Specification

24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 • 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8
Fireplaces, Heating and Cooling: 705-721-1212 • Grills: 705 726-4278 • napoleonproducts.com
ALLURAVISION™ SERIES ELECTRIC FIREPLACE
W415-1908 / 09.21.18
Clearances
Minimum Mantel Clearances
• When using paint or lacquer to finish the mantel, the paint or lacquer must be heat
resistant to prevent discolouration.
!
WARNING
Side View (Wall Mount)
8" (203mm)
Mantel
Floor
Wall
Side View (recessed into a wall)
8" (203mm)
0"
0"
0"
Mantel
Floor
6 1/16"
152mm
4 1/2"
89mm
MIN
MAX
JUNCTION BOX
A
B
A
B
FINISHING MATERIAL
(NON-LOAD
BEARING)
Model No. A B
NEFL42CHS
16 1/8”
(41cm)
42 9/16”
(108.1cm)
NEFL50CHS
16 1/8”
(41cm)
50 13/16”
(129.1cm)
NEFL60CHS
16 1/8”
(41cm)
60 11/16”
(154.1cm)
NEFL72CHS
16 1/8”
(41cm)
74 13/16”
(190cm)
Measurements from body of appliance:
Sides, Back, Top
0”
Model No. A B
NEFL42CHD
16 1/8”
(41cm)
42 9/16”
(108.1cm)
NEFL50CHD
16 1/8”
(41cm)
50 13/16”
(129.1cm)
NEFL60CHD
16 1/8”
(41cm)
60 11/16”
(154.1cm)
NEFL72CHD
16 1/8”
(41cm)
74 13/16”
(190cm)
NEFL100CHD
16 1/8”
(41cm)
100 13/16”
(256.1cm)
4 1/2”
[89mm]
minimum for CHS
models
6 1/16”
[152mm]
minimum for CHD
models
Framing
Appliance Installation
1. Install left and right panels (FIG. 1) by securing 4 fasteners (2 per panel) to bottom of appliance
(FIG. 2).
FIG. 1
FIG. 2
Side Panel Installation (Wall Mount Installation Only)
Due to the many different materials used on different walls, it is highly recommended that you consult
your local builder before you install this appliance on the wall.
Select a location that is not prone to moisture and is located at least 36” (91.4cm) away from
combustible materials such curtain drapes, furniture, bedding, paper etc.
1. Measure the appliance and create a rough in with electrical. The electrical junction box is
located on the left side of the appliance.
2. Remove the front glass (see “front glass installation and removal” section in your manual).
3. Remove the plastic panel holders by removing the screws (FIG. 1 and 2).
5. Install trims (see “trim installation” section in your manual).
6. Hold the appliance up to ensure it will fit into the framing (see “framing - recessed
installation” section in your manual).
7. Apply shims (not supplied) between the appliance and the frame.
8. Use 4 screws to secure the appliance into the wall (FIG. 5). Do not overtighten screws.
FIG. 1
FIG. 2
FIG. 4
FIG. 3
4. If side covers are installed prior to recessed installation, remove the side covers by removing
the screws (FIG. 3 and 4).
FIG. 5
9. Re-install the plastic panel holders.
10. Place the crystals or optional topaz glass chips and drift wood logs (CHD models only)
along the media tray (see “crystal ember installation” and “optional topaz glass chips and
drift wood log installation” sections in your manual).
11. Install front glass (see “front glass installation and removal” section in your manual).
Recessing the Appliance into the Wall
2 sets of holes are provided for recessing into the wall. The wall structure may limit how far
the appliance can be recessed. Use the appropriate set of holes when recessing to the frame.
Apply shims (not supplied) between appliance and frame.
note:
It is recommended that the walls of the appliance enclosure be finishing (i.e. drywall) to avoid
exposed insulation or vapour barrier coming in contact with the appliance. This will ensure
clearance to combustibles is maintained.