grill area free from combustible materials, gasoline and other flammable vapors and liquids. Do not obstruct the flow of ventilation and combustion air. Keep the cylinder enclosure ventilation openings (located on the cart sides and at the front and back of the bottom shelf) free and clear from debris.
WARNING! Always wear protective gloves when changing the halogen bulb in the internal lights of your grill. Lights: To replace the halogen bulb in your grill you must first remove the lens from the light housing. To remove the lens from the housing, remove the Philips screw securing the housing in place. Snap the lens out of the housing (including the metal bracket). Do not touch the halogen bulb with your bare hands. The oil from your fingertips will reduce the life of the bulb.
EN Troubleshooting Problem Possible Causes Solution Low heat / Low flame when valve turned to high. For propane - improper lighting procedure. Ensure lighting procedure is followed carefully. All gas grill valves must be in the off position when the tank valve is turned on. Turn tank on slowly to allow pressure to equalize. See lighting instructions. For natural gas - undersized supply line. Pipe must be sized according to installation code. For both gases - improper preheating.
Problem Possible Causes Solution Burner output on “high” setting is too low. (Rumbling noise and fluttering blue flame at burner surface.) Lack of gas. Check gas level in propane cylinder. Supply hose is pinched. Reposition supply hose as necessary. Dirty or clogged orifice. Clean burner orifice. Spider webs or other matter in venturi tube. Clean out venturi tube. Ceramic tiles overloaded with grease drippings and build-up. Ports are clogged.
KEEP YOUR RECEIPT AS PROOF OF PURCHASE TO VALIDATE YOUR WARRANTY. EN Ordering Replacement Parts Warranty Information MODEL: DATE OF PURCHASE: SERIAL NUMBER: (Record information here for easy reference) Before contacting the Customer Solutions Department, check the Napoleon Website for more extensive cleaning, maintenance, troubleshooting and parts replacement instructions at www.napoleongrills.com.
Caution! During unpacking and assembly we recommended you wear work gloves and safety glasses for your protection. Although we make every effort to make the assembly process as problem free and safe as possible, it is characteristic of fabricated steel parts that the edges and corners might be sharp and could cause cuts if handled incorrectly. WARNING! Construction materials and masonry dust may cause surface damage to units and accessories.
EN BUILT-IN UNIT OPENING DIMENSIONS MODEL OPENING DIMENSIONS NOTES W D H BIPRO500 781mm 524mm 225mm SIDE BURNER 324mm 419mm 114mm OPENING OF AT LEAST 32cm2 MUST BE PROVIDED FOR COMBUSTION AIR FOR SIDE BURNER. Warning! This grill is designed for Non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes. WARNING! Enclosures must be built from non combustible materials (certified class A to EN 13501-1 standard).
BUILT-IN ACCESSORY OPENING DIMENSIONS EN OPENING DIMENSIONS PART # DESCRIPTION W H N370-0361 PF STYLE STAINLESS STEEL DOOR PICTURE 432 mm 591 mm D N370-0359 PF STYLE STAINLESS STEEL SINGLE DRAWER 438 mm 171 mm 584 mm N370-0360 PF STYLE STAINLESS STEEL TRIPLE DRAWER 438mm 578mm 584mm N370-0502-1 N370-0503-1 DOUBLE DOOR SMALL DOUBLE DOOR LARGE * FRAMES PROTRUDE FROM FACE OF CABINET BY 19 mm 718mm 959mm 514mm 514mm N370-0504 N370-0505 SIDE BURNER PROPANE SIDE BURNER NATURAL 324mm
EN BI ACCESSORY DRAWER INSTRUCTIONS 1. Unpack the drawer frame assembly. 2. Remove the drawers from the enclosure by fully extending them and then lifting up to remove them from the slides. 3. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located at the same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to ensure that the front of the enclosure is plumb. 4.
BIPRO500 BUILT-IN INSTRUCTIONS EN 102mm minimum GFI Outlet 244mm 203mm maximum 178mm LOCATED INSIDE CABINET WARNING! Failure to follow these instructions could result in property damage, personal injury or death. The grills electrical systems are pre assembled in an electrical box which must be mounted a minimum of 4” (102 mm) below the bottom of the grill as illustrated. Fasten the electrical box to the inside of the enclosure, making sure the ventilation holes are not obstructed.
EN IM-UGC500 x2 x2 N570-0038 (1/4”-20 X 1/2”) N450-0008 (1/4”-20) 1 2 3 www.napoleongrills.
EN x4 (Pre-installed at factory.) N570-0087 (1/4 -20 X 7/8”) This grill is designed for masonry, NON-COMBUSTIBLE enclosures only, and must be installed and serviced by a qualified installer to local codes. 1. Attach the side mounting brackets to each side of the grill using (4) 1/4 - 20 x 7/8” screws (N570-0087). Pre-installed at factory. 2. Lay the rear trim piece across the back of the opening. To keep it in place, a dab of silicone may be applied to each wing of the rear trim. 3.
EN Heat shield Drip pan www.napoleongrills.
EN 1 2 3 www.napoleongrills.
EN www.napoleongrills.
Leak Testing Instructions WARNING! A leak test must be performed annually and each time a cylinder is hooked up or if a part of the gas system is replaced. Warning! Never use an open flame to check for gas leaks. Be certain no sparks or open flames are in the area while you check for leaks. Sparks or open flames will result in a fire or explosion, damage to property, serious bodily injury, or death.
EN Rotisserie Kit Assembly Instruction (optional) Assemble rotisserie kit components as shown. X Ensure stop bushing is tightened on the inside of hood casting. www.napoleongrills.
Parts List Item Part # Description 500 1 N135-0049-GY1HT base casting x 2 N080-0282-GY1HT unit mounting bracket x 3 N570-0068 #14 x 1/2" screw stn stl x 4 N570-0087 1/4-20 x 7/8" screw x 5 N100-0044 main burner x 6 N080-0283 cross light bracket x 7 N010-0712 manifold assembly P N010-0713 manifold assembly n 8 N555-0025 lighting match rod x 9 N475-0402 control panel x 10 N010-0882 large LED light x 11 N010-0883 small LED light x 12 N750-0044 power wire
EN Item Parts List Part # Description 500 42 N685-0004C temperature gauge x 43 N510-0013 black silicone lid bumper x 44 N010-0813 lid handle x 45 N080-0253G lid handle cover x 46 N570-0013 #8 x 5/8" screw x 47 N735-0002 1/4" lock washer x 48 N135-0015G left side hood casting x 49 N135-0016G right side hood casting x 50 N335-0076-BK2GL hood insert x 51 N570-0012 1/4"-20 X 5/8 carriage bolt x 52 W735-0011 3/4" washer / rondelle 3/4" x 53 N080-0291 left lid
Parts List Item Part # Description 500 84 N450-0008 1/4"-20 nut x 85 N530-0023-SER regulator step down p N530-0026-SER regulator step down n N570-0032 #8 x 3/8" screw x N215-0016 wind deflector x 65213 rotisserie kit -UK ac 65212 rotisserie kit - CE ac 65233 rotisserie kit commercial -UK ac 65232 rotisserie kit commercial - CE ac 68646 vinyl cover ac 56018 stainless steel griddle ac 56040 cast iron griddle ac 67731 charcoal tray ac 62007 grease trays foil (5
www.napoleongrills.
TRANSFORMER 120V AC EXTENSION CORD GFI Outlet 12V AC FUSE HOLDER FUSE 4A SLOW BLOW C15 12V AC RECTIFIER C1 C16 1.5V DC C2 C3 LEFT HALOGEN LID LIGHT C11 JUMP WIRE IGNITER MODUAL C12 C4 IGNITER SWITCH C10 C13 C14 REAR BURNER ELECTRODE GROUND WIRE (attached to the unit) C9 LED CONTROL PANEL LIGHTS ELECTRICAL CIRCUIT DIAGRAM (BIPRO500RB MODEL) C7 C6 C8 LIGHT SWITCH RIGHT HALOGEN LID LIGHT 33 EN www.napoleongrills.
Notes EN www.napoleongrills.
Dieser Gasgrill darf nur an einem gut belüfteten Ort im Freien benutzt werden, nicht jedoch in einem Gebäude, einer Garage oder einem anderen geschlossenen Bereich. SERIENNUMMER-AUFKLEBER VOM KARTON HIER ANBRINGEN Seriennr. XXXXXX000000 Model-Nr. DE BITTE SORGFÄLTIG AUFBEWAHREN BIPRO 500 WARNUNG! FÜR DIE SCHRANKRAHMEN, SCHRÄNKE UND ARBEITSFLÄCHEN AUSSCHLIESSLICH NICHT BRENNBARE MATERIALIEN VERWENDEN. GEFAHR WENN ES NACH GAS RIECHT: • Gaszufuhr zum Gerät absperren. • Flammen löschen. • Haube öffnen.
Quality System Certified To 9001-2008 DE NAPOLEON-Gasgrills werden gemäß Qualitätssicherungsnorm ISO 9001-2008 hergestellt. NAPOLEON-Produkte bestehen aus hervorragenden Bauteilen und Materialien und werden von Fachkräften montiert, die Stolz auf ihre Arbeit sind. Vor dem Verpacken für den Versand sind Ventile und Brenner auf einem Qualitätsprüfstand leckagegeprüft bzw.
ACHTUNG! Ein Nichtbefolgen dieser Anleitung kann durch Brände oder Explosionen zu Sachschäden und Körperverletzungen, auch zu tödlichen, führen. Vorsichtsmassnahmen • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Bei der Montage dieses Gasgrills müssen die Anweisungen im Handbuch genau befolgt werden.
DE Entsorgung von Altgeräten aus privaten Haushalten in der EU Dieses Symbol auf dem Produkt oder dessen Verpackung gibt an, dass das Produkt innerhalb der EU nicht zusammen mit dem Restmüll entsorgt werden darf. Die separate Sammlung und das Recyceln Ihrer alten Elektrogeräte zum Zeitpunkt ihrer Entsorgung trägt zum Schutz der Umwelt bei und gewährleistet, dass sie auf eine Art und Weise recycelt werden, die keine Gefährdung für die Gesundheit des Menschen und der Umwelt darstellt.
Regler In der folgenden Tabelle sind die Anschlusswerte des Geräts aufgeführt. Brenner Düsengrösse I II Haupt #60 Hinten 1.25mm (Grob)Leistung(Insgesamt) I II Gasverbrauch (Insgesamt) I II 1.45mm 16.0 kW 14.0 kW 1164 g/hr 1332 L/hr #50 5.7 kW 5.0 kW 415 g/hr 476 L/hr Zugelassene Gase / Druck - Die Werte Ihres Geräts stehen auf dem Typenschild.
DE Anweisungen für den Gasanschluss WARNUNG! Dieses Grillgerät ist ausschließlich mit nicht brennbaren Schrankkonstruktionen zu verwenden und die Installation und Wartung darf nur von einem zugelassenen Installateur unter Einhaltung der geltenden lokalen Vorschriften durchgeführt werden. WARNUNG! Für die Schrankrahmen, Schränke und Arbeitsflächen ausschließlich nicht brennbare Materialien verwenden. WARNUNG! Der Gasdruck am Grillgerät muss dem am Gerät befindlichen Leistungsschild entsprechen.
WARNUNG! • • • • Das Gasflaschenventil muss für Handbedienung problemlos zugänglich sein. Eine Schranktür kann installiert werden, um problemlosen Zugang zum Gasflaschenventil zu ermöglichen, es muss jedoch sichergestellt sein, dass die Tür nicht verriegelbar und ohne Werkzeuge zu öffnen ist. Der Gasflaschenschrank muss die Gasflasche effektive vom Brennerabteil trennen und Schutz bieten vor Strahlung, Flammen und Fremdstoffen, beispielsweise heißen Bratensäften.
Zündanleitung DE Lampen Zünder Linker Brenner Linker Mittlerer Brenner Rechter Mittlerer Brenner Hinterer Brenner Rechter Brenner ACHTUNG! Haube öffnen. Ausschaltstellung ACHTUNG! Stellen Sie sicher, dass alle Brenner-Bedienelemente auf „OFF” (Aus) gestellt sind, und öffnen Sie das Gasventil an der Gasquelle. Anzünden des Hauptbrenners Anzünden des rückseitigen Brenners (Rotisseriebrenner) Anzünden der Seitenbrenner (Falls vorhanden) 1.Haube öffnen. 1. Haube öffnen. 1.
Grillanleitung Beim allerersten Erhitzen gibt der Gasgrill einen leichten Geruch ab. Der Geruch wird durch das „Einbrennen” der Innenlacke und Verdunsten der Schmiermittel aus der Fertigung verursacht, ist ganz normal und tritt später nicht mehr auf. Vor der ersten Benutzung sollten Sie darum die Hauptbrenner etwa eine halbe Stunde mit größter Hitze brennen lassen.
DE Grillen Mit Den Hauptbrennern: Vor dem Anbraten von Grillgut wird 10 Minuten Vorwärmen empfohlen. Dafür werden alle Hauptbrenner auf die höchste Stufe gestellt und die Haube geschlossen. Kurz zu grillende Nahrungsmittel wie Fisch und Gemüse können bei offener Haube gegrillt werden. Beim Grillen bei geschlossener Haube ist die Temperatur gleichmäßiger und höher, sodass die Grillzeit kürzer ist und das Fleisch gleichmäßiger gegrillt wird. Benötigt ein Grillgut länger als 30 Minuten, wie z. B.
Reinigungsanleitung 45 Vorsicht! Beim reinigungsanleitung sollten Arbeitshandschuhe und eine Schutzbrille getragen werden. Vorsicht! Zum Reinigen müssen die Brenner ausgeschaltet sein. Heiße Flächen nicht ungeschützt berühren. Grill an einen Ort stellen, wo das Reinigungsmittel keinen Schaden anrichten kann (nicht auf die Terrasse oder den Rasen). Kein Teil dieses Gasgrills darf mit Ofenreiniger gesäubert werden. Grillroste oder andere Teile des Gasgrills nicht in einem selbstreinigenden Ofen säubern.
Wartungs Anleitung Der Gasgrill sollte jährlich von einem zugelassenen Wartungsdienst überprüft und gewartet werden. Brennbare Materialien, Benzin und andere brennbare Dämpfe und Flüssigkeiten müssen entfernt vom Gasgrill gelagert werden. Luftwege zur Belüftung und zum Brenner nicht blockieren. Lüftungslöcher des Gasflaschenschranks (an den Grillwagenseiten und der Vorder- und Rückseite des unteren Regalbodens) stets frei von Schmutz und Ablagerungen halten.
Vorsicht! Verwenden Sie beim Wechseln der Halogenlampe in Ihrem Grill stets Schutzhandschuhe. Lichter: Um die Halogenlampe in Ihrem Grill zu ersetzen, müssen Sie zuerst die Glasabdeckung aus der Fassung entfernen. Um das zu tun, entfernen Sie die Philips Schraube, die die Fassung fixiert. Schnipsen Sie die Glasabdeckung inklusive Metallteil aus dem Gehäuse und verhindern Sie eine Berührung der Halogenleuchte mit der bloßen Hand. Das Fett der Haut kann die Lebensdauer der Halogenleuchte verringern.
Fehlerbehebung Problem Mögliche Ursachen Lösung Geringe Hitze / kleine Flamme auf Stellung „High“. Bei Propangas – die Anweisungen für das Anzünden wurden nicht befolgt. Die Anweisungen für das Anzünden genau befolgen. Alle Gasgrillventile müssen sich in der Stellung „OFF“ (Aus) befinden, wenn das Ventil für die Gaszufuhr geöffnet wird. Die Gaszufuhr langsam öffnen, um Druckausgleich zu ermöglichen. Siehe Anweisungen für das Anzünden. Bei Erdgas – Leitung für die Gaszufuhr zu klein.
Problem Mögliche Ursachen Lösung Brennerleistung auf Stufe „High“ ist zu niedrig. (Rumpelnde Geräusche und flatternde blaue Flamme an der Brenneroberfläche.) Zu wenig Gas. Kontrollieren Sie den Gasstand in der Propangasflasche. Zufuhrschlauch ist eingeklemmt. Zufuhrschlauch falls nötig neu positionieren. Schmutzige oder verstopfte Öffnung. Brennerauslass reinigen. Spinnweben oder anderes Material in der Venturidüse. Venturidüse reinigen.
BEWAHREN SIE IHRE QUITTING ALS KAUFNACHWEIS AUF, UM IHREN GARANTIEANSPRUCH ZU VALIDIEREN. BESTELLUNG VON ERSATZTEILEN GARANTIE-INFORMATIONEN DE MODELL: KAUFDATUM: SERIENNUMMER: (Alle für einen Garantieanspruch benötigten Informationen hier aufzeichnen) Bevor Sie sich mit dem Kundenlösungen setzen, besuchen Sie bitte die Napoleon-Website unter www.napoleongrills.com, um ausführlichere Informationen zu Reinigung, Wartung und Pflege, Fehlerbehebung und Ersatzteile zu erhalten.
Achtung! Wir empfehlen beim Entpacken des Geräts und bei der Montage Arbeitshandschuhe und eine Schutzbrille zu tragen. Wir unternehmen alle Anstrengungen, den Montageprozess so problemlos und sicher wie möglich zu machen, doch bearbeitete Stahlteile haben üblicherweise scharfe Kanten und Ecken, die zu Schnittverletzungen führen können, wenn sie während der Montage unsachgemäß gehandhabt werden.
ABMESSUNGEN DER EINBAUÖFFNUNG DE MODELL ABMESSUNGEN DER ÖFFNUNG W D H BIPRO500 781mm 524mm 225mm Seitenbrenner 324mm 419mm 114mm ANMERKUNGEN ZUR KORREKTEN ENTLÜFTUNG DER SEITENBRENNER MUSS EINE ÖFFNUNG VON MINDESTENS 32cm² VORHANDEN SEIN. ACHTUNG! Dieser Grill darf nur in feuerfeste Materialien montiert werden und soll von einem qualifizierten Fachpersonal je nach regionaler Vorschrift gewartet werden.
EINBAUGERÄTZUBEHÖR – ABMESSUNGEN DER EINBAUÖFFNUNG ABMESSUNGEN DER ÖFFNUNG TEILENR.
EINBAUGERÄTZUBEHÖR – MONTAGEANWEISUNGEN FÜR SCHUBLADE 1. Schubladenrahmenbausatz der Verpackung entnehmen. 2. Schubladen vollständig aus dem Schrankgehäuse herausziehen und dann anheben, um sie aus den Gleitschienen zu entfernen. DE 3. Öffnung mit Unterlegstücken ausgleichen, bis die Schränke schlüssig in die Öffnung eingepasst sind. Sicherstellen, dass sich die Unterlegstücke seitlich auf gleicher Höhe mit den Bohrlöchern für die Schrankbefestigung befinden. Die Unterseite der Öffnung ggf.
BIPRO500 EINBAUANWEISUNG DE 102mm minimum GFI Outlet 244mm 203mm maximum 178mm INSIDE-Schrank WARNUNG! Die Nichtbeachtung dieser Anweisungen kann zu Sachschäden, Verletzungen oder zum Tod führen. Die Elektrosysteme des Grills sind in einer Box vormontiert, die mindestens 102 mm (4“) über dem Boden des Grills befestigt werden muss (wie dargestellt). Befestigen Sie die Elektro-Box an der Innenseite des Grillunterschranks und vergewissern Sie sich, dass die Belüftungsöffnungen nicht blockiert sind.
IM-UGC500 DE x2 x2 N570-0038 (1/4”-20 X 1/2”) N450-0008 (1/4”-20) 1 2 3 www.napoleongrills.
x4 (Werksseitig vorinstalliert.) N570-0087 (1/4 -20 X 7/8”) Dieses Grillgerät ist ausschließlich mit NICHT BRENNBAREN Schrankkonstruktionen in Mauerbauweise zu verwenden und die Installation und Wartung darf nur von einem zugelassenen Installateur unter Einhaltung der geltenden lokalen Vorschriften durchgeführt werden. 1. Seitliche Befestigungen und Seitenabschlussteile mit den beiliegenden (4) Nr. 1/4- 20 X 7/8” -Schrauben (N570-0087) an beiden Seiten des Grills montieren. Werksseitig vorinstalliert.
DE Hitzeschild Tropfpfanne www.napoleongrills.
1 DE 2 3 www.napoleongrills.
DE www.napoleongrills.
Anleitung Für Die Leckageprüfung ACHTUNG! Ein Leckagetest muss vor der ersten Benutzung, jährlich und nach Auswechseln oder Warten eines Gasbauteils durchgeführt werden. ACHTUNG! Während der Prüfung ist Rauchen verboten. Alle Zündquellen sind zu entfernen. STOP Leckageprüfung: Ein Leckagetest muss vor der ersten Benutzung, jährlich und nach Auswechseln oder Warten eines Gasbauteils durchgeführt werden. Während der Prüfung ist Rauchen verboten. Alle Zündquellen sind zu entfernen.
Anweisungen für die Montage des Drehspieß-Sets (optionale) Komponenten des Drehspieß-Sets wie gezeigt montieren. DE X Sicherstellen, dass die Anschlagbuchse an der Innenseite des Haubengussteils fest angezogen ist. www.napoleongrills.
Stückliste Item Part # Description 500 1 N135-0049-GY1HT base casting x 2 N080-0282-GY1HT unit mounting bracket x 3 N570-0068 #14 x 1/2" screw stn stl x 4 N570-0087 1/4-20 x 7/8" screw x 5 N100-0044 main burner x 6 N080-0283 cross light bracket x 7 N010-0712 manifold assembly P N010-0713 manifold assembly n 8 N555-0025 lighting match rod x 9 N475-0402 control panel x 10 N010-0882 large LED light x 11 N010-0883 small LED light x 12 N750-0044 power wire
DE Stückliste Item Part # Description 500 42 N685-0004C temperature gauge x 43 N510-0013 black silicone lid bumper x 44 N010-0813 lid handle x 45 N080-0253G lid handle cover x 46 N570-0013 #8 x 5/8" screw x 47 N735-0002 1/4" lock washer x 48 N135-0015G left side hood casting x 49 N135-0016G right side hood casting x 50 N335-0076-BK2GL hood insert x 51 N570-0012 1/4"-20 X 5/8 carriage bolt x 52 W735-0011 3/4" washer / rondelle 3/4" x 53 N080-0291 left li
Stückliste Item Part # Description 500 84 N450-0008 1/4"-20 nut x 85 N530-0023-SER regulator step down p N530-0026-SER regulator step down n N570-0032 #8 x 3/8" screw x N215-0016 wind deflector x 65213 rotisserie kit -UK ac 65212 rotisserie kit - CE ac 65233 rotisserie kit commercial -UK ac 65232 rotisserie kit commercial - CE ac 68646 vinyl cover ac 56018 stainless steel griddle ac 56040 cast iron griddle ac 67731 charcoal tray ac 62007 grease trays foil (5
www.napoleongrills.
TRANSFORMER 120V AC EXTENSION CORD GFI Outlet 12V AC FUSE HOLDER FUSE 4A SLOW BLOW C15 12V AC RECTIFIER C1 C16 1.5V DC C2 C3 LEFT HALOGEN LID LIGHT C11 JUMP WIRE IGNITER MODUAL C12 C4 IGNITER SWITCH C10 C13 C14 REAR BURNER ELECTRODE GROUND WIRE (attached to the unit) C9 LED CONTROL PANEL LIGHTS ELECTRICAL CIRCUIT DIAGRAM (BIPRO500RB MODEL) C7 C6 C8 LIGHT SWITCH RIGHT HALOGEN LID LIGHT 67 DE www.napoleongrills.
Napoleon products are protected by one or more U.S. and Canadian and/or foreign patents or patents pending.