This gas appliance must be used only outdoors in a well-ventilated space and must not be used inside a building, garage, screened-in porch, gazebo or any other enclosed area. EN APPLY SERIAL NUMBER LABEL FROM CARTON Serial No. XXXXXX000000 MODEL NO. FR PG.27 PATIOFLAME OUTDOOR GAS FIREPIT GPFR60 GPFS60 DANGER! CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide, which has no odor. Using it in an enclosed space can kill you.
EN Napoleon President’s 3 Year Limited Warranty NAPOLEON products are designed with superior components and materials, and are assembled by trained craftsmen who take great pride in their work. This product has been thoroughly inspected by a qualified technician before packaging and shipping to ensure that you, the customer, receive the quality product you expect from NAPOLEON.
! WARNING! WARNING! Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this gas appliance. ! EN Safe Operating Practices • • • • • • • • • • • • • • • • • • • • • • • • • • • • N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 3 For Outdoor Use Only. THIS APPLIANCE IS HOT WHEN OPERATING AND CAN CAUSE SEVERE BURNS IF CONTACTED.
General Information EN This gas appliance was tested and listed to Canadian and American National Standards, ANSI Z21.97-2014/ CSA 2.41-2014 “Standard for Outdoor Decorative Gas Appliance”. When an appliance is for connection to a fixed piping system, the installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, International Fuel Gas Code, Natural Gas and Propane Installation Code, CSA B149.
Specifications DIMENSIONS GPFR60 EN 7 1/4" 18cm 11 3/4" 30cm 33 1/4" 84cm 6 1/4" 16cm 5 3/4" 14cm 1/4" 1cm 28 3/4" 73cm 4" 10cm 3 1/4" 8cm 2 3/4" 7cm GPFS60 25 3/4" 66cm 25 3/4" 66cm 6 1/4" 16cm 5 3/4" 14cm 20" 50cm 2 1/2" 6cm 1/4" 1cm 4" 10cm 3 1/4" 8cm 5 1/4" 13cm N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 5 www.napoleongrills.
INPUT EN MODEL FUEL MAX. INPUT Btu/Hr GPFR60 GPFS60 Natural Gas 60, 000 GPFR60 GPFS60 Propane Gas 60, 000 GAS INLET PRESSURES Maximum Inlet Pressure NATURAL PROPANE 7.0" w.c. 11.0" w.c. MINIMUM CLEARANCE TO COMBUSTIBLES INCHES MM Side Walls 24 610 Top of unit to ceiling 72 1830 Floor 9 229 CENTRE OF PATIOFLAME 24” (610mm) MAXIMUM OVERHANG 72” (1829mm) 9” (229mm) 24” (610mm) www.napoleongrills.com N415-0310 Jan 11.19.indd 6 N415-0310 Jan 11.
Location Locating Your Outdoor Appliance ! EN It is important when selecting a location for your appliance to ensure clearances to adjacent combustibles are met. This appliance is intended for installation on an outdoor patio or in your yard. It is highly recommended that this appliance be installed in a sheltered area (following the guidelines outlined below). Direct wind will cause an erratic flame and possible pilot or main burner outage.
EN ! WARNING! Cabinet frame, cabinet and counter top must be made from non-combustible material. ! WARNING! You must have clear and easy access to the on/off valve AFTER the appliance is installed and connected to the gas supply in order to safely turn off the burner. ! WARNING! Materials placed around the burner unit will get extremely hot. They must be noncombustible and must be able to expand and contract without cracking. Tiled cement board is the preferred material.
Gas Hook-Up Instructions ! WARNING! If these instructions are not followed exactly, a fire causing death or serious injury may EN occur. Propane Cylinder Specifications ! A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a cylinder with a damaged valve. The LP-gas supply cylinder must be constructed and marked in accordance with the U.S. D.O.T.
Enclosures For LP (Propane) Gas Supply Systems If you build an enclosure for an LP gas cylinder, follow these recommended specifications. You must also follow local codes. EN • An enclosure for an LP-gas cylinder shall be ventilated by openings at both the upper and lower levels of the enclosure.
EN PARTITION TO ISOLATE CYLINDER FROM PATIO FLAME 23.5” (597mm) MINIMUM OPENING A 5” (127 mm) MAXIMUM OPENING 1” (25.4 mm) B MAXIMUM 2” (51 mm) MINIMUM NON LOCKING DOOR 5” (127 mm) MAXIMUM CYLINDER SIZE OPENING A AREA OPENING B AREA 20 lb (9.1 kg) 20 in (130 cm ) 10 in2 (65 cm2) 30 lb (13.6 kg) 30 in2 (195 cm2) 15 in2 (100 cm2) 2 2 GAS VALVE CENTERLINE 8" 20cm MIN 3 1/4" 8cm MIN. 9" 23cm MIN 15 1/2" 39cm FLOOR N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 11 www.napoleongrills.
EN Conversion to Natural Gas ! WARNING! To avoid the possibility of burns conversions should only be done when the patio flame is cool. Ensure burner is turned off. Turn gas off at source and disconnect the patio flame before beginning conversion. ! WARNING! Glass embers may have sharp edges wear safety glasses and gloves when handling. ! ! WARNING! This conversion must be performed by a licensed gas fitter, and all connections must be leak tested before operating the patio flame.
6. Reconnect the stainless steel flex connector to the orifice and tighten using (2) wrenches. 7. Place the burner back into the enclosure. 8. Fill out the conversion label included with your patio flame and apply it to the inside of the control panel access door. EN A leak test must be performed according to the leak testing instructions found in the manual. Natural Gas Hook-Up The gas appliance is designed to operate at an inlet pressure of 7 inches water column.
EN Finishing ! Glass Ember Installation WARNING! Do not use the patio flame without the glass embers in place. WARNING! Glass embers may have sharp edges, wear safety glasses and gloves when handling. Do not change or substitute the glass ember material provided with this appliance. If replacing, use only replacement glass embers available from your local authorized dealer / distributor. WARNING! Glass embers may have a fine oil residue that needs to be cleaned prior to installation.
! ! STOP 15 Leak Testing Instructions WARNING! A leak test must be performed annually, or if a part of the gas system is replaced. EN WARNING! Never use an open flame to check for gas leaks. Be certain no sparks or open flames are in the area while you check for leaks. Sparks or open flames will result in a fire or explosion, damage to property, serious bodily injury, or death. Leak testing: This must be done before initial use, annually, and whenever any gas components are replaced or serviced.
Lighting Instructions EN Igniter Contol Knob ! WARNING! Keep face and body away from burner area when lighting. WARNING! Ensure burner controls are in the off position. Slowly turn on the gas supply valve. 1. Press and hold electronic igniter button ( ). 2. Turn the burner control to the high position, press and hold in. When the burner lights, release the electronic igniter button. 3. Continue to depress the burner control knob for 30 seconds and then release.
Operating The Patio Flame ! ! ! ! ! ! N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 17 WARNING! Never use this appliance for other than the intended use. prepare food. Do not use this appliance to EN WARNING! You must have clear and easy access to the on/off valve AFTER the appliance is installed and connected to the gas supply in order to safely turn off the burner. Initial Lighting: When lit for the first time, the appliance emits a slight odor.
Maintenance / Cleaning Instructions EN WARNING! Glass embers may have sharp edges, wear safety glasses and gloves when handling. Do not change or substitute the glass ember material provided with this appliance. If replacing, use only replacement glass embers available from your local authorized dealer / distributor. ! WARNING! To avoid the possibility of burns, maintenance should be done only when the appliance is . Avoid unprotected contact with hot surfaces. Ensure burner is turned off.
Reinstallation: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when installing. Replace the glass embers. When the appliance is put back in service, check the burner flame pattern with the image below. NORMAL EN ABNORMAL Cleaning The Outer Appliance Surface: Do not use abrasive cleaners or steel wool on any painted, or stainless steel parts of your Napoleon Appliance. Doing so will scratch the finish. Exterior surfaces should be cleaned with warm soapy water.
EN Troubleshooting Problem Possible Causes Solution Low heat / Low flame when valve turned to high. For propane - improper lighting procedure. Ensure lighting procedure is followed carefully. The valve must be in the off position when the tank valve is turned on. Turn tank on slowly to allow pressure to equalize. See lighting instructions. For natural gas - undersized supply line. Pipe must be sized according to installation code. Burners burn with yellow flame, accompanied by the smell of gas.
KEEP YOUR RECEIPT AS PROOF OF PURCHASE TO VALIDATE YOUR WARRANTY. Ordering Replacement Parts EN Warranty Information MODEL: DATE OF PURCHASE: SERIAL NUMBER: (Record information here for easy reference) For replacement parts and warranty claims, contact the Napoleon dealer where the product was purchased. Before contacting the dealer, check the Napoleon Grills Website for more extensive cleaning, maintenance, troubleshooting and parts replacement instructions at www.napoleongrills.com.
EN PARTS LIST GPFR60 Item Part # Description 1 Z010-0034 burner base x 2 Z475-0016 burner surround x 3 Z585-0009 burner shield x 4 N680-0001 thermocouple x 5 Z565-0001 burner screen x 6 Z240-0001 electrode x 7 N570-0073 screw 1/4-20 x 3/8 x 8 N450-0025 nut, 1/4-20 x 9 N570-0008 screw, #8x1/2 x 10 N725-0056 valve x W455-0076 oriifce #43 p N455-0066 oriifce #25 n 11 N043-0002 battery x 12 W175-0227 flex connector x 13 N530-0003 regulator x 14 Z
PARTS DIAGRAM GPFR60 EN 5 9 3 7 9 18 2 19 1 4 8 6 12 10 14 17 15 13 16 11 N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 23 www.napoleongrills.
EN PARTS LIST GPFS60 Item Part # Description 1 Z010-0036 burner base x 2 Z475-0019 burner surround x 3 Z585-0010 burner shield x 4 Z585-0011 burner wind shield x 5 N680-0001 thermocouple x 6 Z565-0001 burner screen x 7 Z240-0001 electrode x 8 N570-0073 screw 1/4-20 x 3/8 x 9 N450-0025 nut, 1/4-20 x 10 N570-0008 screw, #8x1/2 x W455-0076 oriifce #43 p N455-0066 oriifce #25 n 11 N725-0056 valve x 12 N357-0013 ignitor x 13 N043-0002 battery x 14
PARTS DIAGRAM GPFS60 EN 8 10 4 3 9 6 2 19 1 7 5 12 17 18 13 14 11 15 N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 25 16 www.napoleongrills.
NOTES EN www.napoleongrills.com N415-0310 Jan 11.19.indd 26 N415-0310 Jan 11.
Ce l’appareil au gaz doit être utilisé uniquement à l’extérieur, dans un endroit bien aéré et ne doit jamais être utilisé à l’intérieur d’un bâtiment, d’un garage, un gazebo, une véranda avec paramoustique, ou de tout autre endroit fermé. 27 APPOSEZ LÉTIQUETTE DU NUMERO DE SERIE DU CARTON NO de série XXXXXX000000 NO DE MODÈLE FR PATIOFLAME FOYERS EXTÉRIEURS AU GAZ GPFR60 GPFS60 DANGER! RISQUE D”EMPOISONNEMENT AU MONOXYDE DE CARBONE Cet appareil peut produire du monoxyde de carbone, un gaz inodore.
Garantie limitée de 3 ans de Napoléon Les produits NAPOLÉON sont conçus avec des composants et des matériaux de qualité supérieure, assemblés par des artisans qualifiés qui sont fiers de leur travail. Ce produit a été soigneusement inspecté par un technicien qualifié avant d’être emballé et expédié pour garantir que vous, le client, recevez le produit de qualité dont vous vous attendez de la part de NAPOLÉON.
AVERTISSEMENT! Pour usage extérieur seulement. AVERTISSEMENT! Une installation non conforme, des ajustements, des altérations, un service ! ou un entretien inadéquats peuvent causer des dommages matériels. Lisez attentivement toutes les instructions d’installation, d’opération et d’entretien avant d’installer ou d’effectuer un travail d’entretien sur ce l’appareil au gaz. Pratiques Sécuritaires D’utilisation • • • • • • • • • • • • • • • • • • • • • • • • • • • • N415-0310 Jan 11.
Information Générale Cet appareil au gaz a été testé et homologué selon les normes nationales canadiennes et américaines ANSI Z21.97-2014/CSA 2.41-2014 pour les appareils au gaz décoratifs extérieurs. Lorsqu’un appareil doit être connecté à un système d’approvisionnement fixe, l’installation doit être conforme aux normes locales ou, en l’absence de normes locales, selon le National Fuel Gas Code ANSI Z223.
Spécifications DIMENSIONS GPFR60 7 1/4" 18cm FR 11 3/4" 30cm 33 1/4" 84cm 6 1/4" 16cm 5 3/4" 14cm 1/4" 1cm 28 3/4" 73cm 4" 10cm 3 1/4" 8cm 2 3/4" 7cm GPFS60 25 3/4" 66cm 25 3/4" 66cm 6 1/4" 16cm 5 3/4" 14cm 20" 50cm 2 1/2" 6cm 1/4" 1cm 4" 10cm 3 1/4" 8cm 5 1/4" 13cm N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 31 www.napoleongrills.
DÉBIT COMBUSTIBLE DÉBIT MAX. Btu/h GPFR60 GPFS60 Gaz naturel 60 000 GPFR60 GPFS60 Propane 60 000 MODÈLE FR PRESSIONS D'ALIMENTATION EN GAZ Pression d'alimentation maximale NATUREL PROPANE 7,0" c.e. 11,0" c.e. DÉGAGEMENTS MINIMAUX AUX MATÉRIAUX COMBUSTIBLES Murs latéraux Dessus de l'appareil jusqu'au plafond Plancher POUCES 24 72 MM 610 1830 9 229 CENTRE DU PATIOFLAME 24” (610mm) SAILLIE MAX 72” (1829mm) 9” (229mm) 24” (610mm) www.napoleongrills.com N415-0310 Jan 11.19.
Emplacement Emplacement de votre l’appareil extérieur Lors du choix d’un emplacement de votre l’appareil extérieur,il est important d’assurer que le dégagement près des matériaux combustibles adjacents est respecté. Cet appareil est conçu pour être installé sur votre terrasse ou dans votre cour arrière. Il est fortement recommandé que cet appareil soit installé dans un endroit couvert (selon les directives énoncées ci-dessous).
FR ! AVERTISSEMENT! La charpente du cabinet, le cabinet et le comptoir doivent être faits de matériaux incombustibles. Le cabinet doit être conçu et fabriqué pour recevoir un maximum d’un (1) cylindre au propane. ! AVERTISSEMENT! Afin de pouvoir éteindre le brûleur en toute sécurité, vous devez vous assurer d’avoir un accès facile et sans obstruction à la soupape « on/off » UNE FOIS que l’appareil est installé et branché à l’alimentation en gaz.
! 35 Branchement Au Gaz AVERTISSEMENT! Si ces instructions ne sont pas suivies à la lettre, un incendie pourrait s’ensuivre, causant des blessures graves ou la mort. Spécifications Pour La Bonbonne De Propane Un cylindre bosselé ou rouillé peut être dangereux et devrait être vérifié par votre fournisseur de propane. N’utilisez jamais un cylindre avec une soupape endommagée. Le cylindre de propane doit être fabriqué et étiqueté conformément aux spécifications américaines du D.O.T.
Enceinte pour les systèmes d’alimentation au propane Si vous désirez fabriquer une enceinte pour une bonbonne de propane, suivez les spécifications ci-dessous. Vous devez aussi vous conformer aux codes locaux. • Les enceinte pour les bonbonnes de propane doivent être ventilés par des ouvertures au niveau supérieur et inférieur de l’enceinte.
LA PARTITION DOIT ISOLER LE CYLINDRE LE APPAREIL OUVERTURE A FR 23.5” (597mm) RECOMMANDÉS 5” (127 mm) MAXIMUM OUVERTURE B 1” (25.4 mm) MAXIMUM 2” (51 mm) MINIMUM PORTE NON VERROUILLABLE 5” (127 mm) MAXIMUM TAILLE DE CYLINDRE D’OUVERTURE A ZONE D’OUVERTURE B ZONE 20 lb (9.1 kg) 20 in2 (130 cm2) 10 in2 (65 cm2) 30 lb (13.6 kg) 30 in2 (195 cm2) 15 in2 (100 cm2) VALVE CENTRALE 8" 20cm MIN 3 1/4" 8cm MIN. 9" 23cm MIN 15 1/2" 39cm PLANCHER N415-0310 Jan 11.19 N415-0310 Jan 11.19.
FR Conversion au gaz naturel ! AVERTISSEMENT! Pour éviter les risques de brûlure, la conversion doit uniquement avoir lieu lorsque le Patioflame est froid. Vérifiez que le brûleur est bien éteint. Coupez l’alimentation en gaz à la source et débranchez le Patioflame avant d’entreprendre la conversion. ! AVERTISSEMENT! Les braises de verre peuvent avoir des rebords tranchants. Portez des lunettes de sécurité et des gants lorsque vous les manipulez.
6. Rebranchez le raccord flexible en acier inoxydable à l’injecteur et serrez-le à l’aide de deux (2) clés. 7. Placer le brûleur dans l'enceinte. 8. Remplissez l'étiquette de conversion inclus avec votre flamme patio et l'appliquer à l'intérieur de la porte d'accès du panneau de commande. Faites un test de détection de fuites selon les instructions fournies dans le manuel. Branchement au gaz naturel Cet appareil au gaz est conçu pour fonctionner à une pression d’entrée de 7 po de colonne d’eau.
Finitions ! FR Installation Des Braises Vitrifiées AVERTISSEMENT! N'utilisez pas le Patioflame sans les braises vitrifiées. AVERTISSEMENT! Il est possible que les braises vitrifiées soient coupantes, portez donc des lunettes de sécurité et des gants protecteurs pour les manipuler. Ne pas changer ou substituer les braises vitrifiées fournies avec cet appareil. Si vous les remplacez, utilisez seulement des braises vitrifiées disponibles chez votre détaillant local autorisé.
! ! 41 Test De Détection De Fuites AVERTISSEMENT! Il doit être fait avant la première utilisation, annuellement et à chaque fois qu’une pièce du système de gaz est remplacée ou réparée AVERTISSEMENT! N’utilisez pas une flamme nue pour vérifier pour des fuites de gaz. Assurezvous qu’il n’y ait aucune étincelle ni flamme nue à proximité de l’endroit à vérifier. Les étincelles ou les flammes nues provoqueront un feu ou une explosion, causant des dommages matériels, des blessures graves ou des pertes de vie.
Instruction d’allumage FR Bouton d’allumeur Bouton de contrôle ! AVERTISSEMENT! Éloignez votre visage et votre corps du brûleur lors de l’allumage. AVERTISSEMENT! Assurez-vous que les commandes du brûleur sont en position éteinte. Ouvrez doucement la soupape d’alimentation en gaz. 1. Appuyez sur le bouton d’allumage électronique ( ) et maintenez-le enfoncé. 2. Tournez le bouton de contrôle du brûleur en position élevée, appuyez et maintenez enfoncé.
! ! 43 Instructions D’opération AVERTISSEMENT! N’utilisez jamais le l’appareil à des fins autres que celles prévues. Ne vous servez pas de l’appareil pour préparer de la nourriture. AVERTISSEMENT! Afin de pouvoir éteindre le brûleur en toute sécurité, vous devez vous assurer d’avoir un accès facile et sans obstruction à la soupape « on/off » UNE FOIS que l’appareil est installé et branché à l’alimentation en gaz.
Instructions d’entretien et de nettoyage AVERTISSEMENT! Il est possible que les braises vitrifiées soient coupantes, portez donc des lunettes de sécurité et des gants protecteurs pour les manipuler. Ne pas changer ou substituer les braises vitrifiées fournies avec cet appareil. Si vous les remplacez, utilisez seulement des braises vitrifiées disponibles chez votre détaillant local autorisé.
Les orifices du brûleur peuvent se boucher avec le temps à cause des débris ou de la corrosion. Utilisez un trombone déplié ou une mèche de perceuse pour les déboucher. Il est plus facile de nettoyer les orifices si le brûleur a été enlevé du le l’appareil, mais il est aussi possible de le faire quand le brûleur est en place. Réinstallation : Inversez la procédure pour réinstaller le brûleur. Vérifiez que le l’injecteur entre bien dans le brûleur lors de la réinstallation. Replacez les braises de verre.
Guide De Dépannage Problème Causes possibles Solutions Faible chaleur/petite flamme lorsque le bouton de contrôle est à “high”. Pour le propane - procédure d’allumage incorrect. Assurez-vous que la procédure d’allumage est suivie à la lettre. Tous les boutons de contrôle doivent être fermés lorsque vous ouvrez la soupape de la bonbonne. Tournez la soupape de la bonbonne lentement pour assurer l’équilibre de la pression. Voir les instructions d’allumage.
GARDEZ VOTRE REÇU COMME PREUVE D’ACHAT POUR VALIDER VOTRE Commande de pièces de rechange Information sur la garantie MODÈLE : FR DATE D’ACHAT : NUMÉRO DE SÉRIE : (Inscrivez l’information ici pour y avoir accès facilement.) Pour commander des pièces de rechange ou faire une réclamation sous garantie, communiquez avec le détaillant Napoléon où le produit a été acheté.
FR LISTE DES PIÈCES GPFR60 Article N° de pièce Description 1 Z010-0034 brûleur cuve x 2 Z475-0016 brûleur support x 3 Z585-0009 brûleur protecteur x 4 N680-0001 thermocouple x 5 Z565-0001 brûleur écran x 6 Z240-0001 électrode x 7 N570-0073 vis 1/4-20 X 3/8 x 8 N450-0025 écrou 1/4" - 20 x 9 N570-0008 vis #8 x 1/2" x 10 N725-0056 soupape brûleur x W455-0076 injecteur de brûleur propane #43 p N455-0066 injecteur de brûleur naturel #25 n 11 N043-0002 batte
DIAGRAMME DE PIÈCES GPFR60 5 9 3 7 9 FR 18 2 19 1 4 8 6 12 10 14 17 15 13 16 11 N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 49 www.napoleongrills.
LISTE DES PIÈCES GPFS60 FR Article N° de pièce Description 1 Z010-0036 brûleur cuve x 2 Z475-0019 brûleur support x 3 Z585-0010 brûleur protecteur x 4 Z585-0011 brûleur protecteur x 5 N680-0001 thermocouple x 6 Z565-0001 brûleur écran x 7 Z240-0001 électrode x 8 N570-0073 vis 1/4-20 X 3/8 x 9 N450-0025 écrou 1/4" - 20 x 10 N570-0008 vis #8 x 1/2" x W455-0076 injecteur de brûleur propane #43 p N455-0066 injecteur de brûleur naturel #25 n 11 N725-0056 s
DIAGRAMME DE PIÈCES GPFS60 8 10 FR 4 3 9 6 2 19 1 7 5 12 17 18 13 14 11 15 N415-0310 Jan 11.19 N415-0310 Jan 11.19.indd 51 16 www.napoleongrills.
N415-0310 N415-0310 Jan 11.19.